Reviews
Is the reduction effect small!
To replace the OEM Clutch Lever, it is necessary to remove the Bar End, Grip, and Switch Box, and it is necessary to be prepared to replace the Grip depending on the situation. We tried to install and adjust it in combination with Unicorn Japan's 2-way clutch release arm, which was introduced earlier, but we could not feel the effect as much as the combination of OEM clutch lever and 2-way clutch release arm. I did not notice much effect compared to the combination of OEM Clutch Lever and 2-way clutch release arm. I think it looks a little better, but I have to evaluate that the cost performance is low. View detail
Fits: YAMAHA YZ125, YAMAHA WR250F, YAMAHA TZR250R, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA SY250F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA XT250X, YAMAHA tricker, YAMAHA SEROW250, YAMAHA SRX400, YAMAHA SRX600, YAMAHA TT250R, YAMAHA YZ125X
Installed on a WR250R
I installed it with high expectations, but not so much. (Washer 1 piece) Still, I have the feeling that the Clutch board is moving more tightly than before. View detail
![VXSeriesChain 520VX3 Steel [with Clip(FJ)Joint]](https://img.webike-cdn.net/catalogue/images/59741/520VX3_Steel_P.jpg)
Fits: KAWASAKI Z650, KAWASAKI Z250, KAWASAKI VERSYS, KAWASAKI VERSYS, KAWASAKI Ninja400, KAWASAKI Ninja250, KAWASAKI Ninja ZX-6R (ZX636), KAWASAKI Ninja 650, KAWASAKI KLX230, SUZUKI DL1000 V-STROM250, SUZUKI DL1000 V-STROM250, SUZUKI SV650X, SUZUKI SV650, SUZUKI SV650, SUZUKI GSX250R, YAMAHA YZF-R3, YAMAHA YZ250X, YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03
Those who take the highway may want to avoid...
[How is it used?
I bought this for commuting. (Replaced at 24,000 km)
Was the one you received as per Image?
Yes
Was the installation difficult?
Request with PITService
How was your experience with it?
It's from Clip, so you might want to hold off if you're going to be using it a lot for long distances or high speeds.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
Street Riding Only
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: SYM RV150, SUZUKI ADDRESSV125, SYM RV125, KYMCO GRAND DINK150, KYMCO GRAND DINK125, HONDA LEAD125, HONDA SPACY125, HONDA PCX150, HONDA PCX125
Replaced at 20,000 km
[How is it used?
Replaced after 20,000 km.
Acceleration and deceleration were normal.
How was your experience with it?
No different than OEMs
How did it compare to other products?
OEMLevel
[Points to note]
Note the direction
View detail
![[Webike Special Order] Reinforced Type Drive V Belt](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0141/23155817_1_TS.jpg)
Fits: YAMAHA SMAX, YAMAHA MAJESTYS
It was less expensive than OEMs.
I don't think it's particularly difficult if you have the tools and kills to replace the Belt, although it does feel a little stiffer than OEM. Enhancement." Could it be the Brush-bo effect of the word "Brush"?
There are no arrows for the direction of installation rotation, so be careful in installation. Perhaps the direction in which the letters can be read at the time of installation should be correct.
View detail
Shaving Radial
[How is it used?
Shaving, brembo, Radial.
Highly reliable.
Was the one you received as per Image?
Yes
Was the installation difficult?
No. If you can bleed air. If you can bleed air.
How was your experience with it?
Easy to use
[Included Parts:were they on?
No
[Was there anything that disappointed you?
None
View detail
Throttle opens less, but is heavier.
I replaced the NORMAL because it was dirty and I could buy it cheap.
Throttle becomes heavy, so it is necessary to grip the Grip firmly.
The Spring, which returns the Throttle, was incorporated by applying a Wire to the Pulley and then using a thin Picking to bring it forward and hook it.
It is frustrating to hook the spring to the stopper of the throttle body first, and then assemble it while being careful not to dislodge it.
The NORMAL opening position is better for the control at very low speeds at the start. It looks better, and the light weight of aluminum is good.
View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100
Let's change it if we're going to Bore up! (^^ゞ
KITACO's have holes in them, so they're lightweight and provide heat protection! View detail
Fits: KYMCO Vitality 50, KYMCO TOPBOY [Top Boy]., KYMCO SUPER9 50, KYMCO SUPER9 50 S, KYMCO SOONER50, KYMCO SOONER100, KYMCO Vitality 50, KYMCO TOPBOY [Top Boy]., KYMCO SUPER9 50, KYMCO SUPER9 50 S, KYMCO SOONER50, KYMCO SOONER100
MFACTORYMFR Weight Roller75g
I gave it 3 stars because I haven't used it yet so I don't know how durable it is or anything. I think the cosmetics are good. View detail
Parenthesis good but invisible.
Following the PowerKit and SPORTReinforced Clutch, the Clutch Outer was also replaced. The price is quite expensive, but the manufacturer recommends replacing the outer clutch at the same time as the clutch, so I decided to replace the outer clutch. Well, it may be a compatibility with Shoe.
The actual weight is 825g, which is only 5g lighter than the OEM. The width of the shoe contact surface is 1mm wider than OEM. I didn't feel any change in ride quality by replacing the clutch outer.
It looks good in parenthesis, and the tension is increased when working on it, but in the end it is not visible. The large wall thickness seems to have a good cooling effect. However, the Clutch is not used that often in Shiga Prefecture, so there may not be much benefit from it.
