Reviews
If used gently, it will last somewhat longer.
[How is it used?
It is used during Tire replacement &Puncture repair work on Dual Par Pass cars.
Many Dual PurPass vehicles that enjoy mountain play and forest roads use a Tube in the Tire, so these Items are very useful for getting the Valve of the Tube out of the Valve hole in the Rim.
Wire is thin, so be careful when working with it, as the handle clasp can easily come off or the wire can easily break if pulled with force.
Did you receive the item as per the Image?
I used to use a similar product from another manufacturer, but it was used roughly and broke, so I bought this product, which was a little cheaper at Webike at the time.
The product was as per the Image.
How did you like it?
Once you get the hang of it, you can easily pull out the Air Valve in no time at all.
Especially in winter, when tires become hard, I can't do without this product.
[Points to note]
As I wrote above and others have written. "Forced to pull by brute force." The product is fragile when you try to pull it out.
Although Manufacturer is different, if you search for DRCAir Valve Puller in the product introduction section of Webike, you will find a video at the bottom left of the introduction section that explains it in an easy-to-understand manner. If you are not sure how to use it, please refer to the video on YouTube.
How did it compare to other products?
I used to use DRC's Air Valve Puller before this product, and my personal impression is that it was easier to use DRC's Air Valve Puller because the Wire tends to rotate when Screw-tightening the Valve. (Possible individual differences) 。
Other items that would be helpful
Point and hang of installation
With your free hand, press lightly on the backside of the valve of the tube toward the rim while guiding the tube.
The rest, as I mentioned above, you can watch the video.
Basics We're not in a hurry. We're going to do our job well and reliably." is the best shortcut.
[ITEMS TO BUY TOGETHER
Prepare Lever, BEETWax, Inflatoretc. for Tire removal and attachment separately from the things to be replaced.
[Opinions and requests to Manufacturer
It would be nice if you could use a stronger wire to ensure durability, but we would be grateful if you could just keep this product in the lineup.
View detail
portable
It is not something I use often, but I carry it in my first aid bag for touring.:I think it is cheap at 1 Set of 2pcs. View detail
Easy to use
It is very convenient for maintenance of motorcycles because a small amount of grease comes out only as much as you press it, so you can apply it without getting your hands too dirty. View detail
One for the toolbox
I used to use a valve cap that I thought was made by for Motorcycle. I used to use one that seemed to be from for Motorcycle, but I lost it because it was small like the Valve cap, so I bought the Valve Core Spinning from DAYTONA. I lost it and bought Valve Core Spinning by DAYTONA this time. It is also very easy to turn because it is just the right size. View detail
Must needed tool when removing the TW Flywheel
bought this OEM bolt when I needed to do work on my tdub engine.TDUB ,The flywheel is mounted onto the tapered end of the crankshaft. It is secured from rotating with a Woodruff key, and is tightened down by a bolt that threads into the end of the crankshaft. To remove the flywheel, you must first remove this bolt, The next step is to thread a bolt ( THAT'S WHAT THIS OEM BOLT ABOUT ,CALLED OEM ROTOR PULLER OR FLYWHEEL PULLER) into the internal threads of the flywheel.The TW's rear axle is the correct thread and can be use to do this also BUT I don't want to take any risk and buy a YAMAHA OEM BOLT ,THAT DESIGN TO DO THE JOB WITHOUT HESITATION.As this bolt is tightened, the flywheel will be pulled free from the tapered crankshaft. All threads are standard right hand threads . Then secure the flywheel from turning and then try to remove the Flywheel bolt first Then you should be able to use a proper sized bolt/flywheel puller to get the the flywheel to pop free. The proper thread size needed is 16mm x 1.5 RH . as usual package received very quickly after dispatch from japan. quality packaging and quality service .thank you WEBIKE. Highly Recommend Online shop. 5Star View detail
Used to secure Plate to repainted Frame
I bought a battered 900SS (900SL) and am Restore.
For the frames with noticeable rust, I had originally planned to remove the rust by rubbing the paint off with a wire brush, and then finish with a two-component urethane can spray from DAYTONA, Soft99, or Okitsumo.
However, when I rubbed the slightly rusted area...I found that the rust was progressing like a worm crawling under the paint film.
We had no choice but to strip off all the paint, but then the problem would be the MODELPlate that is Rivet-fastened to the frame.
It is clear that the display printed on the Plate would also peel off if the Plate is left as it is, so the Plate was removed before the paint was peeled off.
After stripping the paint, removing the rust with sandblast, and powder coating (we gave up on the two-component urethane can spray finish because the rust in the intricate areas was too severe to remove with a wire brush), the Plate must now be mounted on the Frame. I gave up on the two-component Urethane can Spray finish.
This Rivet was used in that case.
