Reviews
Fits: HONDA CB1100, HONDA CB1100 RS, HONDA CB1300SB, HONDA CB1300SF, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP
General Slider
The car was delivered with DAYTONA's Engine Guard installed.
Because I scraped it just by driving normally on a mountain road,
Changed to Slider.
I am concerned about Damage to the Motorcycle in the event of a fall.
View detail
Fits: SUZUKI V-Strom650 L2, SUZUKI V-Strom650, SUZUKI V-Strom650 XT, SUZUKI DL650 V-Strom, SUZUKI V-Strom650 L2 XT
Engine Guard installed
Installation should not be a problem if you have some knowledge of maintenance.
An Engine Guard was added to protect the engine in the event of a runaway and to mount the Fog Lamp.
View detail
Looks GOOD??
It looks GOOD.
I think it is stronger than without it, but I don't know.
The price is a little high.
View detail
No instruction manual included
There is no instruction manual. The collar and bolt are confusing, or rather, wrong. The "right side, left side" in the product description photo is "right side, left side" from front to back. The 150mm bolt and 68mm total collar are installed on the left side of the vehicle. The 115mm bolt and 33mm total bolt are on the right side of the vehicle. The tightening torque is 35 ft.lb. It was able to be installed properly on the American specification 451cc Eliminator. There is no instructions come with it. 150mm bolt and 68mm (55mm + 13mm) collar are for the left side. 115mm bolt and 33mm (20mm + 13mm) collar are for the right side. Tightening torque is 35 ft.lb. They fit Eliminator 450 and 500 too. Enjoy! View detail
Works like a skid plate should
Installation will require only 5mm bolt. Color match is wonderful for bike. Immediately took this to a local trail to test it out and managed to slam it on some rocks. Held up great, took a bit of damage but that's what it's for! Its tough but it's still plastic so I'm sure it has its limits.something to protect the finish on the frame and keep the mud off the motor.Little to no gaps, excellent coverage of major components.You will need to remove this skid plate when you change your oil.But if you are a little lazy about your oil changes, this may not be for you.This is the perfect solution and was reasonably priced. View detail
I think it's a little too Large.
The Cowl is easy to install because there is no modification, it is cheap to work with, and it is very helpful for the Large size change. View detail
Custom look
It is recommended to install at the same time as the engine slider.
How does it improve the performance of the Motorcycle? But this alone will give you a great sense of customization.
View detail
Fallen cannibals
The system was installed to reduce damage to the vehicle body and engine in the event of a standing accident or a fall.
It gives a sense of overhang and security.
View detail
It certainly works.
Looking at the frame structure of the NINJA2 Helmet 50/400, it seems to me that the Left Side conectoplate is intentionally made weaker by bending it. It is my imagination, but it may be that the torsion of the frame improves mobility. The claim is that the Damper will absorb vibration and provide straight-line stability by restricting the movement here.
As it was, the ride quality was not good, so I weakened the front and rear Suspension settings by about 2Click, which I think improved the driving stability without worsening the ride quality.
I am a dull person who cannot tell the difference with a slight change, but I can certainly feel the change. It may be too much to say that the driving has become more luxurious, but I feel a sense of stability.
I am tuning the front and rear suspension with Technics or NITRON, but if you put it on a vehicle with Normal suspension, I think the original uncomfortable ride and thrust will be emphasized. However, if you use NINJA2 Helmet 50/400, it may be good for those who don't feel bad ride quality.
View detail
Fits: HONDA CB1100, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA X-4
K-Factory rear shock slider
Ok so I was expecting the slider to be bigger than it was so not sure it will offer much protection,I can say that the product is well made and looks nice when fitted View detail
![[IDEAL] Swingarm Stand Hook](https://img.webike-cdn.net/catalogue/11500/006-S0801bkb_TS.jpg)
Fits: Others , KTM 1190 RC8R, KTM 1190 RC8, HONDA CBR954RR, HONDA CBR929RR, HONDA CBR1000RR, HONDA CBR1000RR-R, HONDA CBR1000RR-R SP, HONDA VTR1000 SP1, HONDA VTR1000 SP2
Casual Dress-up
For Front Axle Slider and Engine slider
I have Babyface on and a Stand Hook.
The same Manufacturer is used for this product.
View detail
It protected me from standing moss.
