Reviews
Older cars with Cowl, note dimensions.
In the 80's and 90's Racer replicas, the Meter area was designed with a Horizontal Type MASTERCylinder, so there is a high probability that when the Handlebar is turned to the Left, the base of the Brake lever will contact the Meter, causing not only the Front brake to fail, but also the Handlebar Lock to fail, This will not only cause the front brake to be inoperative, but also disable the handlebar lock.
BrakeTouch itself is no different from the Horizontal TypeMASTERCylinder and Large, but the controllability is a little better.
After using it for a while, I may revert to Horizontal Type if it seems to offer few advantages.
View detail
Fits: HONDA CBR400F, HONDA CBX750F, HONDA CB1100F, HONDA CB1100R, HONDA CB900F, HONDA CBR1000F, HONDA CBR600F, HONDA CBR750, HONDA VF400, HONDA VF750F, KAWASAKI KR-1/S/R, KAWASAKI Z750FXII/III, KAWASAKI ZR-7/S, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZX-7R
Perfect for dress-up!
The dress-up effect is great.
It also feels right in use.
View detail
Fits: YAMAHA Cygnus X SR, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, HONDA XR230, HONDA XR250, SUZUKI VX800, HONDA SL230, HONDA PCX150, HONDA PCX125, HONDA NSR80, HONDA NSR50, HONDA NSR250R, HONDA NSF100, HONDA NS50F, HONDA MBX80 Integra
Matching with Caliper
Purchased a 1/2-inches diameter short lever to replace the front caliper with a Brembo crab caliper.
Piston diameter 32mm in combination with Caliper (hydraulic pressure ratio 6.35) is
No Control at all with stiff Touch.
Piston diameter 34mm in combination with Caliper (hydraulic pressure ratio 7.17) is
Good Controllability, although a little softer than the preferred Touch.
If it were a standard Lever, would the former combination have been acceptable?
View detail
Fits: YAMAHA ZEAL, YAMAHA YZF-R7, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA XJR1300C, YAMAHA XJR1300, YAMAHA XJ400, YAMAHA TZR250, YAMAHA TZR125, YAMAHA TMAX500, YAMAHA TDR250, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRV250, YAMAHA SR500, YAMAHA SR400, YAMAHA SR400, YAMAHA RZ250, YAMAHA RD400, YAMAHA FZR250
Original Japan Daytona x Nissin 14mm axial . Took 3 days to arrive to Singapore from mailing date .
Easy bleeding during installation . Upgraded from 11mm to 14mm axial. Love the lever feels. Installed on Yamaha Vixion-R 155 . View detail
Fits: YAMAHA Cygnus X SR, HONDA XR50 Motard, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI DR-Z400SM, SUZUKI RMX250S, SUZUKI SV400, SUZUKI GS125, SUZUKI GS125E Katana, SUZUKI RMX250, SUZUKI GSX250S Katana, SUZUKI RG200
Used for MAJESTY 125 FBrakes custom
The MAJESTY125 and R1-Z have the same 83mm Pitch of the front brake caliper, so I used the R1-Z's caliper and changed the front brake to 4POD to strengthen the brake. So, I wanted to lower the Piston size of MASTER, and I wanted to be able to adjust the lever play by Dial as well as CB1300 Caliper, and I wanted to use a short lever. I also wanted to use short lever, so I replaced it with Nisshin's MASTER.
As expected, the brake has improved in both touch and braking power due to the MASTER's smaller-diameter piston size,
Now I have a performance problem on the Caliper side and want to replace the Caliper with the SumitomoCaliper from TZr250 after 3MA or the Nisshin caliper with 83mmPitch released from TZ125, TZ250 and AdvantageNisshin in the 90's. I'm looking for a new caliper.
View detail
Fits: YAMAHA MAJESTY250(SG03J), YAMAHA MAJESTY250(SG03J), YAMAHA MAJESTY250(SG03J), YAMAHA MAJESTY250(SG03J), YAMAHA MAJESTY250(SG03J)
MAJESTY's Brake to Quantity:Pair (for Left and Right) in exchange for
Right Side (for Front) When replacing the Master Cylinder of the Left Side, the Left Side was replaced together with the Right Side because the appearance of the Left Side in Normal is not consistent and not cool.
Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.
