Reviews
The Bolt is Steel, which is −?
When I replaced the Silencer with Other Brand Product, the Bolt of the attached Band that tightens the Exhaust pipe and Silencer was too long.
The Band is made of Stainless Steel, but the Bolt is made of Steel.
View detail
Universal Product is convenient.
Because the appearance was bad by the deterioration of Rubber of Exhaust Band, I replaced it. The design was the same and the price was cheap and it was the right answer to exchange. View detail
Up the sense of unity with the Silencer!
I am using a Trickster Silencer and bought this one to go with it.
After all, there is a sense of unity when you match them with the same brand! I think the price is just right.
View detail
That's KITACO. Cheap!
I bought a silencer band from KITACO because I changed from Earls Gear's silencerφ100 to Universal Product's silencerφ80.:It looks very beautiful and sturdy with Stainless Steel, but I had trouble fixing it because the diameter of the silencer is 1cm lower than the original one. I would be happy if there was a type that could adjust the length of the mounting part as well as the type of φ, but I guess it would be difficult considering the cost. (Especially, it is difficult to extend the length by 1 to 2 cm because you cannot put a bracket between them.) The silencer was too large, and when I put in the rubber sheet, the phi; became a little too small to reach, and I put in the 6mm spacer and installed it. By the way, Material:Although Aluminum is availableMaterial:Titanium is expensive and unprofitable, isn't it? If possible, is it possible to get a one-off price at Netetc.?
It is very helpful to have a manufacturer like KITACO who provides various universal products and parts at a good price.
Please keep up the good work. I'm rooting for you.
View detail
I used it for STREET TRIPLE!
When I installed SCORPION's Silencer to STREET TRIPLE, the Band was plastic, and when I rode a little hard, it was broken in seconds. So I bought this band and installed it. The feeling of stability was preeminent because it is made of Stainless Steel. View detail
Recommendation to Carbon silencer!
I purchased this product for Maverick's for Carbon Silencer. This product is inconspicuous Black Spec. so it blends in with Carbon Silencer, so it is Recommendation.
The carbon silencer is not conspicuous if it is silver, but this is a recommendation.
View detail
Mostly OK.
It is used for the Joint of Slip-on Silencer.
I have purchased and am using it because it is wider and can be hung more tightening torque than the OEM.
If you want to say it, I think the follow-up performance will be 100% if you don't have the R-shaped inner gold part of the Bolt tightening part.
View detail
Stable Material:Stainless Steel
I installed it on my Kawasaki ZX-11.
The exhaust band that came with the motorcycle when I bought it was ripped off during a previous touring session, so I decided to use the durable material:I chose Stainless Steel and with Brace.
Material:I heard that it often breaks by the vibration when the band is made of aluminum.
As you can see in the image, I was reinforcing it with Tie Wrap, but sadly the other side was in the same situation.
In that respect, the Stainless Steel Exhaust Band is a great big deal, and I was able to feel it again.
The supplied Rubber is a bit long, so I cut it and used it.
View detail
It's not working at all
Silencer's outer diameter is 90Φ so I bought this one
However, Size is large and Silencer could not be fixed at all
I measured the inside diameter with Caliper, 92.5 cm & hellip;
You can't use this thing
View detail
It can be used for the same as the OEM Product, etc
I purchased this for Exhaust Systemfor Replacement
It can be used in the same way as the OEM product and installed with good accuracy
The price is also less expensive than OEMs, which is enough
I was satisfied
View detail
Replace OEM is too expensive, so it excels as a Universal Product
It's just a Silencer band, but there is no problem with the texture and rubber quality
You will need to adjust the top of the head as the attachment point comes to the Center
It's a Stainless Steel plate, so you can get away with bending it back
The design is not bad and it is a very useful part for Repair
As for durability, the rubber cracks and discoloration does not occur, and the BracketBody does not crack
Necessary and sufficient
It is used for the outside 100 φ Silencer (TSUKIGI) of HORNET250
The price is so cheap and the size is so modest that it is very reliable for the poor!
