Reviews
NS400 Carburetor rebuild
This was a really good kit shame its gone obsolete, all gasket well made and shapped to form. After a trip through the ultrasonic cleaner, final re-assembly with all new parts. Like said great kit shame its dis-continued, after nearly 40 years the original rubber parts are so hard, this kit was ideal for the rebuild. View detail
NS400 Carb rebuild
Well made part fits well with no issues, replacing the original plastic part. Finish on part is good, got the replacment rubber sealing caps to complete as the original rubber had gone hard after 40 years. View detail
Fits: HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA NSRmini, HONDA NS-1, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS50F
Overhaul
I bought this because I wanted to build parts that would improve the performance of the engine overhaul of my NSR50. The assembly is a bit large since there is some press fitting work to be done. I don't have a hydraulic press, so I'm planning to challenge with Vise.
I don't know when I will be able to ride it, but I am looking forward to it.
View detail
no problem
I am very grateful for DMR's products since OEM is not available. I was able to install it without any problems. I can't say how durable it will be.
....。
View detail
Fits: HONDA NS250R, HONDA NSR250R, HONDA NSR250R, HONDA NSR250R, HONDA NS250F
It's something that doesn't appear in OEM Parts.
This part is not available in OEM Parts, so it would be helpful if you could offer it as a product like this.
Since it is tightened tightly with aluminum, it is always a part that is deformed when overhauled, so it looks better if it is replaced.
View detail
Fits: HONDA CB400SF, HONDA CB750FC, HONDA CB900F, HONDA CBR250, HONDA CBR250, HONDA CBR250, HONDA CBX1000, HONDA MVX250, HONDA VT250F, HONDA VT250F, HONDA VT250Z, HONDA VT250Z, HONDA STEED400, HONDA VF400F, HONDA NSR250R, HONDA NSR250R, HONDA NS400R
Diversion to Honda GB500
Gasoline leakage from the Cook is expensive in GB500 because the Fuel Cock is a non-resolving Type.
Processing is required, but I appreciate that it is inexpensive and problem-free.
View detail
Very Nice Kit
Received the kit quickly and was very impressed with the quality. Some modifications required but easily done by a local engineer. Very happy with the purchase. View detail
Exchange Recommendation
OEM Parts Needle bearing can still be ordered.
I replaced it with this product after watching DMR-JPAN's video.
The engine can be replaced without dismounting the engine by draining the mission oil and removing the shift spindle.
Easily replaceable with Pilot bearing puller.
Oil seal is also included, so it is nice not to have to order separately.
I just replaced it so I don't know how durable it is.
I didn't have any difficulty in getting GEAR out or Shift in my vehicle.
We are not sure if there will be any change, but since the vehicle is over 30 years old, we recommend that it be replaced considering its age and deterioration.
View detail
Replace with new one
The new one will be replaced at the time of maintenance of the carburetor.
Quantity in 1pc. min. cheaper than HondaOEM Product:2pc. I can buy a Set, and since the performance is the same, I am replacing it with this one.
View detail
Used on NSR250. Over cool measures in winter.
It is mid-summer so I can't benefit from it yet, but I changed from Thermo-less to low temp for winter over cool measures. I wonder if I need an electric fan no matter how much I open the low temp to 50C. My cooling specifications are 140mm jungle fan. (Thousands of yen) Thermoswitch, also in the jungle, to (about 900 yen) I think I keep 71-78 degrees Celsius at the setting where the fan turns at 80 degrees Celsius when the traffic is congested at about 35 degrees Celsius in the daytime in midsummer with Thermistor sticking into Thermo Case and Radiator cap changed to 1.3, Coolant is Heat block plus.
I'm hoping to reduce the warming up time in winter.
View detail
Fits: HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50
About MechanicalSeal
Thank you for your prompt response.
I put it together as soon as it arrived. 。 Water leak cured.
I guess it's hard if you don't have a certain amount of knowledge. ??
View detail
Fits: HONDA NS250R, HONDA NS250F, HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Inexpensive and good.
Used for TA21A.
The only minor issue is that the Float Packing is a little small.
I was able to install it with no problems in use, but I'm not sure about the durability yet, so I guess I'll have to check ??3.
View detail
For maintenance above the waist of MC21
[How is it used?
I purchased this product to clean the engine piston and replace the piston ring, as well as to renew the gaskets.
Gasket and O-ring of MC21 are Quantity:It is in a set, you don't forget to buy it, and it is inexpensive.
How was your experience with it?
I was a little skeptical because of the low price, but so far the Large seems to be sturdy. But so far, it seems to be large and sturdy.
CylinderBase, Head Gasket and ChamberGasket were used, but there is no leakage.
Naturally, the size is also Exactly, and the cost was lower than with OEM parts.
How did it compare to other products?
Each Gasket is almost always available with OEM parts, but it is quite expensive to get them all, so they were very helpful.
[Points to note]
Naturally, it is necessary to ensure the prevention of misassembly and Torque management.
In addition, since we do not know which fine O-rings are for which, we have no choice but to match them with the actual ones.
【Review】
It is convenient and inexpensive to use this product for maintenance above the waist.
You only need to do your best to identify the O-ring, but if you don't have to force it to be replaced, you can keep it as a Stock.
View detail
Fits: HONDA NS250F, HONDA NS250R, HONDA NSR250R
Carburetor came back to life.
When I was doing OH on my carburetor, I couldn't find a drain bolt for Both Sides at any of the shops. I was very impressed with the Carburetor that came back to life. View detail
Can be used in the same way as OEM Product
[How is it used?
Used in Engine as well as OEM Product
How was your experience with it?
I have no problem at all using it.
How did it compare to other products?
I was not sure about the steel one, but I'm glad I went with this one.
[Points to note]
For installation, it is necessary to have enough skill to disassemble the Engine.
If you are not a professional, it is better to ask a specialized Motorcycle store for help.
It's good.
View detail
Fits: HONDA NS250R, HONDA NS250F, HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Used at TA20ACarburetor in MC18.
Used at TA20ACarburetor in MC18.
Carburetor's Overhaul was successfully completed.
This Quantity:If I had found Set first, I might not have wasted my money.
View detail
Special labor is required for replacement
In order to pull out the Needle bearing assembled in the Case by the OEM, the
A Bearing Puller is required.
The compatible shaft diameter is 14mm.
InnerPuller for ball bearing may not work.
We forced it out with a 15mm puller for ball bearings.
If you can afford it, Puller should be prepared.
On the other hand, the assembly of Tougashi-kun itself does not require a special tool.
Socket and Hammer are sufficient.
The product itself is very solid, so
After assembly, you will be thrilled by the lack of rattling.
It is a good product, although it is difficult to replace.
View detail
Carburettor screws
Excellent product, compliant with the original, I recommend its purchase, if you overhaul your carburettors you cannot miss them View detail
![[Pepex Seal] Low Friction Oil Seal](https://img.webike-cdn.net/catalogue/images/107950/F10-21002_01_TS.jpg)
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Cannot be installed on NSR250R and SP Mag TEC.
NSR250R is listed as an appropriate vehicle model, but it is different from SP Mag TEC in terms of xyz and cannot be installed.
SealSize is listed, but unless you are smart enough to look up Aluminum Wheel and Mags Wheel in the Parts List, you will make a mistake.
View detail
Nice bit of kit!
Awesome bit of kit! Now I don't need to do a wire splice as this harness does the job for me! Very simple plug and play. It is easily reversible if needed... Good price too! Not going to a dyno but bike feels sharper if you know what I mean... View detail