Reviews
It cannot be pontooned. But Rim width is Quantity:Pair (for Left and Right) I like the fact that it's all even, etc.
I purchased Front 3.5J and Rear 4J. Please be careful. Personally, I think that the depth of the rim is more than enough.:Pair (for Left and Right) I bought it knowingly because I didn't want it to be a "one-size-fits-all" type of arm. If you want to mount it on your car, you should use KITACO or GKURA's Quantity.:It is better to buy a Set product. View detail
There are many kinds.
I purchased GM-MOTO's Swing Arm to attach to my CUB90.
Since this is my first time with a Manufacturer, I thought it would be better to use the same Manufacturer for the parts I use.
When I inspected the received items, there were no problems with the overall length and inside diameter.
The 25mm O.D. of the material is very similar in appearance and does not look unnatural. The installation was done beautifully.
The CUB90 is stored mainly in Garage, ridden two days a week for 15 minutes?2, and not ridden on rainy days. In the 16 months since installation, the collars have been removed from the swing arms more than 20 times for chain and sprocket changes, adjustments, etc.
Compared to the OEM steel color, the material is aluminum, so there is more wear and tear than the OEM. The surface treatment has become duller than when new.
The Wheel Collar is difficult to polish due to its location. It is better to use a protective rust remover frequently to prevent rust from occurring.
This was my first time working with a Manufacturer, and I was a bit apprehensive. However, it is very helpful that they provide parts that are specially designed for each customer's installation. I think the uniformity of the parts material is also good.
View detail
Fits: HONDA MONKEY
DAYTONA's Copy product?
DAYTONA's Copy product?
The quick quality is not bad, but it is Solidly and hardly Stroke due to Lowdown.
The screw thread on the spring that holds the spring to the top bridge has been licked, but DAYTONA's hydraulic inner fork repair item can be used. (The size of the spring winding is a little different, so some modification or hard work is required.)
Brembo caliper support for DAYTONA Inner Fork can be used without modification.
View detail
Not worth talking about. It's too thin.
For OEMShaft O.D. 11.93~.
Kochira is 11.85mm to 11.87mm in diameter.
It rattles. Somehow, it has turned into a TaperShaft!
Left11.85 Middle11.87Right11.90mm What is this?
Also, Mt. Screw's effective length is too long.
Some Swing Arm you are using has a thin shaft.
It goes wild and leaves a Screw Mountain scar.
Why did I buy this one, lol?
View detail
Think carefully before buying.
First, this Wheel has Offset 0.
Therefore, it cannot be pontooned.
I have installed it on OEMFront fork + OEM hub,
If the gear is left as it is, it will be close to the meter gear side and will hit the boots of the fork.
I opened the package and looked at it, and then I did it...…no offset...…….
What's wrong with Offset 0?
I can't help it when I want to DISC.
If I buy a Disk hub kit from the same manufacturer, will it be attached as is?
I don't think it will be easy to pop it in, since it is only a Chinese component.
I would like to see a statement such as, "Processing is required due to no offset.
Manufacturer is also a Manufacturer.
(Added:We were stumped when we inquired about it.)
Rear will change as well.
Recommendation to attach SprocketOff-set Spacer2mm in color and Rear.
Since no offset
If you don't put it in, the Chain line will not be aligned.
3.OEM hub and Tire despite 5J (110/80-8)
So Spacer is a must.
Since GCraft's Wheel is Offset.
You can pimp it
As a result, it can be installed by processing. However, it is not possible to
When you want to make a different Wheel/disc, you will have to buy a hub or put in a color. Why?
This is because the hubs need to be packed and cannot be put back together.
I'm sure a hub from the same manufacturer would fit.
No matter how far you go, Chinese is still Chinese parts.
Are you aware of the processing before you buy?
If you want to use a pontoon, use GCraft's or KITACO's Wheel.
View detail
No Recommendation on buying if you want to pimp
I bought it for MONKEY because I had used it for APE and didn't have such a bad impression of it.
It doesn't look bad,
When it comes time to install it, it is a rickety gubba-gubba.
