Reviews
ปะกับคันเร่ง daytona มาครบชุดพร้อมใช้งานโอเคดีครับ เลื่อนไหล ก็สมราคาอยู่ครับ ไม่แพงใครมองหาปะกับแท้ราคาไม่แพง View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Used for NSR50OEMcarburetor
Purchased a new High Solo with long wire when converting to bar handle.
Is the standard CR80OEM rumored to be discontinued in Mania?
Selected because I thought DAYTONA was a safe choice.
Outer wire length 870mm
Bar handle conversion is a little bit long.
I think it is a little long for OEMSeparate handle, you should choose 760mm.
In the case of NSR50, even if it is a little long, it will not cause any problem.
(In the case of Race Specification, handling problems, etc.)
Guide falls off when guide is temporarily lowered for assembly.
I looked at the Instruction Manual to check the installation orientation, but there was no picture in the Guide.
It seems a little unkind.
Solution by turning this way and that.
This time mounted on OEMcarburetor
The Outer length adjustment in two places was extended almost to the maximum Large, and the play was managed to be appropriate.
Wouldn't it be better to have a shorter inner wire? (about 10mm)
It's a Universal Product, so that might not be a problem.
Included Wire part number:29223
for RepairWire Part No. 29239
I even thought there was a packaging error here.
The degree of opening is meh High Solo lol.
May be appropriate if converted to PWKetc.
Not checked that one, I have a PWK and would like to check it eventually.
The car is still in the process of being built, so a running check has not yet been done.
With fewer and fewer options available, I'm just thankful that it's on the lineup!
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Very good
It may be tough in Circuit if you don't play less View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
being on the right track
I used an XLR80 Frame with an APE 100 Engine and a carburetor with a TM-MJN24.
The XLR80 itself is NORMAL and High Solo, so I don't feel much Merit as High Solo, but I am satisfied because I can now pull off MJN24. The included Grip is a replica of the TZ Grip, which I personally prefer.
If you are replacing the throttle holder of the APE etc., you can easily feel the effect of the big cab pull-off.
This time I got it because I needed to buy a Throttle holder, but if you are planning to use it in an Off car Big cab, I think replacing the Wire is enough to give you a High Solo feeling.
It's not overly sensitive as a high solo or a big cab throttle, and I think it's just right.
If I wanted, it would be better if it were a little cheaper.
View detail
A decent throttle for Fi
I bought this High Throttle for my Honda RS150 that fits perfectly. The quality of the item and the finish is great. I have to modify the item as i instaled it in a throttle body rather than the carb recommended but it still fit fine. This is cheap throttle an alternative throttle for a premium throttle. The item is package nicely. It was ship wraped in bubblewrap so item is protected. Make sure that the length of the cable is compatible witj the motorbike your going to use. View detail
High Solo with the best cost performance
Not suitable for street youth.
For Circuit.
Reason:Because it is difficult to adjust Speed with Throttle alone.
View detail
Trusted DAYTONA
I thought that it was good for the repair measure of the accelerator wire off of my friend's SUPER CUB C50 modified 124ccPipe HandlebarSpec. and introduced it.
The carburetor and accelerator wire of a certain Horizontal TypeEngine 124cc Full kit became bad, and the carburetor was changed to YD28.
The taking out position was changed, and it became better temporarily, and it was relieved.
However, when I heard that Axel didn't return after switching back, and I visited to check, I found that there was a dislocation of the Accelerator Wire attachment part of the Switch box original.
I have repaired and adjusted the handlebar many times, but the angle of the handlebar cut, the length of the wire, and the position of the fitment were not good, so I gave up and considered a new installation.
I picked up a few kits that are hard to remove, easy to adjust, have long guide wire, high solo, and repair parts available, and have standard long wire that corresponds to the length of CUB frame.
At any rate, I'll replace the Grip at his request, and until he has more time. "Take the Small stuff home and work out the tentative matches and Ideas. So, I worked on it.
This is a perfect feeling. I'm looking forward to installing everything into the car and driving it in the real world.
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Cheap, good looking, NORMAL chick
I was using AluminumHigh Solo from another company However, I wanted to change to DAYTONA's High Solo to make the handling NORMAL chic I did
For those who want to look like they're tuned in, the AluminumHigh Solo I think it's better But this one is better for those who want to handle the handlebar area in a NORMAL way I think it's good
It made me feel better
View detail
I am satisfied.
