Reviews
MFDRim stripe for 14Inch 4M Candy blue
Used for Wheel of Car
We selected the 14inch wheel because it was a 14inch wheel, but if you want to use it for a wheel in a car, please use the 14inch wheel.
It seems to be correct to use 1Inch lower Size (In this case, it is better to select for 13Inch)
It is not impossible to put it on, but you need to be careful because there will not be much room at the joints.
View detail
Beautiful and hard to peel off! Easy to immeChain!
Convenient for when you want to immeChain a bit! Very beautiful!
It is well made, hard to peel off and easy to apply!
It's nice that there is a spare in the package for misapplication!
Hold on to the Rim tape until you change the Wheel. (Lol)
View detail
Degreasing is important.
Wheel stands out in Titanium color.
Degreasing is quite important. If you do not do it many times, it will peel off.
It was more cleanly applied without detergent solution.
If you have the OP's Squeegee, you can put it on without shifting.
View detail
Rim stripe looks surprisingly different
I bought it to dress-up the wheel area. I think it also has a slight function of guarding the area around the rim, which is prone to scratches.
When pasting, apply with water. I used Guide, but the rim stripe may be slightly shifted where it overlaps. However, it is not noticeable unless you look at it with a gun.
Since it will feel like air bubbles are rolled in, Image is a Large cut that pushes out air bubbles when applying.
Although it is a non-reflective type, the change in appearance is large, and I thought it was a part that makes it easy to feel the changes in my car.
View detail
Rim stripe easily affixed
Used for Rim stripe installation on YZF-R6 (2019).
When used for water pasting, Rim stripe can be applied quite accurately and effortlessly.
Some adjustment may be necessary where the rim stripe overlaps.
It is also Large cut to paste with Image to push out air bubbles. Removing air bubbles afterwards is also Large cut.
View detail
I tried to match the color of the car body.
I switched to Triumph Tigers Ports 660, so I put the same MDF rim stripe as before.
The color is Blue to match the color of the car body.
I ordered and received it in about 3 days.
As shown in the instructional video, degrease the wheel attachment area and mist the wheel and tape with water containing 1 or 2 drops of neutral detergent. Then, using the special Gauge, I attached the 4 tapes. After the tape was attached, the heat gun was used to warm up the tape and fix it in place.
If the initial positioning and the next Tape overlap are done properly, it is not a difficult task.
Durability and fading are unknown due to the short period of wear, but price-wise, Solid Collar should be a little cheaper.
View detail
It stands out on Gentle because it reflects beautifully depending on the angle of view.
I applied 16~for 17in. of MirrorTYPE Blue to a 10inch Scooter. I am satisfied with the feeling that the Wheel itself became more luxurious than the original color! View detail
one's fashion style begins with one's feet
Recently, I feel that many cars have rim tapes, but Small's partner is all in blue, which is simple and fine, but I wanted something different, so I decided to customize the rim tape.
In construction, the challenge was to use a guide jig.
After thorough cleaning and degreasing, we carefully applied the adhesive.
Anyway, I felt that the best way to hang is to take it slow at Timing, where there is plenty of time.
I put it up and wow. It's pretty good, isn't it?
It is a world of self-indulgence, but it is a good custom with a Sporty atmosphere.
To make it adhere firmly, it seems to be a good idea to finish it off with a heat gun or the like.
Items is perfect for those who want to improve the appearance of their products easily.
View detail
Basically, they are MUST dress-up parts.
[How is it used?
The new car is a must-have dress-up part when purchasing a new car, because it can be dress-up at a low cost.
The footwear looks tighter and can be reupholstered in another color if you get tired of it.
There is no effect on the run itself.
Was the one you received as per Image?
YES
How was your experience with it?
Satisfied
[Points to note]
Since there is a special jig for attaching the product, it is possible to stretch the product beautifully by using the jig.
How did it compare to other products?
