Reviews
Now you can rest assured.
The original packing ran out after the fifth oil change, so I replaced it with a spare packing.
Even if there is something wrong with the packing the next time the oil is replaced due to poor installation on my part, I can replace the oil without worrying because I have another spare.
View detail
Used for Brembo caliper
I purchased the Beta pin for Caliper's Pad pin because it had run out at some point.
It was cheap and saved me a lot of money. I will be Wiring it just in case.
View detail
Do it once a year.
[How is it used?
I use it for Wire greaseUp on my Motorcycle.
We try to Grease up at least once a year.
Was the one you received as per Image?
It was just as Image.
However, without the Instruction Manual, I might not have been able to understand how to use it at first.
How was your experience with it?
It works fine, but it is a little difficult to do short Wire, etc.
When wire grease is sprayed vigorously, it overflows through the gaps.
[Points to note]
Not particularly
How did it compare to other products?
I think KITACO was the cheapest, although other manufacturers also offer this product.
I think the usage is the same everywhere, so the rest is preference.
View detail
Great item!! Highly recommend
This item is durable and well worth it. The carpet is thick and heavy duty. Perfect to use to display the bike at shows. Really vibrant colors that pop View detail
Priced right and no damage to the adjuster.
Is a great tool to adjust the rear shock compared to using a screw driver and a hammer.It would have been extremely difficult and time consuming to preload springs without this tool.Recommend getting one to add to your collection.very handy tool, very good price.add;fits with exhaust clamps,triple tree nuts of old 50-250cc motorcycles View detail
Maintenance of Chain, which I am not good at, could be easier.
I've only done simple cleaning when I sprayed oil in the past, so I think I can do it a little better from now on. View detail
Probably shoddy
I was able to use it, but the bearing assembly of the rotating part is not right.
The rotation at the time of jack-up is terribly heavy because of it.
As delivered, the grease of the moving parts was dirty and covered with iron powder and dust,
I took it all apart and Greased it up again before using it.
View detail
Convenient
I've been working on the ground, squatting, sitting or kneeling,
My buttocks would get cold when I squatted, and it hurt when I kneeled, so I covered it up with an old Towel or something like that.
I just happened to find this Matte on our site and gave it a try,
If you fold it up, you can sit on it, if you lay it down, your knees won't hurt, and it's a friendly place to keep the tools you use,
It's a good thing, isn't it? (Laughs)
View detail
Used to remove the Clutch of LETS4Palette
When removing the clutch outer of the LETS4Palette, the nut holding the clutch outer in place was used to loosen it.
I was able to loosen a nut that did not loosen at all with the 150~180mmRatchet wrench I usually use.
Because of its long overall length, it is a convenient tool that can be used to apply large torques even by human power.
View detail
Requires some getting used to.
Too thin and spoiled in Bell Hammer's Nozzle.
Is it for a little thicker Nozzles like CRC?
Or is it compatibility with the car model? (Used on deRaster400 and GSR250)
We used it twice and returned to the old method of working with the Vinyl bag to stop and pour.
It also takes quite a while for the lubricant to travel through the Hose and come out from below.
The price is something I would be willing to keep for a trial, so I think it is a good idea to buy one to try it out.
It has been on the market for a long time, so I am sure it is useful for people who are used to it.
View detail
Nicely made and very useful
Pretty good at holding motorcycle parts or softer metal you don't wish to mar with the vice teeth. I purchased 2 different jaw pads. Plastic and metal. All were very similar. They give multiple ways to hold part secure with damage. Good quality and durable. Retention magnets are weak though, slight bump and they fall off the jaws. Holding round rods at an angle or parallel to the teeth, not so much. They will warp if given too much torque. View detail
A must have tool for any tool box.
This tool comes in handy for all my little jobs and some big ones.The depth of insertion of the socket allows the optional setting of fixed and pivoting.it can be used as an extension bar.It is pretty sturdy and well made.The Japanese quality shines through, the feel in the hand is incredible. It's quick to use the handle is large enough to get a good amount of torque on the screw or nut being tightened. so far the tool has been very durable and not let me down while being used. View detail
You look good.
[How is it used?
XR230 Used for Valve Matching
Was the one you received as per Image?
Image
How was your experience with it?
We have completed the Valve matching process without any problems.
[Points to note]
It is a small package, but there is so much in it that you can't use it all.
No problem!
View detail
Low price but sufficient Quality
The price of Motion pro was too high, so I went with this one. The price is a quarter of the price, but the quality is solid and this product should be sufficient. The box is just a bonus, and the lid closure is so roughly made that it won't close after a few uses. View detail
should have got these a long time ago,Great product
Nice tools from KTC. They are well made and effective. They wood handle is nice and the packaging serves as a storage case for them. these are amazing! These little gasket scrapers work great. I actually prefer them over most other kinds in my tool box. Ive used them on everything from bikes to jeeps to and they have always worked pretty good. you just need to be extra careful on aluminum gasket surfaces with them. Since they are steel they can gouge your aluminum gasket surface if you dont know how to use them and not careful. View detail
Light and strong Tool
Expensive, but very light for carrying on rides. Easily put into a tool pack.Easy to adjust, very sturdy. A nice tool. more uses for these tools than just motorcycle riding.It serves two purposes, amateur and professional. It should be in your tool bag.Highly recommened View detail
I've been looking for you
I was going to buy something expensive at Oak Auction because it was hard to find.
I am glad I was able to purchase it here.
View detail
I think it is very cosy. It is carefully made.
I have been using Quantity for many years now.:The socket adapter of the set finally broke. I was looking for a replacement, and this product seemed to be the cheapest and the most well-made, so I bought it. I bought it because it seemed to be the cheapest and well-made product I could find. It fits very snugly and is easy to remove, and I think it is very cost effective.
I don't know about durability, but it looks good, so I gave it 5 stars.
View detail
Great tool, highly recommend
This way is much more precise. Works like a dream. Bought this tool for removing the small KTM Bendix bushings. It worked perfectly. Great tool for the price, was able to remove all of my bearings from my transmission in my KTM plan to rebuild my KTM with it as well, didn't have an issue with any of the small sizes, you just have to be sure that you are setting it up properly. Note that you'll need up to a 26 mm wrench or a crescent wrench. Seemed a little pricey for a tool you do not use that much but it will serve generations of riders in the family. Tips: Don't forget to grease the sockets, center them exactly and tighten them. View detail
It's not what it's supposed to be used for.
I bought it to see if it could be used to prevent moisture from outdoor parking.
The actual rubber sheet is less than 1mm thick, so it sometimes picks up unevenness in the ground, resulting in puddles, but since I bought it, I will use it for a while.
View detail