Reviews
Fits: HONDA SUPER CUB 90, HONDA SUPER CUB 70, HONDA SUPER CUB 50
Useful in Touring.
It is useful when Rear Carrier alone does not cure the problem.
It also has a dress-up effect
good point
Instruction Manual is easy to understand.
Fit without feeling like an afterthought.
Tent can be loaded at all.
Parts rigidity is also high.
View detail
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
Large recommendation for CUB for Touring
Rear suspension is available from various manufacturers and helps to improve the ride quality, but when it comes to for front suspension, there are not many options.
This product is a Reinforcement Spring, and it is exactly what I was looking for. It is a strong ally for long distance touring.
It's not a heavy load, but it's stable when driving (but not limited to) when loaded with cargo, and it's unobtrusive and sober.
I bought the Spring and replaced it myself. I only bought the Spring and replaced it myself, but if you are not comfortable with the work, you can ask Moldy to do it for you.
They'll do it.
View detail
Fits: HONDA CHALY, HONDA MONKEY, HONDA CUB90
Design is good
This is a Recommendation because it is cheap, easy to work on and easy to ride. View detail
Fits: HONDA MONKEY, HONDA GORILLA
I'm ready to step up to the plate.
When I changed Rear to Other Brand Product, I was worried about the weakness of Front, so I introduced this one.
Compared to OEM, I think it has a little more tread to it.
View detail
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
Front stiffness is increased.
Because NORMAL was too soft, and there were a lot of near-misses such as the road surface Gap.
I decided to go with a stronger suspension, so here it is.
good point
The stiffness is increased by about 30%.
The car will not be shaken by the Gap on the road.
Reasonable price.
A bad point
The front suspension is located at the back of the car, so it is difficult to install and remove.
The installation was Large strange, but the effect is perfect.
You will be rewarded.
If you're riding a long way, road Gap and all, the original suspension feels scary, so if you have those complaints, RECOMMENDATION!
View detail
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
Resistant to rust
I used to use the Plating type, but it rusted and I bought this product! View detail
Increased loading capacity when camping touring!
Since I replaced my CUB110 with a JA44, I also re-purchased this Cuby Front carrier.
I bought the Repeat because I had used it for my previous JA07 and was satisfied with its shape and loading performance.
It is just the right size for loading Schlafsacks and Tents for camping tours and has a hook for stable loading.
When you don't have any luggage on board, the weight may increase a little, but it is not so much that the handling is worse. As expected of the CUB specialist, Cuby has thought this point out very well.
But I use it on my daily commute to work and it rusts in the rain.
This is an inevitable part of the Material, but it's a hassle to maintain, so I'm leaving it as it is.
Anyway, my belief that the best choice for CUBs is Cuby's products is unquestionable.
View detail
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
It's solid, but the Balance is a Large thing!
Fluffy feet will be Snap and used impressions. Balance and balance is still bad because I rear suspension is still NORMAL; hell; I prefer to be installed after the conversion of the rear suspension is also mandatory to be understood beforehand. I installed it by myself. I did the installation by myself, but I tried to do it with reference to Net without the Spring compressor, but it was very large and strange; (Unless you have a spring compressor.)
The price is cheap, so it's in Recommendation.
View detail
Fits: HONDA SUPER CUB 90, HONDA SUPER CUB 70, HONDA SUPER CUB 50
For CUB's CampingTwoCustom
It has a Loader Hook, and you can pack it with a loading net and rubber ties.
It is more convenient than the Basket because you can load more freely.
Be careful not to overload the Handlebar as it will make the Handlebar operation heavier and may pop out when you turn off the Handlebar.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I'm normally attached to it.
Installation was normal, I think it would be a good idea to replace it with the front fork OH.