No problems with thickness and adhesiveness
View detail
Dedicated Attachment Gauge required
I was a little worried because I didn't know the texture of Mirror red, but it turned out to be good. I applied it with water. There is a little hang at the beginning and at the joints, but it can be easily done if you have a special adhesive gauge. I did it in a small place without lifting up, so it was strange that the surface was too large to show the paste.
Once you press it down, you should not reapply it.
View detail
It's so cool!
14&13Inch
Note the order in which they are put up!
From top to bottom:Front4cards??Rear4cards??RearQuantity:1 Set of 4pcs.??FrontQuantity:1 Set of 4pcs.
Note that it will Gap if it is applied appropriately.
If you look closely, you can see the different lengths.
I thought on my own that the colors would change to rainbow colors,
Originally, each is colored.
Parenthesis is good, so I'm satisfied!
View detail
Very grateful for bulk sales.
I bought a full set of Attacker model some years ago and
When I put it on my XG250 TRICKER, the impression was completely changed and tightened up.
I liked it very much.
A plastic part of the Tail cracked while driving on a forest road.
License Plate can no longer be installed.
I had to replace it with an Assy, so I bought it again.
It would be nice to be able to sell only the parts we need in bulk.
XG250 TRICKER has been discontinued for several years now, so I don't know how long they will carry it.
The Sticker on the Fork and Swing Arm is also in question, so I will try to repair it when the time comes.
The initial investment is high, but it is partially replaceable.
It is cosmetic in the sense that it can be used for a long time.
View detail
Wheel is Parenthesis good
It is not difficult to apply and the colors are good, so it is easy and cool. View detail
The thinning liquid is a Large thing if the procedure is followed.
I tried my first ZDress-up.
After much research and hesitation, we decided on Mirror violet, with the theme of casually shining and glowing.
The first step is to install the wheel, using MDF Scale, which I have used before, and first degrease the wheel thoroughly with Silicon-off.
After the entire wheel is removed, the adhesive is simply applied using Scale while spraying a detergent thinning solution.
I followed the procedure to paste one of the 4 stripes, but it suddenly peeled off, failed, and fell to the ground, unusable! I try to paste one more piece, but it feels slippery?
The cause was that when making the diluent, the amount of neutral detergent was wrong and there was too much detergent, so the adhesive was not strong enough and it fell like a stream...
After adjusting the thinning liquid again, the adhesive strength improved and work proceeded smoothly, but there was no room for error, so we proceeded with caution and care.
After that, I managed to complete the job on all four wheels in one shot, and upon confirmation, a drop or two of detergent in the thinning solution should be enough!
Small diameter wheels have a large bend, so even if you use a dedicated scale, you need to be careful.
The impression of the finished product is quite good, with a very austere appearance.
When the sun is low in the morning and evening and light reaches from the side, Mirror's flamboyance is emphasized. On the other hand, when it is cloudy or at night, it gives the impression of a dull reflection and glow.
The Violet is a darker color, so it is not so noticeable in the absence of light.
I have been using MDF's Stripe for a while now and the durability is excellent, the thickness and quality are definitely better than cheaper ones, but a word to MDF, can you please make the Small Diameter WheelSpec. in a little more quantity instead of just two spare sheets?
Large and Small diameter Wheels with bends require a lot of construction work and hang.
Even with the use of a dedicated Scale, the work was not as nerve-wracking as it could have been.
View detail
I chose it to match the color of the car body.
We decided to put a rim sticker on the Ducati SCRAMBLER to match the color of the car body.
Since MDF had been used for the past three wheels, we chose to purchase MDF this time as well, even though it is a little expensive rim sticker.
I wanted to put up a yellow-colored delicolore, but there was no Variation and only one color, yellow, was available.
There were 18 Rim stickers attached to the two Seats, and at first I could not tell which Size was the front or rear.
The paste was done as described, but it is not perfect.
If you look closely, you can see some distortion, but it does not feel out of place with the Body color, and I hope it stands out anyway to prevent accidents.
View detail
It's solid
Up to now, I had applied MDF Lime green and 10mm rim stripe on the wheel painted black, but now I have replaced the rear wheel with a ZRX1200R one, so I purchased the same MDF rim stripe and reapplied it on the front.