As with the Right Side, the OEM MASTERPiston diameter was lowered by 1 size (11mm) compared to the 1/2-inches of the OEM MASTERPiston diameter, and the brake was strengthened by the SKULL Helmet principle.
However, the Piston size of MAJESTYC's Rear caliper is smaller than that of the Front caliper, or perhaps the Left brake has a harder feel than the Right brake.
For now, I'm using the largest play size, but it's a little hard to control. (The fact that it is a Rear also makes it extra.)
Front is softer and easier to Control.
However, there are no more smallest piston diameters in this series of masters, and it is within the tolerable range, so it is used as it is.
I think it would solve the problem if the Caliper on the Rear was the same as the Front, but the cost-effectiveness is not so good, and it would cause other problems, so I'm leaving it as it is.
The Rear is also equipped with Yamaha's 83mm Pitch Caliper, so the for FrontCaliper can be attached to the Rear as well, but instead of having the same touch, the pad area increases, which increases the brake braking force of the Rear too much and causes the balance of the Rear to collapse. However, the pad area is increased, which increases the braking force of the Rear Brake too much and causes the Rear to lock easily.
View detail
Fits: TRIUMPH LEGEND TT, TRIUMPH ADVENTURER, KAWASAKI KSR110, KAWASAKI KSR-2, KAWASAKI KLX250SR, KAWASAKI KSR-1, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX125, KAWASAKI KLX250, KAWASAKI KLE400, KAWASAKI KDX250SR, KAWASAKI KDX250R (for competition), KAWASAKI KDX220SR, KAWASAKI KDX220R (for competition), KAWASAKI KDX125/SR, KAWASAKI D Tracker 125, KAWASAKI D tracker, KAWASAKI 250TR, SUZUKI Address V100
Replace instead of overhaul 20 year old OEM
The MAJESTY 250 OEM Master Cylinder is 20 years old, the paint is peeling, the fluid level window is white and cloudy, and the touch screen is dead. I thought that if I replaced it with OEM, it would be in the same condition again someday, so I replaced it with this one, which has better accuracy and quality.
The original vehicle had some customization done to the exterior, and the replaced handlebars gave it a more custom look.
I am satisfied that the color of the handlebar matches the color of the MASTER and Lever, creating a sense of unity.
Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.
Also, we are happy to be able to strengthen the brake with the SKULL Helmet principle by lowering the diameter by 1 Size to 11mm, compared to the OEM MASTERPiston diameter of 1/2-inches.
The brake hoses were stainless steel mesh when they were installed, so we did not have to worry about a large increase in stroke volume, and both control and braking power were improved, resulting in a highly satisfactory brake customization.
View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Brake's Stress is reduced.
This is a change from OEM horizontal placement 11mm to 5/8Radial master.
Because it seemed to interfere with the Switch box, the Lever was changed to Eukanaya's (NI002-049),
Nisshin's Tank Bracket (49151) for Separate Handlebars is installed.
As for the banjo fitting, a stainless steel mesh hose (AC Performance line) compatible with the car model was originally installed, but it interfered with the switch wiring, so an L-shaped adapter was used to make an escape.
My impression after installation is that the absolute braking force has not changed, but the controllability has improved.
Specifically, it is an Image with interpolated increments of braking force according to the strength of the grip.
The beginning of the grip is especially noticeable. With the horizontal 11mm pad, the rise in braking force is abrupt, but with the vertical pad, there is a sense of being able to adjust the strength of the pad. The same is true near the end of the grip, making it easier to generate strong braking force without locking.
Probably because the lever ratio and diameter are designed to match the weight of a horizontally mounted 11mm lever, it will not be that uncomfortable (too effective or too ineffective) to replace it. If you want a lighter grip or more strokes, you may want to consider a 14mm or 15mm model such as the F Land-.
In general, I can recommend it, but since it is Large strange to do banjo fitting by yourself, it is safer to ask a supply store with a Pit.
View detail
Fits: HONDA AX-1, HONDA CB-1, HONDA CB400SS, HONDA CBR250F, HONDA FTR223, HONDA FTR250, HONDA GB250 Clubman, HONDA NC700S, HONDA NC700X, HONDA NC750X, HONDA NS-1, HONDA VT250 Spada, HONDA VTR250, HONDA jade, YAMAHA DT200WR, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA RZ50, YAMAHA SDR200, YAMAHA TDR50
New Master Cylinder while replacing Lever.
