Reviews
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
Large recommendation for CUB for Touring
Rear suspension is available from various manufacturers and helps to improve the ride quality, but when it comes to for front suspension, there are not many options.
This product is a Reinforcement Spring, and it is exactly what I was looking for. It is a strong ally for long distance touring.
It's not a heavy load, but it's stable when driving (but not limited to) when loaded with cargo, and it's unobtrusive and sober.
I bought the Spring and replaced it myself. I only bought the Spring and replaced it myself, but if you are not comfortable with the work, you can ask Moldy to do it for you.
They'll do it.
View detail
![Knurled Aluminum Steps [R Type].](https://global.webike-cdn.net/photo/impression/6e/6e9f13b2beb17889543b504019556e09L.jpg)
Fits: HONDA CHALY, HONDA MONKEY, HONDA CUB90
Design is good
This is a Recommendation because it is cheap, easy to work on and easy to ride. View detail
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
Front stiffness is increased.
Because NORMAL was too soft, and there were a lot of near-misses such as the road surface Gap.
I decided to go with a stronger suspension, so here it is.
good point
The stiffness is increased by about 30%.
The car will not be shaken by the Gap on the road.
Reasonable price.
A bad point
The front suspension is located at the back of the car, so it is difficult to install and remove.
The installation was Large strange, but the effect is perfect.
You will be rewarded.
If you're riding a long way, road Gap and all, the original suspension feels scary, so if you have those complaints, RECOMMENDATION!
View detail
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
Resistant to rust
I used to use the Plating type, but it rusted and I bought this product! View detail
After searching all over Home center, I found it!
In order to load NSR50 into Toyota Pixis Van (HIJET Van), I looked around Home center, but I couldn't find 1,25 Pitch1,5 of M8 everywhere, when I was at a loss, I found it at Webig. (laugh). I replaced the mounting bolts on the inside of the seat railRear of the driver and passenger seats, and made a cut in the floor carpet. The Pitch1,25 of M10 which I have was installed in the Seat belt installation part of the driver seat and the passenger seat. If it is NSR50 with this, two cars can be loaded. View detail
Increased loading capacity when camping touring!
Since I replaced my CUB110 with a JA44, I also re-purchased this Cuby Front carrier.
I bought the Repeat because I had used it for my previous JA07 and was satisfied with its shape and loading performance.
It is just the right size for loading Schlafsacks and Tents for camping tours and has a hook for stable loading.
When you don't have any luggage on board, the weight may increase a little, but it is not so much that the handling is worse. As expected of the CUB specialist, Cuby has thought this point out very well.
But I use it on my daily commute to work and it rusts in the rain.
This is an inevitable part of the Material, but it's a hassle to maintain, so I'm leaving it as it is.
Anyway, my belief that the best choice for CUBs is Cuby's products is unquestionable.
View detail
Fits: HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub]., HONDA LITTLECUB [Little Cub]., HONDA PRESSCUB [press cub]., HONDA CUB [Cub].
It's solid, but the Balance is a Large thing!
Fluffy feet will be Snap and used impressions. Balance and balance is still bad because I rear suspension is still NORMAL; hell; I prefer to be installed after the conversion of the rear suspension is also mandatory to be understood beforehand. I installed it by myself. I did the installation by myself, but I tried to do it with reference to Net without the Spring compressor, but it was very large and strange; (Unless you have a spring compressor.)
The price is cheap, so it's in Recommendation.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I'm normally attached to it.
Installation was normal, I think it would be a good idea to replace it with the front fork OH.
This is the price, but you can clearly see the difference. The difference is very clear.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
Large satisfaction with outstanding stability
Normal look is what I'm obsessed with, but for the 88cc engine, it's Normal The fork is still unstable
I found this product when I was looking for reinforced parts for driving stability
How did you feel after the exchange? "Outstanding stability It was
I'm really happy with the enhancements without ruining the look I chose the OEM Length, but I also have a choice of lengths, so I stuck with the Normal look I really recommend it to anyone who is
Spring replaced it himself, but I'll review the work
You can find out how to exchange it on the Net
MONKEY OEMFront Fork Spring Replacement
You can check a lot of things by searching for
We recommend replacing the following parts at the same time, as they are almost all Rose The part number is the OEM product number
Quantity:2pc. Each set is required
?ForkGuide (Part #:51502-045-670)
Dust Seal (Part #:51503-165-003)
PistonSlide pipe (Part #:51507-098-000)
?PinSpring (51526-098-000)
? , ? is Quantity:This is the one in the 1pc. eye photo
I bought these two at the same time as Spring
However, in the process of roasting, the plastic bottle broke off (see the third picture) and I had to order more in a hurry I had to order more in a hurry (the third picture)
? looked like it could be reused, but I didn't want to make another mistake, so I decided to replace it with them
Even on the Net? It is a good thing that I was able to get a good idea of what was going on, because I thought that I was going to be able to get a good idea of what was going on
I ended up having to wait a few days for the second picture
One of them didn't break, but it was pretty degraded, so I'd recommend buying it from the beginning It is
Spring is Quantity:1 Set of 4pcs. it installs to wrap around the parts in the eye picture, but
Check the inside and outside of the fork to make sure it is facing the right way
Install the spring while adjusting the orientation
A similar part will be attached underneath the Spring, but you'll have to check the direction of the pin holes to make sure it's facing the same way Install
Quantity:1 Set of 4pcs
Once the Spring is assembled, grease it well and restore it
There are many different types of grease, but I used a generous amount of Urea grease to restore it! It was
I hope you will join us
It takes quite a bit of time to do the work carefully, but I am satisfied with the changes after the replacement
View detail
Fits: HONDA MONKEY, HONDA GORILLA
OEMFork is changing radically!