There is no particular element that says, "This is the only Rivet! It is a very ordinary Rivet.
Aluminum Flange、Stainless shaft。
I could have purchased it separately at Home center, but it would have been a hassle to go and buy it, and I bought Rivet along with my other purchases.
There is no absolute necessity to buy at Webig, but it is convenient to be able to buy small items such as these all at once.
These ultra-fine Size Rivets are I went to the home center and it wasn't there. What a frequent occurrence....
It may be a little cheaper if you buy from a specialty store like Monota0u, but if you consider the shipping cost and the hassle of having it delivered by RoseRose, it is more economical to buy from WeBig for a small price difference.
And there's no way I'd buy just this one.
The feeling of using the Rivet is very normal, so there is nothing special to say.
If I may say so, it is better to prepare a bag with a zipper if you do not plan to use it up, because it is not designed to be stored when the Package is opened (it is just a Blister pack).
View detail
Very convenient... ♪
Good cosmetic.
If you have all of these, you will not have any problems with Large bodies.
View detail
This is handy.
I have a regular and a short latchette, and I have never used a swing type. I have never used the swing type, but there was a swivel type, but I didn't like the instability of the swivel type.
When you use it, it is easier to use than expected. When you turn it, it makes a light ticking sound. The swing type has the movable axis in front of it, but the swing type is right beside it, so it does not feel unstable. Moreover, since the Swing type is clamped from both sides, you can loosen the nut and then turn it vertically in a round and round motion, just like a driver. You can also use it as a simple Small Type Wrench by turning the handle to the side.
The direction of rotation is changed by Dial type, not Lever type. The round push button is the center of the dial, which covers the entire surface. This way, there is no mistake in pushing the button.
Orange Material for the handle:Plastic. Normal Material:Plastic tools are lightweight but often crack over time or slip during use. I do not know how they change over time, but I did not feel any slippage when I actually touched them. I think that not only the shape but also the texturing process is good. When the handle is straightened from the "Ding" position, the resin handle is held in place by the core rod of the Gold genus. This is a good use of the characteristics of resin.
The stiffness of the Ratchet upper and lower movements can be adjusted with the Hexagon Bolt 3mm on the Gold axis. The central bolt on the handle is a star-shaped T10. The bolt on the handle is not something you want to touch.
It was easy to use and the Small Type was ideal as a take-out tool. I felt it would also work well as a regular tool in the workshop.
View detail
This is enough for the Torx bit socket of T30
[How is it used?
Used to remove the key cylinder from the Top Bridge of a YAMAHA TZr50R.
I had TorqueT40 for XJR400R Rear suspension, but the size was different, so I had to purchase additional TorqueT40 as Single Item.
Was the one you received as per Image?
It was just as Image.
I checked the size in Home center before purchasing.
How was your experience with it?
It works fine. SK11 is very good for DIY riders because of its cost performance.
[Points to note]
Not particularly
How did it compare to other products?
Torque is rarely used on domestic cars, so I think that SK11's most cost-effective tools will be enough without buying expensive ones.
View detail
I should have bought sooner
Until now, the company's L-Type Quantity:It was opened and closed by twisting and turning it with Set's.
I had been thinking of getting a Type T for some time, but had held off because I thought the work time would be much the same.
However, as I got older, I changed my mind and decided that I wanted to have as much fun as possible, so I took the plunge and bought a frequently-used Size one.
When I used it, the work efficiency was different!
I regret that I have wasted my time so far.
View detail
Made by DAYTONA because there was no Size for KTC's one.
Until now, KTC's L-Type Quantity:It was opened and closed by twisting and turning it with Set's.
I had been thinking of getting a Type T for some time, but had held off because I thought the work time would be much the same.
However, as I got older, I changed my mind and decided that I wanted to have as much fun as possible, so I took the plunge and bought a frequently-used Size one.
We mainly use KTC tools and wanted to get the same Manufacturer, but there were no sizes available, so we bought DAYTONA tools.
It is as easy to use as KTC, if not easier, and the T-type could have been made by DAYTONA.
View detail
Hammer for punching
[How is it used?
I was looking for a large hammer because I had only a small hammer to smash during maintenance, and a large hammer is also a small hammer.
Anyway, I bought it because it was big and looked sturdy.
Was the one you received as per Image?
It has a reasonably Limit weight to support with one hand.
It was quite ideal.
How was your experience with it?
It is useful in many ways, such as tapping the Shaft and Shock driver.
I have been handling it roughly, but so far there has been no damage.
The grip of the handle is also good so it does not fly away.
[Points to note]
It has a reasonable Size feel to it, so it is difficult to store.
Also, since considerable force is applied to the parts, there is a possibility that the parts may be destroyed if the work is done in a frustrated manner.
How did it compare to other products?
