Reviews
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Fits: YAMAHA YZ125, YAMAHA WR125, YAMAHA TY250 Z SCOTISH, YAMAHA DT200 WR
Quickly to run
With the Front12T, you will be running Quickly, both on forest roads and in town.
It is affordable and I feel the effect of the replacement.
View detail
Fits: KAWASAKI ER-5, KAWASAKI GPX600R, KAWASAKI KLE500, KAWASAKI KLF220, KAWASAKI Eliminator 600, MAGNI 1000 Australia2, MOTOGUZZI 1000 Ditna RS, bimota YB-4, bimota YB-6, bimota Dietsch 1000, bimota Flannel 1000, HONDA CB1100F, HONDA CB1100R, KAWASAKI 1000GTR, KAWASAKI 250TR, KAWASAKI EN400, KAWASAKI EN500, KAWASAKI EX-4, KAWASAKI FX400R, KAWASAKI GPZ1000RX
Idling stabilized?
I changed the oil as part of maintenance, and it seems to have stabilized the idling, but I don't feel that the power is increased. I really don't know if the period to change the oil was too short and the oil was not so deteriorated, but it is an old motorcycle and I will replace the oil as soon as possible. Next time I will buy a Torque wrench and tighten it with the specified Torque. View detail
Fits: Others Wire clutchCompetition model, SUZUKI RMX450, SUZUKI RM-Z, SUZUKI RM, KAWASAKI KLX450R, KAWASAKI KX-F, KAWASAKI KX, YAMAHA WR-F, YAMAHA YZ-F, YAMAHA YZ, HONDA CRF-X, HONDA CRF, HONDA CR
Definitely lighter.
I had been using OEM Clutch for a long time, but it was too heavy and tiring, so I replaced it with this one.
To install, remove all the originally attached clutch lever and holder, leaving only the wires in place, and then install.
The dust cover is screwed on, so it must be disassembled and assembled before installation.
Also, the Clamp portion is rotated so that it is less likely to break than a regular Lever or OEM.
The Nut that adjusts the distance of the Lever is also hexagonal, a spec. that can be firmly fixed in place.
I prefer to set it quite far away, but it feels quite light when I pull the lever, I don't know if it's because of the Ratio or some other secret, but I think you can feel it the moment you hold it.
View detail
Firmly.
I could not tell how light the Clutch was, but the build quality was solid, as if it were an OEM product.
Durability, that is the most decisive factor.
View detail
520Conversion Demerit
It is cheaper than collecting OEM parts, and as you all know, there is a Merit to make the 520. However, the Noise when driving will be Large.
It sounds like the sound when the bottom of the teeth of the front sprocket (Driven Sprocket) hits the Roller of the Chain.
The OEM Sprocket has a Ring-shaped anti-vibration Rubber, which reduces Noise.
As a countermeasure, I had some DAYTONAInsulation Glass WoolSeat left over from a previous purchase at Webig, so I attached this to the inside of the Sprocket Cover.
As an effect, Noise became much smaller.
View detail
Great grip comfort
The OEM Lever for the SV650 is a good or bad bike Level, but this Lever not only looks cool, but I was surprised at the high quality when I held it for the first time after installation!
Installation is easy and takes less than 30 minutes if you have experience with grease up and lubrication of Lever!
View detail
DRCRear sprocketBolt nut
Bolt nut for the new Rear sprocket.
It is a dedicated product and fits well.
Since it is a component that can easily come off, inspection before driving is a Large cut.
View detail
No different than OEMs
Purchased due to leaking oil line. I am glad that the quality is the same as OEM and the price is lower. I will buy again when it breaks. View detail
Tightened with a slotted screwdriver.
Used to replace an oil line. It seemed to be able to close it with a hexagon, but it didn't fit slightly. I think it is a millimeter. View detail
Fits: KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400R (-2013), KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA650R, KAWASAKI VERSYS 650
For NINJA400R
Installed on NINJA400R.
Since it is an important safety part, we asked Motorcycle shop to install it.
