Reviews
Easy to do!
You can easily connect a Short Fuse to a Normal Fuse without fiddling with the power supply, but a Bullet Terminal is required. The only caution is to check the direction of current flow with a current meter when plugging in the fuse. If you connect the fuse in the opposite direction, it may cause the fuse to break. I bought it at a shop in a hurry, but it was about 100 yen cheaper at Webig's. View detail
good qulity
This is including baral fuse .Very good qulity outer matirial.eazy to fix without any modification.amon produts are always good for DIY enthusiasts. View detail
Almost good, good product.
I was able to allocate it without any problems! So far so good.
However, the Fuse BOX will not close completely.
The lid is covered and the claws of the Main are still hooked.
View detail
For easy power pickup
Used to get power for drareco
Easy power supply from Fuse box
However, the Wiring is caught on the Cover, so a little modification is required.
View detail
Easy to remove.
Power can be easily removed by simply replacing the Fuse.
I use it to charge my phone and it works fine.
I think a little modification will be needed to get Wiring out of the junction box lid, etc.
View detail
Just replace it.
I purchased a Flat Type Fuse Power Supply to install a D-UNIT made by DAYTONA. Before purchasing, you need to open the Fuse box and check from which power source you want to secure the power supply, and buy the one that fits the FuseAmpere. Installation was very easy as I only had to replace it. View detail
It's easy!
Recommended for those who are unfamiliar with power supply extraction.
Note that you need to check the Plus side in the Fuse box. If you make a mistake, the fuse may be cut off. In GB250 CLUBMAN, it is OK to replace the fuse as shown in the photo, but the wiring from the fuse makes the fuse box tight. The wiring from the fuse will cause the fuse box to be tightened, but it should be sturdy and large enough not to worry about.
View detail
Very convenient.
This Connector is used to get power from the Mini Flat Type Fuse.
This is very useful.
I often use it as a power source for my car. Most of the common vehicles have a fuse box at the foot of the vehicle.
I need to pull power to run the DriveRecorder, Radar detector, etc., but the Cigar lighter socket makes it look rather ugly...
In the case of a motorcycle, there is no Cigar lighter socket in the first place.
The Fuse is taken out from 15AFuse, but since it is via Pipe Type Fuse 5A, it will fuse if a load of 60W or more is applied. (The Fuse that is connected to the MainFuse is 15A, so the allowable power of the MainFuse is 180W. Paradoxically, if you use more than 120W on the MainFuse side, the Main will cut off if you use more than 60W)
A fuse box with a lid requires some ingenuity in terms of how the wiring escapes.
View detail
I didn't think it would be this easy.
DAYTONA
Attachment Power Supply Unit D-UNITPlus (DeeUnitPlus)
https://www.webike.net/sd/24232600/
Used to take ACC power from the
I was worried about whether the lid of the FuseBox would close properly, but it did, to the point that it never closed completely but not problematically.
Need to check continuity and be careful about the direction of insertion.
I installed a pluggable Fuse to get power before the current flows through it.
View detail
Easiest power extraction
There are three simple ways to extract power from the Gixxer 2020 MODEL~.
Bullet terminal terminal for attachment hidden under the tankLeft Side, not accessible without removing the Side cover
Computer diagnostic coupler in the ETC storage space under the Rear Sets.
And from the Spare sub of the Fuse BOX under the Front seat.
This is the quickest way to get it from here, so this guy is always there for us.
I usually use Bullet terminal, but this time I used Terminal, which is quite easy to use.
View detail
For Woofer installation
It can be used to power a subwoofer installation.
It is long enough to roll from Battery to Power amp for peace of mind.
It is of good quality and provides a stable power supply.
View detail
easy and convenient
Easily get constant power supply from the Fuse box.
The terminals are two-way, so they can be used to install multiple electrical components at once.
It is useful because it is easy to install.
View detail
That might be a little high
I bought it to get power from a Fuse box.
I can easily get power by simply replacing the Fuse.
As a product, it is easy and good.
However, considering Product Contents, we feel the price is high.
View detail
Convenient for taking out power from a flat Fuse.
This product can be easily powered by simply replacing the fuse in the Motorcycle's fuse box. No tools are required, so it is a recommendation for those who are not good at wiring work! View detail
Very easy to secure power supply
[How is it used?
In order to add electrical components, we decided to take power from Fuse, which is energized in conjunction with Ignition key.
Was the one you received as per Image?
It was exactly as it looked in the picture; it was hard to tell what the Wiring looked like coming out of the FuseBody, so that was a bit of a concern.
Was the installation difficult?
The installation itself is easy since it is just a matter of replacing the existing Ignition20AmpereFuse, but some ingenuity is required since the wiring must be routed around the FuseBOX lid so that it can be closed. Since the wiring is coming out of the FuseBody in an upward direction, in order to make it turn 180 degrees, I had to cut off a part of the pate that was heaped up to reinforce the root of the wiring attachment part, so that the wiring could turn 180 degrees without any difficulty. The following modifications have been made to allow UTurn.
How was your experience with it?
It was energized with Ignition keyOn without any problems.
[Included Parts:were they on?
There is a 10Ampere Fuse tube in the middle of the wiring. This time, it was used as it is.
[Was there anything that disappointed you?
Not particularly
View detail
Power extraction without damaging the vehicle body Harness
It is an item that can get a branch power supply by replacing it with Fuse.
When it comes to taking power out of your car or motorcycle, you may be more likely to Image an Electra tap.
It's certainly useful and widespread, and if you ask a motorcycle shop to install electrical equipment, they will often use an Electra tap.
However, as you can see from the structure, they are not only damaging to the harness on the car body, but they are also unreliable and often become a source of trouble over time.
In this case, this product can be used by replacing the Fuse, so it will not damage the harness on the car body.
By the way, personally, it is iron board to replace this with HeadlightFuse and use it as a power supply for Bach direct Relay.
I've been running it this way for years on multiple Motorcycles and have never had a Trouble.
It's one of the most reliable power extraction methods.
View detail
I needed it to install the D-UNIT.
[How is it used?
DAYTONA's Power Supply Extraction Parts "D-UNIT. I bought this product because I need to use it with D-UNIT and Fuse box. I checked it by myself, but it was not written in the Site of D-UNIT.
(I'm a beginner, so I'm honestly not sure if it was really necessary...)
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
I was able to install it without any modification.
How was your experience with it?
It's nice to know that no processing is required.
[Included Parts:were they on?
This product only.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Please check the number of voltage you need before you buy. ←People who bought various products without checking well
View detail
Note the shape of the Fuse BOX
The USB power supply was prepared to be installed under the Rear Sets. Installation was easy and only needed to replace the Fuse, but the wiring from the Fuse did not tighten against the lid of the Fuse box, an elementary mistake due to lack of confirmation.
I stopped taking it out because I was worried about it. It's a good product that's easy to use, so I'll think about converting it to something else.
View detail
Convenient to remove the power supply
The power supply and the attachment power supply can be easily taken out from the Fuse box. Because the terminal is two-way, it is convenient to install the electric parts such as DriveRecorder and ETC at a time, and a stable power supply can be done. View detail
Quick and easy power removalParts
To take out the power supply of DriveRecorder
When you don't need it anymore, you can just pull it out and put it back in.
It's equipped with Fuse, so you don't have to worry if it goes wrong.
View detail