Although I'm sticking to the normal look, I'm not sure if it's possible to run the 88cc engine on the Front The fork was poor and I bought it for driving stability
It works great! The ride was so stable that I wondered what it was before I chose the OEM Length, but I also chose the Normal Length because the price is cheap If you're obsessed with the look, I would highly recommend it
I'll include the points of my replacement
I hope you will make it a point to join us
How to Exchange
There are not many ways to replace it, but it is introduced on the Net, so if you refer to it, the work is not so bad It's not difficult
However, the parts to which the spring is attached (the parts on both ends of the spring in the second picture) have different orientations When restoring it, check the inner and outer sides of the fork and adjust the direction of the hole and protrusions Install the spring
The part that attaches to the top of the spring has a protrusion on the inside that indicates its orientation Quantity:(1 Set of 4pcs. eye photo)
Parts
I recommend Overhaul while you're at it, as I'll lose almost all of the Spring exchange It is
The OEM Parts part numbers are listed in the Join section
Dust Seal (OEM Product No. 51503-165-003)
?ForkGuide (OEM Product No. 51502-045-670)
PistonSlide pipe (OEM Product No. 51507-098-000)
PinSpring (OEM Product No. 51526-098-000)
Quantity:2pc. Each set is required, so please pay attention to the quantity when ordering
? and ? Quantity:These are the parts in the 1pc. eye photo
? and ? I bought it in a hurry because it broke when I lost Fork There was an introduction such as the crack in Net, but it was thought to be Large sturdy, but as expected It was cracked, and it was also quite deteriorated …^^;
? and ? will have to wait for the state of the second picture if you don't receive the ? Recommendation
? looked like it could be reused, but I didn't want to make another mistake, so I made a new one just in case
Grease!
I selected Urea grease
View detail
Fits: HONDA MONKEY, HONDA GORILLA
The price is good
I replaced them together when I did the Front forkO/H on the AB27 PartsForkGuide, Pin, Dust Seal, C-ring, C- ringWasher, buy the slide pipe and start to work It took me about 15 minutes to make it, but I put it between the Vise and the normal spring to remove the normal spring and turned it the wrong way It takes a long time, and finally, you can't take it even if you turn it, even if you hit it, so you can't get it off with Leutor After removing Normal spring, I used CubyReinforcement I put Spring in and then applied Grease with Fully, and then the reverse when I removed it If you put it together in Pattern, you're done, and by the way, it was really easy to incorporate
The first thing I thought about when I installed it was A - before driving, I put the front brake on the front fork to raise and lower the front fork I'm glad I put Grease in with Fully, which is hard anyway when I did the B-Running feeling is the squishy feeling of Normal spring (No Steering Damper) It is C-8InchTire that will be gone, so until now it is adjusted with Steering Damper It has become better to run it plus
Finally, the packaging is better than some of the companies that deal with CHINA, and Cuby's If there's something I want in a product, I'll buy it on the spot
View detail
Fits: HONDA Super Cub 70, HONDA Super Cub (HA02), HONDA Super Cub (C90 type), HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub]., HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub].
Cap Nut & Washer for Honda Super Cub
I purchased this set of stainless steel bolts and washers to replace old original parts that were corroded and badly worn, the quality of these parts turned out to be very good, the stainless steel is thick enough to withstand the required forces. The installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for the fast delivery and great packaging! I purchased this set of stainless steel bolts and washers instead of old original parts that were corroded and worn out. The quality of these parts turned out to be very good, stainless steel of sufficient thickness to withstand the required effort. Installation of these parts took about 10 minutes. With these details, my Super Cub looks even better! Many thanks to Webike for fast delivery and excellent packaging! (Translated by Google Translator) View detail
![Knurled Aluminum Steps [R Type].](https://global.webike-cdn.net/photo/impression/17/17a8fc01a445cd5e817dc33214f8031eL.jpg)
Fits: HONDA CHALY, HONDA MONKEY, HONDA CUB90
Good Cost performance
The exchange from OEMfootpeg, custom made Appeal feeling is good. By the way my own LITTLE CUB, because the body is vibrating so much I wore a tightening Bolt on the back of footpeg with a screw lock with a loose stopper. View detail
Fits: HONDA Super Cub 70, HONDA Super Cub (HA02), HONDA Super Cub (C90 type), HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub]., HONDA little cub, HONDA Super Cub 50 (C50 type), HONDA Super Cub 50 (AA01), HONDA SuperCUB110pro [SuperCUB110Pro]., HONDA SuperCUB110 [SuperCUB110]., HONDA CUB [Cub].