[How is it used?
The Yamaha MT-25's Brake lever had been made in China since delivery and I was concerned about rattling.
I was worried about using such a product in Brake, but I was wondering what to do because OEM products are too expensive and other brand products from proper manufacturers are expensive. I was wondering what to do. I realized that if I just refurbished the Master Cylinder, it would solve everything, and I came across this product, which is a NISSIN product with a separate tank.
Was the one you received as per Image?
I have used a different Master Cylinder diameter on a different car model, so it was as per Image.
Was the installation difficult?
In the case of MT-25, of course, there is no need to consider interference with Cowl, so it is almost a simple installation.
The banjo bolt was left in place, and the brake switch was simply replaced since the terminals are exactly the same.
In my case, I had a hard time getting the air out because I had changed to Separate Handlebars.
How was your experience with it?
The OEM and Piston diameter is the same 11mm and the same sideways push, so we did not feel much change in the touch and effectiveness of the Brake.
However, with Lever's new, crisp and accurate, I feel that my peace of mind has increased many times over.
Also, NISSIN Lever's R condition etc. is so exquisite that my fingers do not get sore at all even if I ride for a long time.
It looks better and Repair Parts are readily available, so there is nothing to say about it.
[Included Parts:were they on?
Basic AlmostQuantity:It is a Set, but the Mirror Holder Bolt for M10Pitch 1.25 does not come with it.
Perhaps the M6 Tank fixed Bolt is a mistake.
It just so happened that the original Mirror Holder cap had the same cap, so I was able to use it and get away with it.
[Was there anything that disappointed you?
Not particularly
【Review】
Quantity:Pair (for Left and Right) It is great to be able to refresh the Master Cylinder for about the price of a Lever set.
Anyway, it is very reliable and has the best Touch of Lever and even Adjuster.
I have graduated from the mysterious Chinese Lever and can now ride without hesitation.
View detail
Fits: YAMAHA Cygnus X SR, HONDA XR50 Motard, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI DR-Z400SM, SUZUKI RMX250S, SUZUKI SV400, SUZUKI GS125, SUZUKI GS125E Katana, SUZUKI RMX250, SUZUKI GSX250S Katana, SUZUKI RG200
Good product
Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
Parenthesis good!
I bought it because I wanted to have the same type of Brake and Clutch. View detail
Fits: HONDA CBR400F, HONDA CBX750F, HONDA CB1100F, HONDA CB1100R, HONDA CB900F, HONDA CBR1000F, HONDA CBR600F, HONDA CBR750, HONDA VF400, HONDA VF750F, KAWASAKI KR-1/S/R, KAWASAKI Z750FXII/III, KAWASAKI ZR-7/S, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZX-7R
NisshinBrake master cylinder kit (Horizontal Type)
I wanted to finish bleeding the air out of the brake fluid in one go, so I replaced it together with the brake hose replacement. The touch of the brake also worked better than before, and I am satisfied with the large change. I recommend everyone to dress-up the front area! View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI ZX-10R, KAWASAKI ZX-6R, KAWASAKI ZZR1400 (ZX-14), SUZUKI GSX-R750, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA1000 (Z1000SX), Others
Buy it to put on gsx-s750 abs 2021
I buy it to replace oem master cylinder Work good beter than oem I gonna instal steel brake lines i belive it will work even beter View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
Great upgrade
I wanted to try the Nissin radial master cylinder before going and spending $$ on the Brembo set up, figuring it should work well with my nissin calipers. I can say that for $130 I am very pleased with the added performance of this part. Very easy installation, and the lever feel is AMAZING. One finger is all you need to brake at any level, with SO much more modulation. (Control of braking pressure) anyone with Nissin calipers I would highly recommend getting a set, well worth every $ View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
Radial brake
Replaced DAYTONA's ?-type Master CylinderBrake with a Radial master cylinderBrake.
I heard that Radial is easier to operate than the ? type, so I wanted to try it out to see what it would be like.
After the replacement, I went touring and tried it out. Compared to the ? type, it works as much as I grip it, which makes it more controllable.
The grip also feels softer.
Since engine braking is difficult in 2-stroke engines, the Brake, which can be activated as much as you hold it, suits me well.
View detail
Fits: Others
Brake master is a good cosmetic and quality product!
Black Lever's Type was installed on DUCATI's 900 M.H.R.