This is the price, but you can clearly see the difference. The difference is very clear.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
Large satisfaction with excellent stability
Normal look is what I'm obsessed with, but for the 88cc engine, it's Normal The fork is still unstable
I found this product when I was looking for reinforced parts for driving stability
How did you feel after the exchange? "Outstanding stability It was
I'm really happy with the enhancements without ruining the look I chose the OEM Length, but I also have a choice of lengths, so I stuck with the Normal look I really recommend it to anyone who is
Spring replaced it himself, but I'll review the work
You can find out how to exchange it on the Net
MONKEY OEMFront Fork Spring Replacement
You can check a lot of things by searching for
We recommend replacing the following parts at the same time, as they are almost all Rose The part number is the OEM product number
Quantity:2pc. Each set is required
?ForkGuide (Part #:51502-045-670)
Dust Seal (Part #:51503-165-003)
PistonSlide pipe (Part #:51507-098-000)
?PinSpring (51526-098-000)
? , ? is Quantity:This is the one in the 1pc. eye photo
I bought these two at the same time as Spring
However, in the process of roasting, the plastic bottle broke off (see the third picture) and I had to order more in a hurry I had to order more in a hurry (the third picture)
? looked like it could be reused, but I didn't want to make another mistake, so I decided to replace it with them
Even on the Net? It is a good thing that I was able to get a good idea of what was going on, because I thought that I was going to be able to get a good idea of what was going on
I ended up having to wait a few days for the second picture
One of them didn't break, but it was pretty degraded, so I'd recommend buying it from the beginning It is
Spring is Quantity:1 Set of 4pcs. it installs to wrap around the parts in the eye picture, but
Check the inside and outside of the fork to make sure it is facing the right way
Install the spring while adjusting the orientation
A similar part will be attached underneath the Spring, but you'll have to check the direction of the pin holes to make sure it's facing the same way Install
Quantity:1 Set of 4pcs
Once the Spring is assembled, grease it well and restore it
There are many different types of grease, but I used a generous amount of Urea grease to restore it! It was
I hope you will join us
It takes quite a bit of time to do the work carefully, but I am satisfied with the changes after the replacement
View detail
Fits: HONDA MONKEY, HONDA GORILLA
Large satisfaction with outstanding stability
Normal look is what I'm obsessed with, but for the 88cc engine, it's Normal The fork is still unstable
I found this product when I was looking for reinforced parts for driving stability
How did you feel after the exchange? "Outstanding stability It was
I'm really happy with the enhancements without ruining the look I chose the OEM Length, but I also have a choice of lengths, so I stuck with the Normal look I really recommend it to anyone who is
Spring replaced it himself, but I'll review the work
You can find out how to exchange it on the Net
MONKEY OEMFront Fork Spring Replacement
You can check a lot of things by searching for
We recommend replacing the following parts at the same time, as they are almost all Rose The part number is the OEM product number
Quantity:2pc. Each set is required
?ForkGuide (Part #:51502-045-670)
Dust Seal (Part #:51503-165-003)
PistonSlide pipe (Part #:51507-098-000)
?PinSpring (51526-098-000)
? , ? is Quantity:This is the one in the 1pc. eye photo
I bought these two at the same time as Spring
However, in the process of roasting, the plastic bottle broke off (see the third picture) and I had to order more in a hurry I had to order more in a hurry (the third picture)
? looked like it could be reused, but I didn't want to make another mistake, so I decided to replace it with them
Even on the Net? It is a good thing that I was able to get a good idea of what was going on, because I thought that I was going to be able to get a good idea of what was going on
I ended up having to wait a few days for the second picture
One of them didn't break, but it was pretty degraded, so I'd recommend buying it from the beginning It is
Spring is Quantity:1 Set of 4pcs. it installs to wrap around the parts in the eye picture, but
Check the inside and outside of the fork to make sure it is facing the right way
Install the spring while adjusting the orientation
A similar part will be attached underneath the Spring, but you'll have to check the direction of the pin holes to make sure it's facing the same way Install
Quantity:1 Set of 4pcs
Once the Spring is assembled, grease it well and restore it
There are many different types of grease, but I used a generous amount of Urea grease to restore it! It was
I hope you will join us
It takes quite a bit of time to do the work carefully, but I am satisfied with the changes after the replacement
View detail
Fits: HONDA MONKEY, HONDA GORILLA
OEMFork is changing radically!