First, the Pivot part. This is the most important part.
It comes with four Pivot Collars.
All four are RoseRose in length.
And the Pivot Collar is not long enough.
Shim adjustment is made to the width, though,
Even if you don't want the width to rattle.
The Pivot Collar is not long enough and the Swing Arm does not move when tightened.
This can only be solved by rebuilding the Pivot Collar itself.
Then, the Shaft is passed through the Pivot Collar,
It is rattling.
Since the shaft is OEM, the inner diameter of the Pivot Collar seems to be Large.
So even if you could adjust and tighten it well at this point
Even with the Shaft in, the Swing Arm is still Oversized, so the Swing Arm will be out of control.
(One-off color is the solution for us)
Next, WheelAxle Shaft.
While the outer diameter of M12Shaft is approximately 11.92~mm
Rear axle bore diameter is 12mm or more.
This one is also rattling… This one is… already!
I thought Chain Adjuster would be nice too,
There is no reference line on the Shaft side, so you have to mark it to know….
These two points. [Color] I need to Clear.
Dangerous while driving.
I really wanted to return it, but I opened the package ….
I mean, it's not like this is a non-returnable issue if you don't know how to put it on.
I understand a certain amount of QUALITY.
This one was kind of the worst….
Oh, and for the Drum.
The Brake Rod also requires modification.
It has to be angled a little to hit the suspension bracket.
It's something for people/experts who already have … lathes and such.
WeBig sometimes has a Sale.
I regret that I should have worked a little harder and bought GCraft's Swing Arm.
If anything, Tanaka Shokai's Swing Arm is better.
Is anyone using this as is 、、、、?
View detail
Recommended
I recommend it!
It was done cheaply and Wide!
View detail
Not bad!
The performance will be reduced, but … I recommend it so much for the look! View detail
Fits: HONDA MONKEY
It looks better now
Brake needed a little work.
The rest came on with no problem.
Looks much better from Rear.
The wheel is as beautiful as if it had been plated.
View detail
Quality welds
This swingarm looks great on my monkey. Has roller pivot bearings unlike the oem swingarm are bushings. It also compliments the rear suspension for a smoother ride. Although this is designed for the 5.5j wheel you can also go down to a 3.5j wheel with the correct axle shaft spacers. View detail
Perfect
For the price these are good light weight axle spacers.worked great for my 5.5j kepspeed swingarm.highly recommend these. View detail
Not bad!
Not bad construction!
Does it look good?
I'm worried about it cracking.
View detail
Cool!
I installed it to be a down fender, but the Cornering is better too!
Highly recommended!
Great design, goes with everything!
View detail
Cheap Chinese suspension that is better than Rigid
Cheap as expected. Cheap texture.
Manufacturer's Product Description It's all in the details." is a lie.
Pre-road adjustment section is distorted and cannot be adjusted properly.
The suspension is solidly rigid, and it feels as if it is moving only with Spring, which makes it bounce and almost fly over bumps in the road surface.
View detail
FrontWide
I had a 4j in my car, but I bought it to make it wider.
I think it is well made. I haven't tried it out yet, so I don't know if it's shaky or not.
View detail
ชุดสุดคุ้มจิงๆครับ..ของมาไวได้ของครบตามรูปครับ View detail
Cancellation.
I can't wait until August, so please CANCELLATE. Instead, I will buy other Swing Arm. Thank you very much for your cooperation. View detail
Buy for front and back
I bought two 4j's for front and back, but I thought the luster of the surface was uneven on the product, but I polished it well and it came out the same as the front and back. View detail
3.5j
The price is twice as much as the Chinese Wheels, but they are so beautiful that I wonder if they were Chromium Plated. View detail
Rough processing
The bolt tip is poorly processed. The last time I bought a 235mm bolt it had the normal shape, but this time the 220mm bolt has a beveled surface with no finishing work done, so I'm a little worried that it might get caught in the Lock nut. 。 It was an out-of-stock item, but I'm sorry that I didn't rush the delivery date. (It was delivered much sooner than expected, but I hope the product will be reliable even if it takes longer) View detail