【TANAX】Off-set Holder 45 Review
Best product!
I ride a current Z400.
Before installing this product, I could not even tell if there was a vehicle behind me, but after installation, I can see it differently and I am satisfied with Large.
If the price were a little lower, it would be a perfect score.
Responses
Other reviews
easy to read
I installed the mirror on my MONKEY125 because it was hard to see. The rearward view is not only easier but also extended to the front, so I can use it very comfortably with less eye movement. View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
TANAX OFFSET HOLDER 45
Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the side mirror visibility. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. -------------------------------------------------- -------- Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the view of the side mirror. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. Powered by Google Translator View detail
relief from a worry
I bought this for my CT125 because the LeftMirror is in a strange place and it was hard to see the back of the car.
I am happy with this Parts and it is much easier to see.
I was torn between 30mm and 45mm, but the 45mm is just right.
View detail
TANAX OFFSET HOLDER 45
125 years old, 125 years old, 125 years old.
I want to know more about this.
I bought the genuine Monkey 125 side mirror because I couldn't see the rear clearly.
After installing the offset holder, the mirror viewing angle will be good, allowing you to see what's behind you and drive safely. -------------------------------------------------- -------- The side mirror of the genuine Monkey 125 was purchased because it could not show the rear. After installing the offset holder, the mirror viewing angle is good, so you can show the rear so you can drive safely Powered by Google Translator
View detail