Reviews
Good multi bar!!
It's a really good product. Both the finish and the design are excellent. I bought the multiba twice. Thank you for your prompt delivery. I recommend this product to others, too View detail
Fits: Others
Mounted on CUB 110cc Crank bar
We replaced the Rubber part of Crank Bar's Smartphone Holder with this one.
When I run, the phone is still vibrating in Small increments due to vibration. I'm not sure how much the vibration is reduced, but I think it's good for preventing breakdowns.
View detail
It is quite good.
Although it takes 60 seconds to establish the connection due to the Radio Law, this product uses a soft power supply that shuts down 5 seconds after the ACC power is disconnected, so even if your car model shuts down the ACC power at the time of cell start, as seen in BMW etc., the power will not be turned off when the engine starts. Therefore, if you put on the Helmet and Gloves after turning on the key first, you will be connected to your smartphone by the time you step over and turn on the Cell, and you will not feel the stress of waiting for the connection.
If your vehicle is equipped with a 12~16mm GPS Mount Bracket, the Tanax AIO-5 Mounting Bracket can be used without modification.
The cost performance is great, but the screen size of 4.5-inches is a little insufficient.
View detail
Holder's clattering sound is gone.
[How is it used?
I bought this product additionally because I was told that iPhone breaks Camera by vibration.
Was the one you received as per Image?
It was larger than I expected.
How was your experience with it?
I am not sure if the vibration of the phone itself is reduced and the Camera is protected, but the Smartphone Holder itself used to make a rattling sound, but that sound has disappeared, so I think the vibration is absorbed.
[Points to note]
The mounting position needs to be adjusted as it increases the bulk considerably.
How did it compare to other products?
I wanted to use DAYTONA's Smartphone Holder, so I didn't compare it to other products.
View detail
Paint job is messy?
Matte paint nomenclature is present, but the overall texture of the paint is nowhere near as good.
The peeling paint on the Bolt is particularly disappointing.
Nevertheless, it is nice to be able to add Accent by using the Cap bolt collar, which is sold separately.
View detail
Circuit Running
I want to measure lap time in Circuit.
Purchased
I still need to know where to install the Sensor part and Wiring.
It was Large strange to pull it in.
We will verify if Time can actually be picked up properly.
View detail
Used as Bracket for Switch on Grip heater
The Bracket that was originally attached was too long and was bent at the Prank, breaking it off at the base.
This time, I don't think it will be tampered with because the base LARGE size and height of the base are just right and not uncomfortable.
View detail
Large sturdy even on Motorcycle as it is firmly fixed.
I use it on my Insta360 X3. (I'm planning to buy Ace soon, so I'll use it there as well.)
With X3, the position is so delicate that it just hits the chin of the full face, so I think other ActionCamera would have no problem at all,
The Camera is easy to put on and take off, and since it has two clasps, the Camera will not be upside down as is often the case with products that hang from the neck.
The fact that it is an official Insta360 product is also a reassuring factor.
It can be used for walking around town or in the mountains, except for motorcycle, and since the price is only 3,000 yen, one can be used for various situations and is very cost effective.
View detail
cc110 smart phone device
It is integrated with the windshield.
Good safety features as it is in an easy-to-see position.
View detail
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
It can be used with a turnstile.
I bought this to attach my old Porch and Smartphone Case to my Scooter.
As others have stated in their reviews, it rotates when installing the Porch and other parts.
I solved the problem by adding a Nut to stop the loosening.
Because of its high quality, the appearance of the product without Porch and other products is not bad.
View detail
Easy to use
[How is it used?
I chose to install a new Smartphone Holder on my TouringMotorcycle and ultimately ended up with this product.
Anything as long as it's cheap!" I am very happy to be able to do this, And not too much of Plastic's cheap stuff, either." For me, I'm a bit of an either/or kind of guy. That's it! It seemed like a good idea.
Also, my phone has many buttons on the Right side, so I could not use the type that is inserted from the side, so I chose the type that is fixed at the four corners.
Was the one you received as per Image?
I chose Black and it was just like the Image.
How was your experience with it?
First of all, the Included Parts:are substantial for the price.
