Reviews
easy to read
I installed the mirror on my MONKEY125 because it was hard to see. The rearward view is not only easier but also extended to the front, so I can use it very comfortably with less eye movement. View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
TANAX OFFSET HOLDER 45
Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the side mirror visibility. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. -------------------------------------------------- -------- Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the view of the side mirror. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. Powered by Google Translator View detail
Best product!
I ride a current Z400.
Before installing this product, I could not even tell if there was a vehicle behind me, but after installation, I can see it differently and I am satisfied with Large.
If the price were a little lower, it would be a perfect score.
View detail
relief from a worry
I bought this for my CT125 because the LeftMirror is in a strange place and it was hard to see the back of the car.
I am happy with this Parts and it is much easier to see.
I was torn between 30mm and 45mm, but the 45mm is just right.
View detail
TANAX OFFSET HOLDER 45
125 years old, 125 years old, 125 years old.
I want to know more about this.
I bought the genuine Monkey 125 side mirror because I couldn't see the rear clearly.
After installing the offset holder, the mirror viewing angle will be good, allowing you to see what's behind you and drive safely. -------------------------------------------------- -------- The side mirror of the genuine Monkey 125 was purchased because it could not show the rear. After installing the offset holder, the mirror viewing angle is good, so you can show the rear so you can drive safely Powered by Google Translator
View detail
Back MirrorImproved rearward visibility
The rearward visibility of the Grom OEM Mirror was poor (about 1/3 of the arm was reflected) and I had to retract my arm every time I checked the rearward view.
When we tried to install it as it was, it interfered with the Throttle Wire, so we had to loosen the nut that secures the Wire and adjust the angle.
The installation has improved the reflection of the arms considerably, though not completely.
View detail
Fairly easy to see.
[How is it used?
Used to improve visibility of VTR250OEMMirror.
Was the one you received as per Image?
As per Image
Was the installation difficult?
The angle adjustment was troublesome, but not difficult.
How was your experience with it?
Moving the Mirror forward has improved visibility considerably!
[Was there anything that disappointed you?
None in particular
[Opinions and requests to Manufacturer
It looks wild.
I would like to see a Mirror that can be placed further forward than the OEM without this.
View detail
More effective than imagined
We chose side-view mirrors because of their design, but the angle was poor due to the combination of other parts, and we could hardly see the rear of the car...
I installed these Parts on a good day and was surprised to see that the visibility was better than with the OEM Mirror. The Bolt does not loosen while driving and the Mirror does not vibrate.
Worth a try if you have trouble with Mirror's visibility.
View detail
Expected
It is only 45mm, but it is very effective.
Quantity:Pair (for Left and Right) Both are in use, but with almost no blind spots in the rear.
That was a good purchase
View detail
Tanax Napoleon OffsetHolder
[How is it used?
Used to attach Knuckle Visor.
Was the one you received as per Image?
It was more solid than the Image had been.
Was the installation difficult?
It's not hard.
Need 8mm Hexagonal Wrench.
I went to buy it because it was only available in 6mm at the Largest 6mm.
How was your experience with it?
It needs to be tightened down very tightly.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
8mm Hexagonal Wrench needed and prominently
Would have been nice to have a warning.
View detail
Used to install Knuckle guard and Mirror at the same time
[How is it used?
To install the Knuckle guard and Mirror together in a rational way, we used OffsetHolder.
Was the one you received as per Image?
Aluminum Casting and appears to be Black color Painting, not Anodized.
Was the installation difficult?
Technically it's not that difficult, but how many times do you need to change the Handlebar to a Quantity:Pair (for Left and Right) The position was determined by repeatedly making fine adjustments while checking for contact with the Upper Cowl and Screen. In addition to the Offset Holder, an Opposite Thread Screw Adapter (product number:HM-10) from TANAX was used to raise the Offset Holder by 20mm to avoid contact with the Accelerator Wire. For the guard installation, the Knuckle guard bracket was installed from the underside of the OffsetHolder, taking advantage of the long screws in the Mirror Bracket.
How was your experience with it?
