Reviews
Gold parting, things are just fine.
When I installed it on the tank, the look was a combination of calmness and a sense of comfort that I had expected.
The colors are quite close to KITACO's shades.
I thought it was quite expensive and was not sure about it, but I bought it.
I was disappointed that the back side of the "Rucksack" was so smooth. I thought there was a Rucksack. So it feels heavy.
Installation is easy as all you have to do is replace it.
It is nice to know that the color does not easily fall off when the Bolt is removed as in NORMAL.
When the NORMAL collar is removed, a hole like a drain hole appears.
This color is also concealed, so I am OK with that, but I thought it was questionable whether the purpose of this hole could be continued.
The color of the Side cover is NORMAL, but I am confused about many things.
View detail
Used for installation of Rear Sets for other vehiclesOEMfootpeg diversion
Purchased as Spacer for Rear Sets installation on Z650 (Zapper) with OEM footpeg for GSX-R750.
Although it is possible to install the washer by using a stack of washers, we chose this product to improve the appearance.
No problem to install as the inner and outer diameters are the same as the Washer. The appearance has been improved to a large size, and I am satisfied.
However, if the height is WasherQuantity:The difficulty is that it is not possible to replace it completely because it was short by 1 pc.
View detail
Rear Sets installation using OEM footpeg from another car
I bought this as a spacer to install Rear Sets on my Z650 (Zapper) which is a GSX-R750 OEM footpeg. 1pc. is just a spacer and the other one was cut down on the side to fit along the plate. It was easy to process because it is made of aluminum. （I inserted a washer of the same diameter for the slightly insufficient height (as a matter of course), but it would be nice if the height could be adjusted in 2mm increments. View detail
It's like an itch (laughs).
[How is it used?
For some reason, the gap between the rear caliper and the disc rotor on my FZS600 was uneven, etc. Although there was no problem with the brake, it was bothering me, so I decided to correct it using Shim.
Was the one you received as per Image?
The thickness is 0.5mm, which is thinner than a normal washer, and the material is Stainless Steel, but it seems to bend easily if handled roughly.
Was the installation difficult?
Simply remove the rear caliper, insert the Shim between the caliper bracket and the caliper bracket, and reinstall the rear caliper. However, the brake parts must be "Important safety parts" Therefore, Torque management of the mounting bolt is important. I used a torque wrench to tighten the bolt.
How was your experience with it?
Shim1 piece is a complete Quantity:Pair (for Left and Right) I couldn't get it close to the same size, etc., and if I put two pieces on top of each other, the gap on the RotorLeft Side would be narrower.:Pair (for Left and Right) I think it could be done evenly etc., but, well, I'm not going to attack Stoic that hard (laughs).
[Included Parts:were they on?
No, there is not
[Was there anything that disappointed you?
Nothing against the product. As a result, I didn't need the 10-pack because 2 sheets were enough in the end (laughs).
Other items that would be helpful
Point of installation and hang:Brake parts are "Important safety parts" So, use a Torque wrench to tighten it.
Opinions and requests to Manufacturer:Quantities of 0.1mm, 0.3mm and 0.5mm:Set sales may be useful.
View detail
I'm glad we have this.
I needed two of them and they were just sold in two-packs, which was a big help.
Used for engine slider installation process.
The areas used are as shown in the photos.
View detail
Small but Large!
*Motivation to purchase
I could not find a spacer with the right thickness to install the ZETA ED Skid Plate.
When the clearance between the skid plate and the down tube seat is measured with a caliper and found to be 6mm. What shall we fill this Clearance with?" I was simply worried.
01mmWasher×6 sheets? ⇒Not very efficient to look and work with? ，Cut an Aluminum round bar to 6mm thickness and drill a 6.5mm hole in the Center? ⇒Since there is no ball machine or lathe, it is labor intensive and the material is expensive and not readily available?
0 Casually searching Spacer, I found that it is Aluminum, Anodized Treatment, available in a choice of colors, and even cosier!
I decided immediately to buy it.
Installation
The quantity is placed between the skid plate and the mounting surface of the down tube, together with the washer.:You just need to set it.
Insert the mounting bolt into the skid plate, insert the washer and spacer into the bolt that protrudes from the back of the bolt, and then tighten the quantitative bolt on the mounting surface of the down tube to prevent it from falling out.:Pair (for Left and Right) The tightening was divided into several times to make it even, etc.
*Appearance after installation
0It is not visible from a normal viewpoint. When you look through, the gold anodized Spacer is quite noticeable.
0Aluminum spacer was 5mm and Washer was 1mm, total 6mm spacer was just right.
0Although the spacer is not usually visible, I think it would have been better if the skid plate was shaped along the down tube side, so that the spacer would be thinner.
*What I actually felt after using it.
○ Aluminum spacer If you think about making the same kind of spec. by yourself, it will cost you a lot of time, money, strength, and energy.
0For myself. Spacer." = "Small Sana Giant Yes, sir!
View detail
![PREMIUM ZONE Cap Bolt Color [ for M 6 bolt ]](https://img.webike-cdn.net/catalogue/images/15903/91924_1_TS.jpg)
My impression changed quite a bit.
I put them around the Bolt of the Rear Mudguard. I personally thought that the color of the Bolt looked too bright before I installed it...so I bought two sets of Bolts and changed the Bolt to Black. View detail
Just as it says!
Exactly what I was expecting.
Nothing more than what is written, nothing less than what is written.
View detail
Used for PositionUp of Handlebar riser.