There is a diameter conversion rubberretc.Pattern and it is not difficult to install.
When the middle Button is pressed, the four corners are Fit to the phone.
Release is Quantity:Pair (for Left and Right) The only thing you need to do is to press the "+" and "-" prongs, so everything can be done with one hand while doing Gloves, which is easy.
[Points to note]
Make sure it is firmly secured before starting.
How did it compare to other products?
I had been using Chinese several hundred yen ones, but I felt they were well thought out with good strength and ease of use.
【Review】
I used to think that KaEdia was cheap or bad, but when I bought it this time, I got a good impression of Included Parts:, usability, etc.
As a smartphone mount, I have no complaints.
View detail
Easy.
Large is just right.
I change equipment from time to time, and it is useful because I can exchange it easily.
View detail
Fits: SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSX-R1000, KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1400 (ZX-14)
On Stem Mount
[How is it used?
GSX-R600 (K6) I purchased this product to install DAYTONA's Multi Bar on my
The compatibility list said that the model year was 2008 or later, but I measured the diameter on the actual vehicle and confirmed that there was no problem, so I chose this model.
Was the one you received as per Image?
I had bought other Sizes before, so it was as per Image.
How was your experience with it?
I confirmed beforehand that Size was fine, so of course I could use it.
Simply put it through the Mount on the Multi Bar, put it in the Stem Nut, and then tighten the Bolt.
Multi Bar could be fixed Firmly.
[Points to note]
It is recommended to measure the diameter of your motorcycle in advance as well as the fit.
How did it compare to other products?
I chose DAYTONA because it was troublesome to check the compatibility with Multi Bar or the hole diameter, etc.
Depending on the price, a cheap No Brand product would be fine.
【Review】
You can easily fix the Multi Bar to the Stem.
It is recommended to measure the inside diameter of your car's Stem to be sure.
View detail
Touch screen is slow to respond. Instruction Manual is too easy.
The instruction manual only describes it roughly, so you have to learn how to use it by hand. Except for disassembling the bike, wiring is not difficult with color-coded connectors. However, since the connectors for the front and rear cameras are the same color, it is recommended to temporarily turn on the power in the middle of the installation (since the rear camera has a reversing function). If you are concerned about the dark current, the instructions say to connect both ACC and constant power to ACC, but I connected ACC and constant separately because I was concerned about the inability to use the parking monitoring function and the time gap. If you use your motorcycle infrequently and are concerned about battery drain, it is better to use only the ACC connection for constant and ACC. As mentioned in the title, the response of the touch screen is sluggish. It is frustrating with gloves on. There is no automatic screen illumination adjustment (I always use max except at night). The smartphone app is supposed to be able to connect to the driver's recorder, but I don't know the password, so I still can't use it. The home button on the map screen is annoying. View detail
For the use of Income.
I have been using a btx2 pro s with a SZ-RAM4 and bought it with Speaker so that I could use it with my new SHOEI Z-8. I was so attached to the SZ-RAM4 that I couldn't bear to retire it, and since I would likely want to use Jet in the hotter months, I decided to keep it too. I decided to keep it, and the question arose as to what to do with Income.
When using Income, the Microphone is available in Included Parts:for full face, and it is sufficient to use the unused one in Included Parts:for the mounting Clamp, but the Speaker and SlideMount need to be replaced or newly prepared each time they are used. However, the Speaker and SlideMount need to be replaced or newly prepared each time they are used.
I thought about changing the Speaker and SlideMount for each season, but I decided to purchase the Speaker and SlideMount because it is troublesome to take off the interior and put on and off each time, and if I just attach the Body, I can use different Helmets depending on my mood. I decided to purchase a Speaker and a SlideMount.