Although I'm sticking to the normal look, I'm not sure if it's possible to run the 88cc engine on the Front The fork was poor and I bought it for driving stability
It works great! The ride was so stable that I wondered what it was before I chose the OEM Length, but I also chose the Normal Length because the price is cheap If you're obsessed with the look, I would highly recommend it
I'll include the points of my replacement
I hope you will make it a point to join us
How to Exchange
There are not many ways to replace it, but it is introduced on the Net, so if you refer to it, the work is not so bad It's not difficult
However, the parts to which the spring is attached (the parts on both ends of the spring in the second picture) have different orientations When restoring it, check the inner and outer sides of the fork and adjust the direction of the hole and protrusions Install the spring
The part that attaches to the top of the spring has a protrusion on the inside that indicates its orientation Quantity:(1 Set of 4pcs. eye photo)
Parts
I recommend Overhaul while you're at it, as I'll lose almost all of the Spring exchange It is
The OEM Parts part numbers are listed in the Join section
Dust Seal (OEM Product No. 51503-165-003)
?ForkGuide (OEM Product No. 51502-045-670)
PistonSlide pipe (OEM Product No. 51507-098-000)
PinSpring (OEM Product No. 51526-098-000)
Quantity:2pc. Each set is required, so please pay attention to the quantity when ordering
? and ? Quantity:These are the parts in the 1pc. eye photo
? and ? I bought it in a hurry because it broke when I lost Fork There was an introduction such as the crack in Net, but it was thought to be Large sturdy, but as expected It was cracked, and it was also quite deteriorated …^^;
? and ? will have to wait for the state of the second picture if you don't receive the ? Recommendation
? looked like it could be reused, but I didn't want to make another mistake, so I made a new one just in case
Grease!
I selected Urea grease
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Battle at price
The installation has been done a few times with Gorimont FFork Parts Replacement Grease Replacement, so It's easy to remove from the Fork and divide it into two parts, but this is the first time I've removed the Fork Spring So when I watched Net and grabbed the game, I was grilling between the Vise and the Vise, and it didn't just miss, it went on and on I couldn't help myself, so I used a sander to cut it off I put it on the Vise stand and realized it was Opposite Thread Screw, so the second one was I managed to remove it with a lot of force
Installation is done in reverse order and then you can put the Grease to Quantity:Pair (for Left and Right) You can paint it in evenly (I make sure to apply the Grease so that no air gets into the Spring place every time I'll put it in.)
I grabbed the FBrake to see how much spring pressure I could get before the ride, and then I moved it up and down I felt it was quite hard, but there is no feeling of rattling at all when I started riding There is no NORMAL Full Bottom and no pompom when Brake is on (By the way, I installed an absorber on One Side.) I was able to drive my MONKEY at 60km with the Pi Pass as it is a second class Number The braking is now better than the NORMAL Plus Absorber
One last word, Moldy's packaging was very clean and Bigli
View detail
Fits: HONDA MONKEY, HONDA GORILLA
The price is good
I replaced them together when I did the Front forkO/H on the AB27 PartsForkGuide, Pin, Dust Seal, C-ring, C- ringWasher, buy the slide pipe and start to work It took me about 15 minutes to make it, but I put it between the Vise and the normal spring to remove the normal spring and turned it the wrong way It takes a long time, and finally, you can't take it even if you turn it, even if you hit it, so you can't get it off with Leutor After removing Normal spring, I used CubyReinforcement I put Spring in and then applied Grease with Fully, and then the reverse when I removed it If you put it together in Pattern, you're done, and by the way, it was really easy to incorporate
The first thing I thought about when I installed it was A - before driving, I put the front brake on the front fork to raise and lower the front fork I'm glad I put Grease in with Fully, which is hard anyway when I did the B-Running feeling is the squishy feeling of Normal spring (No Steering Damper) It is C-8InchTire that will be gone, so until now it is adjusted with Steering Damper It has become better to run it plus
Finally, the packaging is better than some of the companies that deal with CHINA, and Cuby's If there's something I want in a product, I'll buy it on the spot
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
It's very useful with a little extra work
I installed it on a Bore up LITTLE CUB 88cc
This one, though, is a cheap exhaust system
Maybe Cub Muffler, excluding Copy products, is webike1 cheaper?
It's cheap, but you can find it on the website of the famous Custom ShopMoldy in the CUB world I bought it because I thought it was reliable
[Structure]
Quantity:1 Set of 3pcs.Spec
The OEM CUBs are also integrated, and the external ones are usually large and integrated But if the CUB is bored up and running hard, it will resonate and break It was a mess at the end of the day
Probably because the Mount position is the Body Center and Silencer is extended behind it for a long time I think that was the reason I'd like to think it was the reason why Mizumoto broke
So this 3-Piece Structure was a wishful thinking
【attachment】
If you have a basic skill, you can afford to replace it yourself
Although the possibility of large-volume production cannot be denied in terms of price, it is Level As far as I'm concerned, Mizumoto RACING had a much harder time
[Running]
In the case of Baffle, there has been no drastic change from OEM
I've become a complete Style watchdog
But it didn't sound too loud and that was a good thing
Without Baffle, it's too loose and it's a blast Probably, the bottom is also scuffed
As a result, I had to drill holes in the Baffle and struggle to find the right amount of slack But it's cheap, so that's good!