The MASTER on the Clutch Side was faulty, so we made this one Radial, so we made the Brakes matching as well.
The previous MASTER was a Tank-integrated MASTER that appeared to be OEM, so the improvement in functionality is obvious.
I just replaced it and haven't used it a lot yet, but I could sense the Touch's quality and Direct feel.
Fluid tanks are [Color] I also like the fact that it is Smoke and discreet.
View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI ZX-10R, KAWASAKI ZX-6R, KAWASAKI ZZR1400 (ZX-14), SUZUKI GSX-R750, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA1000 (Z1000SX), Others
Installed on 2022 SV650 ABS
About the feeling of use: Stock Front Brake Master Cylinder for the SV650 is notoriously spongy feeling. After replacement, the brake feel is a lot more better. A great upgrade for a 2022 SV650 Difficulty of installation: 4/5. I bought a generic stainless steel brake cable but doesn't fit mine. I had to return my stock cable but have to adjust the cable route. About shipping and packaging: Packaged arrived secured and well pack in the Philippines. Any concerns, cautions, or advice when purchasing: Consider looking a longer brake line when purchasing this for your 2022 SV 650. View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Fitting is very severe
Purchased to install on a 2019 YZF-R25 (RG43J).
The lever angle of this vehicle is too high for me, so I wanted to adjust and lower it, but the handlebar position is too far forward for a separate handle, and the Horizontal TypeMASTERCylinder immediately interferes with the handlebar, making it impossible to lower the handlebar at all. I bought it for the purpose of adjusting the position rather than the performance.
However, for the reason I mentioned earlier, the Straight shape banjo interferes with the lever when the brake hose is passed through it, so if the angle is increased to avoid this, the lever will now interfere with the cowl when the handlebar is turned to the Left.
In the end, I bought various shapes of banjo, made a tentative match, and finally managed to match them in-kind, "Here." The only way to get to a position and angle that is "right" is to use the "right" side of the needle. The process is like threading a needle. You can do this with "Conform" I wondered if it would be okay to say "yes" to this question. If you say that the product is compatible, please at least attach a fitting diagram for each major car model.
The installation may not be a problem for other types of cars, but for this type of car, the risk is too large for beginners to DIY, so it is better to leave it to the shop.
View detail
Fits: TRIUMPH LEGEND TT, TRIUMPH ADVENTURER, KAWASAKI KSR110, KAWASAKI KSR-2, KAWASAKI KLX250SR, KAWASAKI KSR-1, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX125, KAWASAKI KLX250, KAWASAKI KLE400, KAWASAKI KDX250SR, KAWASAKI KDX250R (for competition), KAWASAKI KDX220SR, KAWASAKI KDX220R (for competition), KAWASAKI KDX125/SR, KAWASAKI D Tracker 125, KAWASAKI D tracker, KAWASAKI 250TR, SUZUKI Address V100
Braking power up by 1SizeDown from OEMMASTER
The wife of the owner of the vehicle said that she was afraid of braking due to the 20-year-old OEM Master Cylinder, so we decided to replace the OEM MASTER Overhaul with this MASTER. I also wanted to increase the braking power by reducing the size from the Piston type, so I replaced it with the 11mm Piston type MASTER. (Quantity:Pair (for Left and Right) to 1/2-inches→11mm)
The smaller piston size of the Master Cylinder increases the braking force, but the amount of stroke increases, so a change of about 1 size is recommended.
The MAJESTYC I installed is my wife's Motorcycle, and she has a weak grip, so I had a request to make the Brake a little lighter.
The touch was good, and together with the 20 year old Brake hose, which was also changed to Stainless mesh, the Brake looks very nice.
My wife was relieved to hear that it was easier for her to ride as well.
View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Huge! Big! Short! Fee Ring is not bad.
It is cheap, but this Fee Ring is just radpon!
However, the standard lever is a short lever, which is hard to handle for me as a 4-finger brake user! I replaced it with a standard lever (sold separately), and now I can handle it easily.
It looks, but it's tough! It's huge! It's huge!
As a person who used to prefer the magra195MASTER, I can't get rid of the uncomfortable feeling that it is too big and bulky every time I see it.
If you separate it from functional Parts, I don't think it is a bad thing. I plan to use it for a while.
But I would recommend HC-1 to future buyers!
View detail