It was the same product until now but Wire was somewhat elongated so I purchased it as a spare.
Since 2 St Parts are decreasing, I think that I want to use it for Large.
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
You can use it with XR100R!
I use it to control YOSHIMURAMJN - TM 24 with XR 100R. When used for PD22 of XR100 REMEM, since OEM's Throttle Wire can not be removed from Top cap of PD 22, Takegawa's Top cap (Out of print?) Can be used without problems if replaced with (NSF 100 should be using Throttle and carburetor of almost the same form).
You could use it for YOSHIMURAcarburetor. Wire handling should be taken Large. There is no problem in the adjustment range of Wire's play.
High Solo feeling is the same as XR100ROEM or feeling that it became High Solo.
The attached DAYTONA 's Grip is neither nor impossible.
View detail
Hi all, This throttle, grips and cable are great quality, great fit and finish, East to install. I would highly recommend this product to anyone looking for a good quality throttle.
Hi all, This throttle, grips and cable are great quality, great fit and finish, East to install. I would highly recommend this product to anyone looking for a good quality throttle. View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Used with GORILLA
I bought it as a new High Solo because I put OKO 21 pie on GORILLA.
To GORILLA, Cable was a little long and it was difficult to walk around, but I am satisfied with Large at an affordable price.
View detail
Performance as expected !!
I used it for YOSHIMURATM 24 MJN. The length of the Accelerator Wire that was attached with Frame 3 cm long, Semi-up handle was sufficient.
The shape and the making of details are satisfied with the beautiful finish.
Also, Black's Body has White letter in DAYTONA 's Logo stand out, I thought that I like Parenthesis but I purchased it "White Logo" There was not, it was a thing digging the logo of DAYTONA.
Please change Catalog as soon as you change.
View detail
Make it solid and beautiful finish!
I am using it for YOSHIMURATM 24 MJN.
The length of the Accelerator Wire that was attached with Frame 3 cm long, Semi-up handle was sufficient.
I made it with DAYTONA firmly and purchased securely with a beautiful finish safely.
Actually attaching and pulling it is light!
Also, in White's character on Black's body "DAYTONA" Although Logo was included, the product that I received was a thing that was changed, not a White character but a stamped logo of DAYTONA.
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Race Necessary for vehicleization
During Cornering, because the body is tilted, Normal throttle will hurt the wrist, if this DAYTONAHigh throttle it is about half as compared with about NORMAL. View detail
Wire is ...
The opening angle of Axel is as expected and it can be fully opened without having to grasp Grip.
Since I use it with OEM's Carburetor, I relaxed it just before I got out of Adjuster of Body and Wire, and finally got a proper play.
View detail
Exchange from a different High Solo
Previously I was using High Solo for Minimoto, but I chose this product because I want you to be a little more High Solo. It certainly became High Solo, but I think that I wanted it a bit more.
By the way, carburetor is used for OKO 28 φ.
Some people think that this is enough.
It is enough for construction and accuracy in detail and it is manufactured much more properly than for Minimoto.
Because it is inexpensive in terms of price, this has a sense of affinity. I wish I had it done from scratch - - -
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Mounting on NSR50
Mounting on PWK 28 of NSR 50.
Easy to install and Length of Cable is also the best. The movement of Throttle is also good with Smooth. You can open Axel comfortably!
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
It is used with KEIHIN PWK28 pie.At 55 degrees, it is not opened fully as explanation of Manufacturer Site... Although it is a Level which can be used for non-difficulty, a Wire is a little long a little.
It is used with KEIHIN PWK28 pie.At 55 degrees, it is not opened fully as explanation of
Manufacturer Site... Although it is a Level which can be used for
non-difficulty, a Wire is a little long a little.
View detail
Fits: HONDA NSR50, HONDA NS-1, HONDA NSR80
Old type Honda It attached to the DAX.Since the price was cheap, it seldom expected, but it is attached simply and a function is also satisfactory at all.
Old type Honda It attached to the DAX.Since the price was cheap, it seldom expected, but it is attached simply and a function is also satisfactory at all. View detail