[How is it used?
Adjustable HandlebarRiser Mount Kit 2DGT for MT-10 Item No.:2DGT0215-BK used for PositionUp.
Was the one you received as per Image?
It was slightly different from Image.
It was not as shiny as I had imagined.
Was the installation difficult?
There is no difficulty as it simply plugs into the M10 Hexagon Bolt.
How was your experience with it?
The Handlebar's PositionUp was done so that the Position stood and it became very easy.
Adjustable HandlebarRiser Mount Kit 2DGT's Spacer does not change the OEM height and position even if all the included Spacers are used, but just using this will increase the position up by +10mm compared to OEM.
The included Spacer can be used to further raise the position, but I think this is a good compromise in terms of the length of the Cable and other components.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
[ITEMS TO BUY TOGETHER
If you are a MT-10 rider, the GILLES TOOLING Adjustable HandlebarRiser Mount Kit 2DGT Item No.:2DGT0215-BK.
[Opinions and requests to Manufacturer
Please release a glossy spec. as well.
View detail
Just a normal, usable color.
The price is very reasonable, even though other manufacturers charge twice as much for M8×20Size aluminum collars. And it comes in a pack of two.
The quality is fine.
View detail
Used with Mirror pedestals
[How is it used? Used for KIJIMA's Mirror color
Was the one you received as per Image? Yes.
Was the installation difficult? No, sir.
How was your experience with it? I'm satisfied
[Included Parts:were they on?
[Was there anything that disappointed you? None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!! The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product. If existence of W
If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product.
If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
.
.
By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
The muffler made from p's supply is treated to the address V125, and it is a chamber protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
The spacer collar made from a product chamber protector made from burial 竊?kitaco.
(#0900-093-00060, inside diameter phi8.2mm, outside-diameter phi20mm, and 30 mm in height) The engine side of the product muffler made from product muffler made from 竊?p's supply attached aluminum billet plate 竊?p's supply attached M8 aluminum-collar (outside-diameter phi20 mm and, and 14 mm in height) 竊?address V125.
A muffler mount and M8 female-screw partial we the bolt used of this customization,
- vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
It seems that its respectively different customization was given and each loves the address V125 colored with personality.
Moreover, is conversion of a muffler mentioned the common feature of customization of the address V125?
.
.
If it equips with the chamber protector made from burial, how is it as a protector to the replace muffler which you chose (the outside diameter of a white duracon resin part is phi36mm.)?
The size of the sticker of a moriwaki is about 56 mm.
Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki is a size like the semicircle.
it is just a sticker tune of a just size!! Replace muffler of the address V125 which we incidentally cannot but praise, steiner muffler made from p's supply it is -- TSU!!
View detail
It is perfect!!
It is perfect!! View detail
When carrying out custom, since an aluminum collar is fairly frequently needed, this product is dramatically helpful. Dropping during maintenance and also losing and becoming insufficient and running for buying it on the way, if you buy a mechanic you
When carrying out custom, since an aluminum collar is fairly frequently needed, this product is dramatically helpful.
Dropping during maintenance and also losing and becoming insufficient and running for buying it on the way, if you buy a mechanic youth entering ten piece since it is occasionally can also be prevented.
View detail
It used for monkey custom vehicles. it used for an engine mount portion, a caliper, and a wheel carrying out center appearance. It is found useful. It is recommended.
It used for monkey custom vehicles.
it used for an engine mount portion, a caliper, and a wheel carrying out center appearance.
It is found useful.
It is recommended.
View detail
It used for monkey custom vehicles. it used for an engine mount portion, a caliper, and a wheel carrying out center appearance. It is found useful. It is recommended.
It used for monkey custom vehicles.
it used for an engine mount portion, a caliper, and a wheel carrying out center appearance.
It is found useful.
It is recommended.
View detail
Installed on a 92 Grom.
I think it works better than I expected.
My Front fork is NORMAL, but I think a TuneUp'd Fork would be more effective.
Installation is as easy as Handlebar is heavy.
When I first put it on, I thought it was floating. I thought it was floating when I first put it on, but when I checked it carefully, it was fine.
I haven't driven the distance to work yet.
The effect I felt was that when I pushed the Motorcycle and walked around, it seemed more stable, and the feeling of handling was clearly different from when I moved it before the replacement.
I also think the Handlebar flutter before stopping and at very low speeds has been slightly suppressed.
I have not driven long distances, so I am not sure, but I was not too concerned about the effects of vibration.
Also, the transmission of road surface conditions was slightly easier than with Rubber.
This is just my personal view, so it will vary from person to person.
Unfortunately, the Instruction Manual misstates HandlebarNutTorque.
2.7N/m is a misnomer. Squeeze firmly.
I don't need my own Torque wrench, so I remember it was around 25N/m in the Instruction Manual when I got it with Visor as a rough guide.
View detail
![Premium Zone Cap Bolt Collar [for M6 Bolt]](https://global.webike-cdn.net/photo/impression/01/010963a63e961a6c10ec53139e6d5e07L.jpg)
One point
I wanted one point and I bought it. It's well made. View detail
alignment
Rear Sets position, used to avoid interference.
Quantity:1 Set of 2pcs., good product at a reasonable price.
View detail
Clutch leverWobble eliminated
Clutch lever Wobble one-shot elimination of concern
I added a bar end mirror, so if there is a Wobble, it will interfere with the Mirror Bracket, so I added this.
Smooth Clutch operation is now possible. 0
View detail