The feel of operation, texture, etc. was perfect without any complaints.
If you are not confident about installing it yourself, ask a professional contractor to do so.
View detail
Why is the same number of Ding as OEMs so expensive….
What made you decide to buy?
I have been working on the ZX-6R for 3 years now, and the mileage is about 10,000 km. I thought it was too early to replace them, but since all the parts were available during the spring sale, I decided to replace them.
[How was the installation?
I found information that the Torque of the Engine Sprocket nut fixing the front sprocket was halfway tight, so I loosened the Engine Sprocket nut using an electric Impact wrench from Tirefor Replacement. After that, I tightened the rear brake with the torque wrench at the specified torque of 147Nm, and finally, I bent the washer over the nut using the water pump pliers to prevent it from loosening.
*We are planning to describe this replacement work in our maintenance diary. Please take a look if you like.
How was your experience with it?
At first I was not sure whether to go with 16T or not, but I liked the ride quality of the OEM, so I decided to go with 15T, the same as the OEM. So there was no change between before and after the replacement. The normal specifications list on the product page says 16T, but the 21-year ZX-6R has 15T Front, 43 Rear, 2.866 reduction ratio, and 112 Chain links.
View detail
Bolt hole in rear sprocket is Large
It is cheap and good, but the only thing that bothers me is that the Bolt hole on the Rear sprocket is Large. I'm worried that it might move during use. View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
Fits: SUZUKI JR80, BETA EVO 2T, BETA RR 2T, BETA rr 2t 300 enduro, HONDA NS-1, HONDA NSR50, HONDA NSR80, HUSQVARNA TE300, KTM 250 EXC, KTM 250 XC, KTM 250 XC-W, KTM 300 EXC, KTM 300 XC, KTM 300 XC-W, KTM 300 XC-W Six Days, KTM Freeride 250R
Required for 2nd strike.
Product Name
NGK NGK Japan Special Ceramics Standard Plug BR7ES 5122
Item Number
BR7ES
Vehicles
EXC250 (2-Stoke) 2022
Number of man-hours
10 minutes
Required Tools
Torque wrench, Hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, Plug wrench, etc.
Why did you choose this product?
I decided to purchase this one as a spare because Plug often gets covered before Race.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
It is a hassle because you have to remove the tank. It is possible without removing the tank, but it is faster.
How was your experience with it?
It is a stable and reliable NGK product. I think the price is good since it is a consumable item.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: SUZUKI GSX-R1100, SUZUKI GSX-R750, HONDA CB1000 SF, HONDA CB400SF, HONDA X4, HONDA CBR1100XX SUPERBLACKBIRD [Super Blackbird]., HONDA CBR900RR FIRE BLADE [Fireblade]., YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA XJR400, YAMAHA FJ1200, YAMAHA FJ1100, YAMAHA XS1100, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX250, SUZUKI GS1000, SUZUKI GS750, SUZUKI GSX1100, SUZUKI GSX750
Just cover it!
Funnel is bad for the engine and does not pass vehicle inspections. The RAMAIRSystem is a simple system that can be installed on the engine, and it is easier to remove than the Power Filter, so if you want to change to a funnel, you can easily remove it. View detail
Fits: HONDA XL250S L250S, HONDA NY50 All models, HONDA CROSSCUB110 JA10, HONDA All models of GIORNO CREA AF54, HONDA SUPER CUB 110 JA10, HONDA SUPER CUB 110 PRO JA10, HONDA SUPER CUB series Engine cars (50-100cc), HONDA SUPER CUB series Engine car FI, HONDA Spacy50 All models, HONDA DREAM50 AC15, HONDA Spacy80 All models, HONDA VARIE All models, HONDA MONKEY series Engine cars (50-100cc), HONDA MONKEY series Engine car FI
Very common EXGaskett
CROSSCUB110 (JA45) Used to replace the Exhaust System of
I think Gasket is the same for all Manufacturers.
No exhaust leak etc.
It was cheaper than OEM Parts.
View detail