Is good
I was looking for something that will not rust as it will run on the mountain with CUB and become muddy.
It was not possible to attach it to the clipping point on hand, the Up type muffler of the water circle RACING.
The water head Racing Up Exhaust System may be used if there is an ultra thin socket?
View detail
Fits: HONDA GORILLA, HONDA MONKEY
According to Overhaul of Front fork
After replacing the Rear shock, I became more aware of Front's poorness,
Also, curing of Dust Seal - Crack crack, Grease leak was also terrible,
Overhaul In addition I introduced Reinforced Spring.
OEM Length (30% strengthening) Although I put things of,
It became solid and stable, stable - I feel secure..
Since the work process and the tool to be prepared falls a lot on the net, it is omitted.
Upper / There is some hang to desorb Spring from LowerSpring holder.
Between the desk vice, we strike the conch and Spring end part with Graver or Slotted screwdriver.
I do not need much power, but I can not come off unless I hit it to some extent.
Even when you wear Reinforced Spring in Holder,
Spring with vice and turn Holder in Wrench, you can incorporate it in the lake.
Because I did not take out the Spring end BALI,
Although I scraped the Holder with crackling, I installed it without worrying about it.
Perhaps you should treat the neighborhood as a chitin.
Also, assuming Wheel assembly time, the orientation of the Inner pipe - It is better to pay attention to the angle.
If you prepare the tool properly in advance, the work itself is not difficult at all,
I think that it would be better to replace the OEM Parts Number as a part of Overhaul, but to feel the benefit of Reinforced Spring more.
Finally, since the work is endless, it is black and it is attached with an old Grease like a mass of mud,
It is good to prepare Dustcloth for more.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Type A MONKEY (Z50Z) It is also Exactly.
Front fork's decomposition I damaged OEMSpring at OH and thought about repairing with OEMSpring, but sometimes prices did not change so much, so I decided to try OEM Length's Reinforced Spring.
Small raw MONKEY does not fall under conformity model because Rear is Rigid's type A, but it is not suitable for conforming models, but MONKEY after J type and shape - Since Length is the same, it can be installed as it is.
Because Rear is Rigid, I thought that if you harden the Front it might splash with Solidly before fitting, but rather it seems that Balance before and after it seems to have been taken, on the paved road the riding comfort is also reduced by the amount of reduction in front and rear Pitching It was surprising that I got better.
If you do not mind the OEM Parts Number, I think this Spring is preferable.
View detail
Fits: HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla]., HONDA MONKEY [MONKEY]., HONDA GORILLA [gorilla].
Used with GORILLA
OEM's Bolt got rusted, so I bought it as a Stainless Steel if you exchange it anyway.
It becomes OEM's 14 to 17 mm, torque is easy to put on, it looks better.
Size is not sold to Home center.
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
Cospa best. Large satisfied
Mounted on 1995 model HA 02 type CUB 90.
With no manual, it takes a while to install for the first time.
Excellent for Cospa Large I am strange.
Also, you can use Center Stand firmly.
Image reference. (*^-^*)
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
Attached to CUB90DX
Discovered while considering Other Company Product because the hole in the OEM's Exhaust System has been opened.
With tens of thousands of yen for other company's Exhaust System, All Sten's Exhaust System.
Can not you use Center Stand by watching other people 's impressions?
I thought, but I am using it.
When Spring of Center Stand and Exhaust System are used when using STAND, there is no problem during running.
Since there is no problem with this interference and running, the one who does not mind is cheap and it is solid and it is recommended because it can use Center Stand.
Although it is the sound to worry, when using Baffle it seems like a little noisy number of Popokopo and OEM.
I am here now.
Removing Baffle makes it sound like a 250 CC single cylinder.
It is thick..
It will notice even if you are running on the Large Ki-no-dori.
It is recommended 1 pc.
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50
It is good.
There is no particular problem.
The sound is Large and bass is strong. Turning on Baffle makes it quite quiet.
The surface is beautiful Gold belonging gloss, there were about 2 scratches not to know without looking.
Spring of the coupling part was tight and the installation was a little Large strange.
Overall, I am very satisfied..
View detail