Reviews
Good cupholder
t's a really good product. Both the finish and the design are excellent. Thank you for your prompt delivery. I recommend this product to others, too View detail
best cup holder
I've been riding motorcycles for about 10 years, buying and selling them many times.
This is a cup holder item that is always required.
It is light, sturdy, and has an excellent design.
Tanax is the origin of most cup holders sold in Korea.
In the photo, I mounted it on Ct125. -------------------------------------------------- -------- While riding a motorcycle for 10 years, I bought, sold, and sold it several times It is a cup holder item that is always required. Light, sturdy and design is excellent. Most of the cup holders sold in Korea are Tanax. The photo was mounted on CT125. Powered by Google Translator
View detail
Screw goes missing.
It is used with Pillion Bar.
Quality as a Holder is perfect!
It is well made and highly satisfactory.
However, the screws for adjusting the Large size may be prone to falling off.
If you don't squeeze it properly and drive with it loose, it will fall off before you know it.
Once it is lost, it is even more likely to fall off with other nut, etc. Therefore, it may be necessary to first apply Screw lock to the tip of the Bolt to prevent it from falling off.
View detail
It's not bad, but there's no outstanding ingenuity or functional beauty.
I think this is a dead feature, although it is mentioned that it can be adjusted according to the Bottle width.
The construction of the Screw part seems to loosen easily if it is tightened frequently and repeatedly, so it cannot be used extensively.
The holder is recommended to be semi-fixed with a width that allows a 500ml bottle to fit in the limit.
If possible, I would have liked to see consideration such as a strong Spring type to make it easier to adjust the width.
Also, when installing a Short Screen on a car body or near the Grip, the Tumbler of ConvenienceCoffee, for example, must be careful because the container, which has lost its contents and become light, can easily be blown away by the driving wind, effectively littering the area.
I must say that if the Holder is not able to hold it securely until you throw it in the trash yourself, it is not a very good drink holder.
I would like to see a mechanism to keep Hold on the Bottle.
Also, if the Handlebar is installed as is, it will scratch the paint on the Handlebar, so I think it should at least come with a weather-resistant rubber plate.
After about three years of use, there has been almost no deterioration, and the product seems to be made to be resistant to rust and deterioration, so the durability aspect is promising.
View detail
Used for Motorcycle Drink holder.
I bought this to replace the drink holder I had made for my KSR2 and to install on another motorcycle. (Inner?) I ran 60km without Sponge, but Plastic bottle did not fall off and I was able to use it safely.
I don't know if all of them are compatible with Plastic bottle.:The color of the Sponge is Blue in the Site description when I purchased it, but it is Black in the current Catalogue, so naturally I received the Black color.
View detail
Drink holder
I am very satisfied with the way it is made.
It is very good because it can be easily adjusted according to the Drink Size.
View detail
Satisfied Drink holder
Material:The plastic drink holder is thick and stable, and the bottle is adjustable so that it will not loosen due to vibration. The matte black color matches the color of the car body and I am glad I purchased this product.
In REBEL250, the bracket is attached to the handlebar and the holder is placed in front of the handlebar.:Set the Quantity next to the Speedometer to avoid hitting the Fuel Tank.:Set. I wish the mounting area was a little wider.
View detail
Put it on knowing it won't look good on you! Plenty of practicality!
To be honest, I think it would be uncomfortable to install it on a Full Cowl Motorcycle with a Separate handle.
The Long Screen has been replaced with a Long Screen, so it is not noticeable from the outside.
I bought it because I don't want to get on and off my motorcycle every time I suck water while touring…
The result is Large! The plastic bottle is very stable and does not fall off.
No wobbling, even with an empty plastic bottle!
I didn't think it would be this useful… I wish I'd installed it sooner!
It's Recommendation!
View detail
Very easy to use.
When I go Touring, I bring my own home brewed Coffee.
I am using an insulated Bottle of about 350ml.
Bottle is very stable on mountain passes.
One point I would like to make is this.
The bar clamp is vertically large.
22.2Φ degree, only the front and the back are in contact with each other.
Rather than being fixed by frictional force, only Bolt's tightening force
I am a little worried about where to rely on.
View detail
Speedra Drink holder
Installation was easy and I was satisfied with both the design and the quality. View detail
Convenient
It is very convenient to mount securely on Handlebar.
It can be fixed stably and will not shift while driving.
The angle can be adjusted freely, and the large, hand-cranked Screw makes it easy to install and remove.
View detail
good (quality)
American Drink holder made of leather.
The installation location can be freely chosen, so it can be placed anywhere, including around the Handlebar.
It is convenient to keep hydrated while touring by putting Drink in it.
View detail
good (quality)
American Drink holder made of leather.
The installation location can be freely chosen, so it can be placed anywhere, including around the Handlebar.
It is convenient to keep hydrated while touring by putting Drink in it.
View detail
Purchased for boat use
Drink holders for ships are very expensive.
I purchased and installed Universal Product.
View detail
No problem
Drink holders are useful for road motorcycles.
Anodized paint finish looks good and looks great on your motorcycle.
The plastic bottle also fits in the Refreshing, and the performance is fine.
The product is inexpensive and easy to handle.
View detail
Adjustments.
The mounting height can be changed, allowing for adjustment to a user-friendly position.
The width can be easily adjusted with the screw on the bottom to fit plastic bottles and water bottles, so there is no wobble when running.
Aluminum and luxury.
View detail
For CoffeeTime during warm-up
I bought this to take a break with a can of coffee while warming up for work.
Sports motorcycles don't have a lot of space for this kind of thing, so I had to worry about not interfering with the handlebar when cutting it through the mount bar.
with Adjusting Function, but it is almost fixed because it is only for the can Coffee.
After this I also installed Smartphone Holder, but when I make too much wacha wacha, it becomes inconvenient to Access to Key cylinder.
You need to reconsider Coco.
View detail
Travel with me!
I bought it so that I can rehydrate quickly when I take a break during touring.
I attached it to the webbing section on the SIDE of my REBEL 250 OEMSaddle Bag.
It was easy to install, the texture of the Nylon system was similar, and there was no complaint of any discomfort.
View detail
Road motorcycle essentials
This is a must-have drink holder for road motorcycles, easy to install and essential for touring. It is flexible, light and easy to handle. View detail
It looks great on American.
This is an American style drink holder that looks great on your Harley. The large size is adjustable for your convenience. View detail