View detail
A must for Silencer fixation!
GSX1300R HAYABUSA 10 year old North American Spec.
In order to attach the Titaniumium silencer of K2TEC, use the Band of exclusive use
It can be used with no problems at all in terms of build and strength
A lot of Silencer bands have come out on Universal, but the price is not different from Large It is recommended to use the special band from the Manufacturer if you want to
There seemed to be a gap in my GSX1300R HAYABUSA when I fixed it, so I had to use it It is fixed with a few washer plates
In terms of use, the Silencer holds it firmly in place without causing any vibration
If you have a 12mm wrench and a ratchet, you can replace the Silencer in just 10 seconds Work done
As for one point of concern, in my case, the fixed position of Band is the Logo of K2TEC of Silencer It is about the letter "C" in TEC Band has come and gone, so I'm going to adjust it when I remove the Tandem Footpeg in the future I think
View detail
Perfect fit
The ChamberSilencer's size is 60 pies and thin, so it wasn't easy to find it on the market But I bought it as soon as I found it, and I found a DIY bracket to fit it visually, and it fit nicely It's done It's a question of how long it can withstand vibration, but it's much better than no vibration We're going View detail
Lowest price
Buy from webike at Rakuten 。 I didn't think I could afford this price for Stevan, so I used my Rakuten Points to buy it
What about this pricing...this is a terrible thing to say just because it's exclusive
The Rubber that has been sold separately is even worse! A Rubber like that is $1,500! I bought my own Rubber and cut it off 。 I'd be willing to spend $1,500 if that Rubber would last a lifetime
Even if I sold a good Silencer of Sense, I would be disappointed if I was sold such a bad deal! ~
I bought Silencer, so I have to buy it
View detail
A well-built product
Vino (SA10J) I used it to
The exhaust system of N company is installed The exhaust system of Silencer fixed by aging
The Rivet was loose and I used the Hand Riveter to re-hit it
I'm worried about it, so I bought a Silencer band to fix it to the body of the car
The Silencer band and bracket for the body are made by the T Company
Put it between the Silencer and the attached HexagonalBolt&Nut
It's only 13mm, but Nut is 13mm, so you need to be careful about the tool you use
This is where you want them to use the 14mm Nut that is commonly used for Motorcycles
Align the Bracket with the HexagonalBolt and tighten up the HexagonalBolt to avoid wobble
Firmly fixed
The construction of the bending part is very solid, and the Material:Stainless Steel, so it will rust
It's good to have no worries
I like it because it has excellent cost performance at a reasonable price
View detail
CB1000SF Exhaust Band
The BEET OEM exhaust band ran out after 17 years, so 2.5 years ago now I bought the KIJIMA φ130mm Band and installed it and it is about 138mm A gap of about 5? It was packed with Spacer etc., but it was damaged by Tension Therefore, I used KITACO φ 140mm BandBracket with 1mm Tension Tension adjustment was carried out with one and a half rolls of Rubber and fixed in a reasonable clamping condition (Sighs) (Got it?) In the future, we will confirm this by comparing its durability with that made by KIJIMA View detail
Good Product
I Purchased this product for GPz900R. The strength of the bent portion called also is also perfectly Stainless Steel. Good Product. My Silencer band lost, but I was surprised to see it on Webike!It is a certain thing. View detail
Best Silencer Band
I will fix Kawasaki Zx14R. I purchased this product Because there is no Silencer Band. it's a special shape for BEET NASSERT Evo only. it's beautify, best material. thank you webike for best service. View detail
Agree with everyone! The price is Neck?
I think that it is impeccable construction regarding reliability.
I thought that it was OverQuality
I think there is strength.
Pierce Ranking → Bending In a series of machining processes
Is not it hard for you?
I want to know the reason why ASS'Y's product has become 2 Parts Structure.
View detail
Good Design
It was a product as I thought. There is no problem with installation and texture is perfect.
Cospa is satisfied well also in terms of price.
Image when I installed it on the car body just like I was satisfied without problems.
View detail