For installation, we decided to use double-sided tape to attach the outside of the clamp, which was not used in the Included Parts:section, to the helmet, but the SlideMount, which we purchased additionally, does not come with two screws to fasten it to the clamp, We had to think of a way to fix it to the Clamp. At first, I was thinking of using one screw for each SZ-RAM4 and Z-8, but I didn't want to damage the screws by applying excessive force, so I decided to prepare screws. However, this was not the Size sold around the corner. I had to buy a clamp to attach the screws, and it cost about 2,000 yen for two small screws. I had no choice but to use the regular screws for the Z-8, and for the SZ-RAM4, which is likely to be used less frequently, I removed the Clamp once, removed the Screw holder from the Clamp, and fixed the SlideMount to the Clamp with 2.5mm diameter Screws and Nut to make it ready to be used. The Clamp was removed and the Screw holder was removed from the Clamp.
As for the wiring, in the SZ-RAM4, the wires were placed inside the helmet, crossing the edge of the helmet, so it was necessary to protect the wiring from damage when the helmet was placed on the ground, etc. In the Z-8, the wiring could be pulled inside the helmet without passing through the point where it hits the ground, etc., so no protection was needed. However, with the Z-8, it was possible to pull the wiring inward without passing through the point where it hits the ground, so no protection was needed, and the wiring was well concealed, making it look very refreshing.
After installation, it works fine and I can now use Income on my Z-8. For this gold price, I would like to see at least a Screw included in the kit.
View detail
For the use of Income.
I am using btx2 pro s with SZ-RAM4 and bought it with Mount to be able to use it with my new SHOEI Z-8.
SZ-RAM4 has been in use for about 8 years, and it was time to retire it, but we decided to keep it because we were attached to it and could not bear to throw it away, and also because we would want to use Jet in the hot season.
In order to use the Income, the Microphone is available in the Included Parts:for full face, and it is sufficient to use the unused one in the Included Parts:for the Mount, but the Speaker and SlideMount need to be replaced each time they are used or prepared anew. Speaker is attached with Magic tape, and there is a spare tape included, so I thought about changing it every season, but later I thought it would be too much trouble and I might leave it on one side or the other.
The Z-8 has a recess for mounting the Speaker and a cutout to release the Wiring, kindly designed with Income mounting in mind.
The recess for mounting the speaker has a diameter of more than 40mm, and this C1294.10 would have fit just fine if it were a normal round type, but since the body is egg-shaped, it was a shame. By the way, it did not fit into the recess, and the One Side floated. It doesn't hit my ear and Magic tape seems not to come off easily because it is half attached, so I will use it as it is for now.
The sound level is sufficient for listening to music while riding a motorcycle. I was not dissatisfied with the sound of the SZ-RAM4 I had been using, but with the new Z-8, perhaps because the speaker is closer to my ear than with the SZ-RAM4, I feel that the volume is larger and the wind cutting sound is less and much quieter, so the sound has been improved. I felt that the sound was better.
I can't wait to go touring with my new Helmet.
View detail
Depends on the use of Main.
I purchased Mirror as Main, which is easy to see during the day.
I bought this one considering the cosmetics including Included Parts:because it was difficult to see the screen in Situation where the sun shines during the daytime with my previous driver's recorder with Monitor.
The screen visibility is not as good as the Tanax SMARTRideMonitor installed on Main's Motorcycle, but if you don't compare it to the Tanax SMARTRideMonitor, you can see the screen even in daylight at a perfectly acceptable level.
In terms of the total price including the Air Pressure Monitor, I think it is a totally reasonable price.
I use it in car play, but when I want to use it in Camera screen, it tries to switch to car play by itself, so I have to operate it each time to switch the screen back.
I would appreciate it if this is fixed in a future version up, but I have no problem using it as a SMARTMonitor.
But overall satisfaction is very good.
If you are hesitant about Tanax because of the price, I totally recommend it. Quantity with the same content:Set is almost half the price, lol.
View detail
Difficult to understand the settings
It does not include a detailed instruction manual, which is a problem when it is not connected to a smartphone.
I set it up while emailing Manufacturer.
Since the Instruction Manual is the same as the Instruction Manual that comes with the DriveRecorder, it is difficult to understand whether it is not displayed due to a defect or whether it was not displayed in the first place.
View detail
For ETCBody protection
I had it installed at the shop at the same time as the ETCSetup and Body installation prior to delivery.
I thought the OEMOption would be sufficient for the quality of the product.
I am satisfied that it fits under Seat and Beauty.
View detail