[Others]
This is a cheap product, so I want people to use it if they can figure out that it's something like this There was a point
? Minimum ground clearance is too low
Maybe it was originally for MONKEY or something, obviously too low exhaust for a CUB I became Shaco Tan by handling the pipe
With LITTLE CUB, it feels like rubbing underneath when you enter Convenience
If you hit it too hard, it will kill Stud
Oil can't be replaced
Not being able to do it is an overstatement, but it's hard to do
What I mean by that is that the exhaust pipe goes right under the drain, so you have to take out the oil It takes just a few minutes
So if you ask me if I should remove the exhaust pipe every time I change the oil, I won't, because it's too much trouble
It's a bit of a hassle to solve, but I'm going to put Corrugated cardboard in it and put Oil on top of it Create a system that feels like the flow of
Someone's having trouble with the Brake pedal
I installed various external exhaust systems, so it was already taken care of, but the CUB Brake The pedal interferes a little bit
If the Pedal is positioned too high, you can use the color You can add a Don't forget to adjust the Brake after you do it
Owner's touch on the cheapest thing is the Large thing
View detail
Fits: HONDA Super Cub 70, HONDA Super Cub (HA02), HONDA Super Cub (C90 type), HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub]., HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub].
Cap Nut & Washer for Honda Super Cub
I purchased this set of stainless steel bolts and washers to replace old original parts that were corroded and badly worn, the quality of these parts turned out to be very good, the stainless steel is thick enough to withstand the required forces. The installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for the fast delivery and great packaging! I purchased this set of stainless steel bolts and washers instead of old original parts that were corroded and worn out. The quality of these parts turned out to be very good, stainless steel of sufficient thickness to withstand the required effort. Installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for fast delivery and excellent packaging! (Translated by Google Translator) View detail
Fits: HONDA CHALY, HONDA MONKEY, HONDA CUB90
Good Cost performance
The exchange from OEMfootpeg, custom made Appeal feeling is good. By the way my own LITTLE CUB, because the body is vibrating so much I wore a tightening Bolt on the back of footpeg with a screw lock with a loose stopper. View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
interference
It installed in SUPER CUB 90Custom.
Although it is also in Review of the other person, it interferes with Brake Arm.
Although I could install without interfering if I bent Bracket and Exhaust pipe by hand slightly, but one anxiety remained.
Large stands as it is with Center Stand, but it also interferes somewhat like this when parking in Center Stand.
If you do not remove Center Stand, I think that parking with Side Stand is as good as possible.
Is it reasonable to think at this price.
If you say the perfect ones, say, Recommendation of another company's Exhaust System.
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
Cospa best!
C50 (49cc HeadTune car) I am using it.
Although it is touched with for CUB, Layout itself is the same as for MONKEYDown Exhaust System passing under the Engine.
This will reduce the clearance to ground, but for Kick pedal for MONKEY can be used and custom choices will increase.
It is impossible to imagine building around 10,000 yen in a good way.
The fitting of the Exhaust pipe is almost perfect, the welding is also beautiful, there is no excitement of the Bead inside the Flange.
Since there is no fancy yet, it is not suitable for those who want the Impact of the appearance.
Although it is the performance aspect of the essence, this also betrays expectations in a good meaning.
Except that Setting is a little difficult and the lower Torque is slightly thinner, it is a fun Exhaust System that can be used for Almighty from town to pass.
The volume is modestly modest in Down Type's Exhaust System, but if you compare it with NORMAL, you are still quite noisy, so be careful.
It may be a problem of individual differences, but the length of the attached Spring may not match, so it may be necessary to prepare separately.
Also, the Exhaust pipe has passed through just under the Drain bolt, Oil is applied every Oil change and the cleaning is Large strange.
Although I can not help to say that the price is suitable if I look at the details, I think that it is an excellent gem for Cost performance even in that case.
I want to make it an external exhaust system but I do not want to be so picky, it is recommended for those who do not want to spend money there.
View detail