I had the same thing installed when I purchased the vehicle. It was not the original purpose of the Slider, but it helped. I only replaced one of the sliders. When I was replacing it, I was playing with the one I had installed and the Black Anodized was peeling off. .... How is it in terms of quality? I feel like I have to ask myself, "How is the quality of the product?" But there are not many other options for this type of car. I just hope I won't have a chance to replace it next time. I am very happy with the quality of the product and the points it comes with. View detail
Wide range of Guard
It is more solidly built than I had expected, and my imagination that it was just a plastic board was betrayed in a good way.
Installation is easy, as only four screws are needed for installation.
I think it is better to install it after Grease up well because the screw holes are likely to be rusted by water in the location.
Since it covers the underside of the Crankcase, I think the construction is quite promising in terms of Engine protection.
View detail
Can also be installed on SUPER CUB110 JA59
Installed on SUPER CUB110 JA59.
The work itself can be easily installed with no problem at all, but it is too long for the SUPER CUB and the body will stand up a little.
View detail
Custom
Items we do not want to be indebted to you.
The appearance of custom feeling will be increased.
View detail
Fits: KTM XC250, KTM SX250, KTM XC300, KTM SX300, KTM EXC-W250 TPI, KTM XC-W250 TPI, KTM EXC-W300 TPI, KTM XC-W300 TPI, HUSQVARNA TX250, HUSQVARNA TX300, HUSQVARNA TE250i, HUSQVARNA TE300i, GASGAS EC250, GASGAS EC300
For Chamber and body protection
I installed it on a GasGas EC250 2023, which I always use for forest road touring.
Installation was quick and easy with Bolt On.
If you put on this product, which is a combination of Under Guard, Link guard, and Chamber Guard,
It protects the body of the car well even if it is slightly unBrown.
Recently, I have been interested in the world of hard enduro from forest road touring, and I have been riding in streams with large rocks,
The number of opportunities to run in gullys is increasing, and with Peetec's Guard attached, there is no chance of damaging the engine, chamber, body, links, etc., even if the vehicle is unbroken.
The only drawback is that mud and leaves can get into the Guard.
This could be improved to a Large width by machining a thin aluminum plate to prevent mud from getting in.
With this level of protection, I feel that the 40,000 yen expense is justified.
View detail
Cost-effective
I hope you don't have to deal with this product, but first of all, the installation only takes 10 minutes to remove and replace the Bolt. I have no problem with the quality, and it is the first component I install before I start riding my motorcycle. View detail
Fits: KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2, KAWASAKI NINJA H2R, KAWASAKI Ninja H2 SX SE, KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2
SPEEDRAMaterial:Twill Weave Carbon glossy Drive chain guard
The installation was not particularly difficult and was done by replacing the OEM.:Twill Weave Carbon shiny and looks up, the shape is more rounded than OEMGuard. View detail
Even a custom novice could install it.
I installed this product on a CT125 JA65, and although I am new to customization, I was able to remove the existing frame and install this product without any trouble. Although the Instruction Manual mentioned that there is an upper and lower joint frame, it was difficult for a layman to understand the diagram for distinguishing between the upper and lower frames. It was difficult for a layman to understand the diagram for identifying the top and bottom. I thought that only a person who could read drawings could understand it. Apart from my impression of the product, I was also not impressed that I could finally buy the product more than three months after each Site listing began. View detail
Fits: HONDA REBEL250, HONDA REBEL250S EDITION, HONDA CL250
I'm almost satisfied.
Exhaust system was changed from front pipe to MORIWAKI.
The vibration and other factors had already been improved because of the replacement of the
Frankly, it was hard to tell the effect.
Speed at which strong vibration occurs at high speeds is 3 to 5 km/h
I think it has grown.
I definitely felt that the rigidity of the Frame was slightly increased.
I have seen the video etc., and it has a very good reputation.
The more novice you are, the less likely you are to expect too much.
I am sure we will see the effect after long-distance, high-speed driving, etc.
I did the installation myself, but it is definitely better to have a store do it for normal people!
There is a high TorqueBolt attachment and removal of Engine Jack-up and Engine hanger bolt.
There is Torque management, and a reasonable selection of tools, including a hexagonal box wrench,
It would be difficult without knowledge.
As for the look, it is very good as it attaches to the lonely Engine surroundings.
It would be better if there was a Plating Specification or something like that.
View detail