We were able to install multiple components together with the Refreshing without any clutter.
[Included Parts:were they on?
M10 Bolt1 pc included.
[Was there anything that disappointed you?
I think it is a little expensive. less than 1000 yen is ideal.
Other items that would be helpful
Mounting points and hang/ All ScrewBolts were coated and tightened with low-strength Screw lock fluid to prevent loosening.
View detail
When I replaced the Mirror, it became difficult to see.
ZrX1200DAEG with Cross 2Mirror
I could only see my arms, so I installed them.
The angle needs to be adjusted, but it's much easier to see.
View detail
Mirror's angle can be adjusted more widely.
The OEM mirrors on my Honda, Grom, and JC92 were difficult to see (and now that it's getting colder and I'm wearing a fuzzy jacket, I'm sweating even more because my body is reflected in the mirrors), so I switched to the Takegawa mirrors. So I installed a Tanax Spacer for height adjustment and this OffsetHolder, hoping for a wider range of Mirror angle adjustment.
With the OEM mirror, my eyes would often get tired, but now that the mirror is higher and my field of vision is wider, I can see behind me better and my eyes are less tired! I'm glad I did it, and I recommend it!
View detail
You're right to wear it.
I couldn't see behind me until now. (LAUGHS)
After installing it, I can see some of it.
Of course, you need to pay attention to 360 degrees while driving, right?
If you can't see it, it's dangerous.
We want to reduce blind spots as much as possible.
I can't deny that it's a little stiff, but it was the right decision to wear it.
This kind of thing of Tanax…Even the screw part is painted thickly, so I'm worried about it because it doesn't feel tight as Snap, but I can use it anyway.
View detail
It's easy to check behind you.
I'm currently replacing it with a Takekawa Mirror, but it's still hard to see backwards.
This time I added a 45mm OffsetHolder.
It will look a little ugly, but it will make it easier to do a backward check, and Stress
has been reduced. I would recommend this product to anyone with the same problem.
View detail
It's easier to see.
D I put it on the Tracker 125, Mirror has changed it.
Since Mirror can be moved outward by 5cm, Quantity:Pair (for Left and Right) Both of them became very easy to see.
View detail
I'm glad I put it on, but...
Used on CT125.
MONKEYetc. seems to be the same, but Quantity:Pair (for Left and Right) The Mirror is installed in a different position on the
I added it because I thought it was hard to see Mirror on Left.
Mirror position is in Quantity:Pair (for Left and Right) It turned out almost the same, so the effect is as expected.
I don't know if it's the spec or the individual difference, but even when I tighten the screw tightly, there is some rattling and the mirror shifts a little bit after a long run.
I'm using it as is because it doesn't make the Mirror wobble and I can put it back in easily by hand, but it would have been better to put a Washer or something on it.
View detail
Offset outward to make it easier to see behind you.
[How is it used?
I have it on my D Tracker 125.
Mirror is KITACO Z2 Mini Mirror Short Bracket.
Was the one you received as per Image?
It was well made as per the image.
Was the installation difficult?
It's Bolt On and it's easy.
How was your experience with it?
The D Tracker 125 and the Z2 Mini Mirror with the Short Bracket were not working well together, the Bracket was too short and only showed my arm. So I decided to offset the mirror itself to the outside and bought this product. Now I can see behind me.
[Was there anything that disappointed you?
It becomes a little whitish when it tans.
View detail
It makes it very easy to see behind you.
The Mirror on my JC92 Grom is hard to see, so I've replaced it with the PCXOEM Mirror, but it's still hard to see.
I bought this product because I don't do basic slip-throughs and I wanted to get it a little more outward.
You'll also need a height-adjustable Spacer for the Grom to offset the Mirror on the outside.
Since it hits Throttle WireGuide.
I also thought that Mirror was close, so I made it Offset to the outside and also Offset to the front.
This reduces the amount of eye movement when checking behind in Mirror.
Naturally, the protrusion from the body of the car becomes large, but it is very satisfactory because it becomes easy to see the rear.
View detail