I'm going to finish the Custom for the drive system once and for all; the selection of the Weight roller may not be fully packed yet, but there's no end to it if I'm doing it.
View detail
Fits: HONDA DJ-1, HONDA DJ-1, HONDA Gyro UP, HONDA gyro X, HONDA gyro canopy, HONDA Julio., HONDA Johno., HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA baton, HONDA baton, HONDA diocesan, HONDA TODAY., HONDA TODAY., HONDA Livdio ZX, HONDA livudio, HONDA baton, HONDA baton
Functions but no hole to Wrench.
The title is true
When integrating the Clutch into the Driven, it cannot be secured because there are no holes.
If you have various tools, you can handle it, but if you don't have them, you may lack Torque tightening if you tighten it properly.
Dio that was only 35 kilos. (Mileage just under 30,000) is now close to 60, so I think its performance as Clutch is not bad.
View detail
Fits: HONDA LEAD 50, HONDA LEAD 90, HONDA ZOOMER(Ruckus), HONDA Giorno, HONDA DIO, HONDA LIVE DIO, HONDA LIVE DIOZX, HONDA SMART DIO, HONDA SMART DIO, HONDA SMART DIO, HONDA TODAY, HONDA LEAD 50, HONDA JOKER90, HONDA JOKER Helmet, HONDA GIORNO CREA, HONDA CREA SCOOPY
ALBA Weight Roller
I used it for OEMPulley.
No abnormal noise.
View detail
Fits: HONDA XR250R, HONDA XL250 DEGREE, HONDA XR250, HONDA XR250BAJA, HONDA CRF250L, HONDA CRF250L, HONDA CRF250F, HONDA CBF250, HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250M, HONDA XR250MOTARD, HONDA CL250, HONDA CRF300L, HONDA CRF300RALLY, HONDA CRF250RALLY(S), HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250L(S), HONDA CRF250M
usually
It's heavy, but looks strong! It looks durable and will not have to be replaced for the time being. View detail
Compared to OEM, the error in diameter size is Large.
Quantity:Buy 1 Set of 6pcs.2Pack
I measured the diameter.
Three approx. 6.14mm ones, the same as OEM and
There were 9 pieces of about 6.28mm.
View detail
Fits: SUZUKI street magic, SUZUKI street magic, SUZUKI street magic, SUZUKI street magic, SUZUKI street magic, SUZUKI street magic, SUZUKI street magic, SUZUKI Address 50, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz, SUZUKI zzz
The end result of the intoxication of the maximum speed increase. And the reason why it was not a compatible car model?
ADDRESS V50 '06 (CA42A) After a month of driving the car, it was discovered that the oil had been severely depleted. Later, after replacing the broken Exhaust System, I test drove the car and found that it was blowing white smoke. I had caused the oil to go up.
It is true that the upper limit of "maximum speed" is increased to Large range. However, the maximum speed on level ground is still 60 km/h, and going over 60 km/h on a downhill will put an unreasonable burden on the driver.
It is easy to install perfectly and the effect is Large. This may have been the reason why the product was not made compatible with the car model.
By the way, I was feeling a fine and small vibration at 50km/h or more. Was it because my center of gravity was shaking and the burden was being placed on that side? No way …
View detail
attachment
It is reinstalled because I can't fine tune it, maybe it was lost due to vibration. I was very happy to see that Borembo products, sold as Single Item, are available for purchase. View detail
Fits: Others , HONDA Dio, HONDA ZOOMER, HONDA TODAY
DoctorPulley Variable Weight Roller
It was a more normal Roller than I expected.
I haven't run it much yet so I don't know how durable it is.
View detail
Fits: HONDA CB50JX-1, HONDA CRF100F, HONDA CRM50, HONDA CRM80, HONDA CY50, HONDA GROM, HONDA JAZZ, HONDA MB50, HONDA MBX50, HONDA MSX125, HONDA NS-1, HONDA NSF100, HONDA NSR50, HONDA NSR80, HONDA Solo, HONDA XE50, HONDA XE75, HONDA CROSS CUB, HONDA CROSS CUB50, HONDA CHALY 50
Bolt is required separately for some car models
Since it is a Small Sprocket, a corresponding Bolt may be required depending on the car model.
If you can, you can use the Quantity:I would like you to keep it Set.
View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R
Attention!
This Quantity dedicated to 25r:The shape of the RSprocket in the Set is different from the one in the photo.
Therefore, I was disappointed that the shape was not to my liking.
Please check SUNSTAR's Homepage or other sources before purchasing.
View detail
Fits: YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh
Good product, but 2 weeks from order to arrival
The NORMAL Clutch has two pieces, but this item has three.
Be careful when you want to replace only the Clutch or Spring at a later date by reducing the ASSY.
Center spring is stronger.
So far, no problems.
However, I had to wait two weeks for delivery.
This is despite the fact that when I placed the order, the order page indicated that it would ship in 3 days.
Partner Warehouse. Into In stock." I'm just saying.
It is too late to be informed by email after the order has been accepted.
If I had been in a hurry, I would have definitely purchased elsewhere.
Even if they were waiting to be assembled, there is no way they would be so slow in communicating with FOR JAPAN MODEL.
The delay was probably due to waiting for deliveries from China, Taiwan, and other foreign countries.
View detail