Reviews
Fits: HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA NSRmini, HONDA NS-1, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS50F
Overhaul
I bought this because I wanted to build parts that would improve the performance of the engine overhaul of my NSR50. The assembly is a bit large since there is some press fitting work to be done. I don't have a hydraulic press, so I'm planning to challenge with Vise.
I don't know when I will be able to ride it, but I am looking forward to it.
View detail
Replace with new one
The new one will be replaced at the time of maintenance of the carburetor.
Quantity in 1pc. min. cheaper than HondaOEM Product:2pc. I can buy a Set, and since the performance is the same, I am replacing it with this one.
View detail
Used on NSR250. Over cool measures in winter.
It is mid-summer so I can't benefit from it yet, but I changed from Thermo-less to low temp for winter over cool measures. I wonder if I need an electric fan no matter how much I open the low temp to 50C. My cooling specifications are 140mm jungle fan. (Thousands of yen) Thermoswitch, also in the jungle, to (about 900 yen) I think I keep 71-78 degrees Celsius at the setting where the fan turns at 80 degrees Celsius when the traffic is congested at about 35 degrees Celsius in the daytime in midsummer with Thermistor sticking into Thermo Case and Radiator cap changed to 1.3, Coolant is Heat block plus.
I'm hoping to reduce the warming up time in winter.
View detail
Fits: HONDA CB400SF, HONDA CB750FC, HONDA CB900F, HONDA CBR250, HONDA CBR250, HONDA CBR250, HONDA CBX1000, HONDA MVX250, HONDA VT250F, HONDA VT250F, HONDA VT250Z, HONDA VT250Z, HONDA STEED400, HONDA VF400F, HONDA NSR250R, HONDA NSR250R, HONDA NS400R
It was saved.
Gasoline started leaking from the Fuel Cock of my GB500TT and I was thinking that I had no choice but to replace it with a new one, then I learned about this product and bought it for a trial.
The only work required was to remove the Crimp by rubbing it, cut the screws, and then reassemble the packing.
The O-Ring and Packing are the same size as the OEM, and after the replacement, the Gasoline leakage has stopped and the unit is working fine. I am very satisfied with the low cost of the repair.
View detail
Used for NSR250R, good performance
I like the fact that ChamberGasket is also included.
This Gasket is reasonably expensive for OEM, so you save money when you buy it here.
Exhaust leakage also does not occur when used with Liquid Gasket, making it a cosmetic product.
View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Extracting RCValve from NSR250R
It is safer to purchase and remove RCValve since it costs about 2000 yen. Since RCValve is no longer in production, it is important not to break it, use this items, etc., and work in a way that does not break it. View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
become brighter
The OEM Cut lens has thick and dark glass. This product has Multi-reflector and thin plastic lens, so it is much brighter than the Halogen bulb.
If you use LED or HID with Cut lens, the optical axis and high low will be Brown and bitter Brown, so it is necessary to use Multi-reflector.
The point to be concerned about in the installation to XLR80 was glad if it was attached with Seal or Rubber plug of the hole blocking at least because Position is unnecessary. it has a feeling depth than the OEMHeadlight unit, and it is difficult to organize Harness. Sponge tape is necessary to fill the gap with Cowl. The optical axis adjustment screw, spring, and screw receiver plastic need to be used with the OEM product. These are the things that I think.
Although there is a point to be concerned about, it becomes bright visibly only by exchange of the Headlight unit. There are various opinions that the making is cheap, the paint peels off, and the Position unit is loose, and I agree with that point, but when I think that it becomes bright easily, and it becomes a stepping stone to LED conversion, I thought that it was a product of high satisfaction.
View detail
Fits: HONDA NSR250R(SP), HONDA NSR250R(SP), HONDA NSR250R(SP), HONDA NSR250R(SE), HONDA NSR250R(SE), HONDA NSR250R(SE)
Clutch's connection to Smooth.
After adjusting the wire, I gripped the lever and to be honest, I don't think it got lighter. View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
Changed to LED Headlight
I bought this to use as a LED Headlight.
The position lamp can be attached, but I don't use it, so I have blinded it.
View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
Very nice
When I ordered related products for xr motard, I found that only one product can be ordered. For its appearance, the transparent part is very crystal clear, but I am also annoyed by it. I hope it will be better if there are more color choices. . View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
Definitely brighter
I used to be stunned by the darkness of the flashlight of a long time ago, but this product is definitely brighter The latest LED Headlight Standard However, the latest LED HeadlightStandard EquipmentMotorcycle is not far behind
XR100MOTARD does not have the same connector as the XR100MOTARD, so soldering and processing of the terminals are required It is
Moreover, a Position lamp is attached, but there is no use for it I blocked it with tape
I would have liked to see the Multi-reflector used as an OEM since I drive a moped at night
View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
The effect was Large
I use it with XR 100 MOTARD, but it got brighter than I imagined. You can see clearly that OEM's light distribution is not good.
Installation is easy, but I think that some ingenuity is required. Socket and Waterproof Cover should better use OEM (It is usable normally). Apart from Reflector, it was made quite reasonable.
I think that it is inexpensive against the effect. LEDs and HID will also be brighter.
View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
Mounting on Friend's Full normal KSR
* I attached it to my friend's KSR. It is a representation of my friend.
【What made you decide the purchase?】
Light was quite dark
【How was it actually used?】
It got pretty bright
Use Valve included
【Was it difficult to install? (Hard parts case)】
I scraped a little light cowl
【Please tell me the point of installation and hang (in the case of Hard parts)】
If the drip-proof Cover? Is an OEM, a gap can be formed, so remove the LightConnector,
Set the attached Cover finally
Do not be afraid to do it carefully Large durable
[Is there anything I was disappointed about?]
When Position bulb socket wears on Multi-reflector, it goes through with a throat.
【Hope for Manufacturer - Please let me know if there are any improvement points】 Required
Outside diameter of Position bulb socket? Precision of hole of Multi-reflector.
【Have you compared items?】 Required
LED Light
[Others] Any
I will add it if my friend says something.
View detail