Reviews
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Fits: YAMAHA YZ125, YAMAHA WR125, YAMAHA TY250 Z SCOTISH, YAMAHA DT200 WR
Quickly to run
With the Front12T, you will be running Quickly, both on forest roads and in town.
It is affordable and I feel the effect of the replacement.
View detail
Fits: KAWASAKI ER-5, KAWASAKI GPX600R, KAWASAKI KLE500, KAWASAKI KLF220, KAWASAKI Eliminator 600, MAGNI 1000 Australia2, MOTOGUZZI 1000 Ditna RS, bimota YB-4, bimota YB-6, bimota Dietsch 1000, bimota Flannel 1000, HONDA CB1100F, HONDA CB1100R, KAWASAKI 1000GTR, KAWASAKI 250TR, KAWASAKI EN400, KAWASAKI EN500, KAWASAKI EX-4, KAWASAKI FX400R, KAWASAKI GPZ1000RX
Idling stabilized?
I changed the oil as part of maintenance, and it seems to have stabilized the idling, but I don't feel that the power is increased. I really don't know if the period to change the oil was too short and the oil was not so deteriorated, but it is an old motorcycle and I will replace the oil as soon as possible. Next time I will buy a Torque wrench and tighten it with the specified Torque. View detail
Fits: Others Wire clutchCompetition model, SUZUKI RMX450, SUZUKI RM-Z, SUZUKI RM, KAWASAKI KLX450R, KAWASAKI KX-F, KAWASAKI KX, YAMAHA WR-F, YAMAHA YZ-F, YAMAHA YZ, HONDA CRF-X, HONDA CRF, HONDA CR
Definitely lighter.
I had been using OEM Clutch for a long time, but it was too heavy and tiring, so I replaced it with this one.
To install, remove all the originally attached clutch lever and holder, leaving only the wires in place, and then install.
The dust cover is screwed on, so it must be disassembled and assembled before installation.
Also, the Clamp portion is rotated so that it is less likely to break than a regular Lever or OEM.
The Nut that adjusts the distance of the Lever is also hexagonal, a spec. that can be firmly fixed in place.
I prefer to set it quite far away, but it feels quite light when I pull the lever, I don't know if it's because of the Ratio or some other secret, but I think you can feel it the moment you hold it.
View detail
Firmly.
I could not tell how light the Clutch was, but the build quality was solid, as if it were an OEM product.
Durability, that is the most decisive factor.
View detail
520Conversion Demerit
It is cheaper than collecting OEM parts, and as you all know, there is a Merit to make the 520. However, the Noise when driving will be Large.
It sounds like the sound when the bottom of the teeth of the front sprocket (Driven Sprocket) hits the Roller of the Chain.
The OEM Sprocket has a Ring-shaped anti-vibration Rubber, which reduces Noise.
As a countermeasure, I had some DAYTONAInsulation Glass WoolSeat left over from a previous purchase at Webig, so I attached this to the inside of the Sprocket Cover.
As an effect, Noise became much smaller.
View detail
Great grip comfort
The OEM Lever for the SV650 is a good or bad bike Level, but this Lever not only looks cool, but I was surprised at the high quality when I held it for the first time after installation!
Installation is easy and takes less than 30 minutes if you have experience with grease up and lubrication of Lever!
View detail
DRCRear sprocketBolt nut
Bolt nut for the new Rear sprocket.
It is a dedicated product and fits well.
Since it is a component that can easily come off, inspection before driving is a Large cut.
View detail
No different than OEMs
Purchased due to leaking oil line. I am glad that the quality is the same as OEM and the price is lower. I will buy again when it breaks. View detail
Tightened with a slotted screwdriver.
Used to replace an oil line. It seemed to be able to close it with a hexagon, but it didn't fit slightly. I think it is a millimeter. View detail
Fits: KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400R (-2013), KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA650R, KAWASAKI VERSYS 650
For NINJA400R
Installed on NINJA400R.
Since it is an important safety part, we asked Motorcycle shop to install it.
The feel of operation, texture, etc. was perfect without any complaints.
If you are not confident about installing it yourself, ask a professional contractor to do so.
View detail
Why is the same number of Ding as OEMs so expensive….
What made you decide to buy?
I have been working on the ZX-6R for 3 years now, and the mileage is about 10,000 km. I thought it was too early to replace them, but since all the parts were available during the spring sale, I decided to replace them.
[How was the installation?
I found information that the Torque of the Engine Sprocket nut fixing the front sprocket was halfway tight, so I loosened the Engine Sprocket nut using an electric Impact wrench from Tirefor Replacement. After that, I tightened the rear brake with the torque wrench at the specified torque of 147Nm, and finally, I bent the washer over the nut using the water pump pliers to prevent it from loosening.
*We are planning to describe this replacement work in our maintenance diary. Please take a look if you like.
How was your experience with it?
At first I was not sure whether to go with 16T or not, but I liked the ride quality of the OEM, so I decided to go with 15T, the same as the OEM. So there was no change between before and after the replacement. The normal specifications list on the product page says 16T, but the 21-year ZX-6R has 15T Front, 43 Rear, 2.866 reduction ratio, and 112 Chain links.
View detail
Bolt hole in rear sprocket is Large
It is cheap and good, but the only thing that bothers me is that the Bolt hole on the Rear sprocket is Large. I'm worried that it might move during use. View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
Fits: SUZUKI ADDRESS110, SUZUKI V-STROM250, SUZUKI GSX250R, KAWASAKI VULCAN900Classic, KAWASAKI VULCAN900Custom, HONDA LEAD125, HONDA PCX150, HONDA PCX, HONDA CBF125, HONDA CB125F, SUZUKI Address125, SUZUKI Gixxer, SUZUKI swish, SUZUKI Swish LIMITED, YAMAHA BOLT, YAMAHA BOLT Shoulder Bag RSpecifications, YAMAHA GRIZZLY700FI, YAMAHA SCR950, YAMAHA GRAND MAJESTY, YAMAHA MAJESTY250
NGK IRIDIUM is the best spark plug for the Honda Grom
These NGK IRIDIUM are simply the best spark plug for the Honda Grom! The NGK CPR7EAIX-9S IRIDIUM spark plug is a cooler plug than the OEM version that comes on the Honda MSX/GROM, it's better if you spend a lot of time with wide open throttle (like lots of freeway riding), besides that, it has superior longevity, better ignition and improved fuel economy. Overal, it's simply the best plug for the GROM and Webike sells them at a very good price also! View detail
Shorter levers
I still wonder till today why so many bike companies use the ugly, cheap looking levers in one colour only. Or no colour to be precise. Fortunately there are plenty of levers to choose from. I chose these shorter with adjustable position on both sides. They look great, the instalation was easish :) Brake is easy, clutch is a little tricky, but that applies fro any clutch where you need to fit the knob on the wire inside the lever. But anyone can do it with a little bit of patience. View detail
Fits: HUSQVARNA TC 125, HUSQVARNA TC 250, HUSQVARNA TE125, KTM EXC, KTM EXC-F, KTM SX, KTM SX-F
Great replacement clutch lever
Best lever on the market,Buy one of these levers,Looks great and functions flawless. you will remember my words when you drop your bike and race because of a broken OEM lever.Durable levers, bike cartwheeled 4-5 times and the levers only had minor scuffs. View detail