I thought that if I was going to replace it, I would use Makeover, so this time I decided to use a thinner one, 6mm and 4mm, and I thought the thickness should be 6mm and the color should be different, but in the end, I chose 6mm Lime green as the same color because the other colors did not feel right to me at all. I chose the same color, Lime green, 6mm.
First of all, after removing the Tape that had been attached, I felt that the Rim stripe on the MDF is a no-mistake thing. The MDF rim stripe is very firmly attached to the tape. It is not difficult to peel off, in fact, it was easy to peel off without breaking off in the middle, but unless you try to peel it off intentionally or accidentally, it does not seem to come off naturally. For a cheap rim stripe review, see It's peeling off." etc., but this does not seem to be the case with this Rim stripe.
As for the application process, I believe it can be done with the wheel attached to the car body, but I did the work with the Timing with the Wheel removed. I did the work with the Timing wheel removed. I cut out the backing paper for each tape, degreased the rim of the Wheel, sprayed water lightly on the rim with a mist, and started pasting. When pasting, hold the tape so that the Start position does not move, and trace the tape with the belly of the finger of the opposite hand so that the water drains from the adhesive surface. Finally, warm the Tape with a dryer to make it adhere to the Rim. If you pull too much when applying the tape, the finished circle will be rattled and the adhesion of the sticking part may be weakened, so be sure to adjust your strength. However, the thinner the tape becomes, the more easily it is affected when it is pulled. Also, the overlapping area should be even etc., and since there will be a gap between the tape and the rim above the overlapping area, it is important to warm the tape firmly so that it adheres to the rim. The finished product was generally as I had imagined, and I think it would have been white even if I had made it 4mm.
View detail
In Black wheel's Accent.
The black painted wheels looked too heavy, so we introduced rim stripe.
I was confused with Titaniumium color for a long time, but the one that goes better with my ZEPHYR color is
I figured it would be the Blue one from Delicorol, so here it is. 。
This may be due to the fact that I did not use RimGauge when pasting.
If the overlapping dimension of the connection part is about 10mm, the last overlapping part overlaps by about 30mm.
I reposted it. 。 Maybe without RimGauge it would unintentionally pull and stretch when pasting?
The color overlap part here is the "Colored" part, so the above problem will not be so much of a problem if you make the spec. overlap in the "Black" part....
View detail
One point on your feet.
Purchased Black6mm.
I bought it as a One point kind of thing, but I think it could have been a little thicker.
The workability was good, and since we purchased the special Gauge, installation was easy.
It would be troublesome without a dedicated Gauge. (Quantity):(Set should be sold)
I am satisfied with the product.
View detail
It purchased for appearance. A result is large satisfaction. Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not un
It purchased for appearance.
A result is large satisfaction.
Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not unexpectedly conspicuous.
(Natural although there are differences of enough if compared with normal ..) Although it thinks that the angle which takes a photograph is also a problem, the impression which is seen rapidly and received is the touch which says that the edge of the tire spread inside.
If appearance was thought more as important, possibly the monochromatic blue product should have been chosen.
Anyway, since it is satisfied with the product itself, I purchase and think that it was good.
However, since this stripe has become comparatively for 4 minutes, the point worried one sticks it, as the portion of a joint overlaps for a while.
(It seems that it is the measure which considered the hit in case of the size of exactly since it is hard to stick by it) If it sticks in the pile and the crevice between joint parts is not processed exactly, garbage will enter from the crevice and it will become a cause of peeling.
Those who are worried will think whether it is satisfactory, if the portion of a joint is cut.
Since I was troublesome, I stuck in piles as it is as the description.
If this point and an edge are separating, I think that it will cut then.
View detail
It corrects, although it described that the wrinkle was in play contained last time. When 24 hours or more passed, the wrinkle had disappeared. It is in play at the time of 12-hour progress last time.
It corrects, although it described that the wrinkle was in play contained last time.
When 24 hours or more passed, the wrinkle had disappeared.
It is in play at the time of 12-hour progress last time.
View detail