The power is different than the chubby Hammer I had on hand.
【Review】
This tool is unnecessary if you just want to maintain your Motorcycle normally.
It can be used to pull out rusted or stuck shafts on immobile or abandoned vehicles.
View detail
Required when replacing Tire
It is essential when replacing Tire.
Since it is a Small Tire, it can be used with a Small Tire.
View detail
Trusted KTC
[How is it used?
Purchased a new Driver because I lost the one I had been using.
I bought this product because I thought, "If I'm going to buy something, I'm going to buy KTC!
Was the one you received as per Image?
It was as per Image as it was a product I had originally seen.
How was your experience with it?
It is easy to grip and use, and I felt that it is a Driver that I will be able to use for a long time to come. The construction is solid, so I think it is a large difference from cheap drivers.
[Points to note]
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
scratch-resistant
It is used for removing and attaching parts that you do not want to damage.
Size, it seems to be good in terms of weight and can be tapped without scratching.
It is useful to have different sizes so that you can use them in different ways.
View detail
scratch-resistant
I purchased a plastic hammer to avoid scratches and damage when removing hard assembly parts.
The weight, Large size, and ease of use seem to be good.
View detail
Fits: HONDA CB50, HONDA MONKEY, HONDA DREAM50, HONDA DREAM50, HONDA DREAM50, HONDA SUPER CUB 50, HONDA GORILLA, HONDA APE 50, HONDA APE 100
It is used infrequently.
It is still easier to use dedicated tools. View detail
Case may not be necessary.
This is a product of Z-EAL, a brand of ko-ken that is trying to develop a small type that is not limited to the general industrial standard, so it is the best choice for users who prefer 1/4 size. Is it the best choice for users who prefer 1/4 size? It is so small that you may laugh a little.
The Ratchet, which is slender but has a click feeling unique to ko-ken, has been spec. changed to 72 GEAR in the 2023 Spec. change. Quantity:The Ratchet included in the Set does not have a push release, which is fine with me since I am not too concerned about it, but it seems to naturally lead to the suppression of overtorque, partly because the Ratchet is a Small Type, which also makes me aware that it is a high-end product.
This Quantity:The set includes a 4.5mm hex socket and Plus minus bits, which are not used as often as you might think, so if you prefer to be a little more selective about what you put in and want to pay less, you can order a special quantity from FACTORYGEAR.:There is a little more content vetted at Set, so that might be a good choice.
Material:It comes in a plastic case with a luxurious feel, but the Socket does not sit well against the Sponge, which serves as a Holder, so it becomes RoseRose inside when carried around in the case, which is very annoying.
In my case, I bought individual TONE Aluminum socket rails and put them in my tool box.
Originally, I purchased this product because I wanted to make a high-precision socket to be used with the 1/4 size Torque wrench for low Torque of Tonichi, but if I want to do maintenance such as removing and installing the exterior and around the carburetor, this quantity is perfect.:Set alone seems to provide almost everything. You may not need to use 3/8Size except for the undercarriage.
View detail
Good thing it came in a two-pack.
In the summer, when we replaced the radiator hose, two of the OEM hose bands reached their limits, so we had to use a hose band purchased at Home center as a stopgap measure. In the meantime, the Material:The Stainless Steel one served its function, but the band was 13mm wide and I didn't like the look of it.
When we went touring the other day, there was a small amount of coolant leakage from the hose that connects to the Radiator, which splashed around and stained a part of the Engine white. Needless to say, I washed the affected area as soon as I got back because coolant has a bad effect on the paint.
There were no coolant leaks for a while after the hose was replaced, so we assumed that the band had loosened. It might have been OK to retighten the band as it was, but we decided to replace the band because it might loosen again and we did not like the appearance of the band.
Among the many hose bands available, we selected the DAYTONA band, which is narrow at 8mm in width and can hold two hoses, but is also Reasonable. However, the Radiator hose at the location where I wanted to tighten is about 32mm in diameter, and this product can be used from 25mm to 50mm, but there would be a surplus of large size. Unfortunately, DAYTONA does not sell a product in the correct size.
I decided to replace the Band and broke the first one. I tightened the screws too hard to make sure they were tight enough, since they had leaked coolant, but the screws spun around and damaged the Band, rendering it unusable. The second one was tightened carefully and firmly, and the coolant leak was solved.
The second one was going to be used to replace the band on the Hose under the tank the next time I remove the tank, which is a shame. I regret that I was not careful when tightening it in.
View detail
I don't want to put a scratch in it.
It is used to remove parts that are hard to install or adhered to in places where you do not want to scratch.
Size:#1, 1 PondLength, HeadLargeThickness and weight seem to be the most convenient.
The cost is easy, and the head can be exchanged, so if you have 1pc. you can use it in various ways.
View detail