Reviews
Fits: HONDA MONKEY
DAYTONA's Copy product?
DAYTONA's Copy product?
The quick quality is not bad, but it is Solidly and hardly Stroke due to Lowdown.
The screw thread on the spring that holds the spring to the top bridge has been licked, but DAYTONA's hydraulic inner fork repair item can be used. (The size of the spring winding is a little different, so some modification or hard work is required.)
Brembo caliper support for DAYTONA Inner Fork can be used without modification.
View detail
The miscellaneous aluminum fabric looks good on the contrary.
The result is an old-fashioned look, like an old Cafe racer.
It's really messy and uncomfortable to install, but it installs properly.
It is cheap and can be installed in the part where the part after the exhaust system of MONKEY is replaced became scant.
View detail
For now, I used it for Custom
I bought this to install a 22.2 diameter Handlebar to customize it.
Only Universal Product used a different Bolt, which required a little ingenuity.
The price is affordable, so it's good for those considering Custom.
View detail
For the MONKEYWide stem!
i installed it for the gcraftWide stem with 245mm under the neck of the attachment, but the Bolt of Nut It only takes half a screw thread The bolt head came out with room to spare:Pair (for Left and Right) Washer bite is just fine View detail
Is good
I bought it to build MONKEY from scratch
Installation to the Frame is not a problem (no processing required)
Since the mounting holes do not match with the mounting holes of a handheld OEM tail lamp, mount it via a flat angle
What is the plate (with screw holes) on the top of the Lamp (under the carrier surface)?
I'm glad I don't have one, so I might cut it out with a sander
(It's not a functional problem if it's there.)
As it is being assembled, it has not yet been used in practice
View detail
If it's a Chinese party, it's good
Raw and pimped out for Chinese Parts
As the Center of Tire is out of alignment, adjust the universal collar while shaving right underneath
I was able to continue using it until the car was scrapped with no problems running as long as it was installed properly to some extent
View detail
BALI is still there, but it's worth the price
There was leftover BALI processing on the rim of the wheel
The fit was perfect, no Gap etc
I think it's a good product considering the price
If you're interested, you can't recommend
View detail
Warmth
After changing to GM-MOTO's Swing Arm, it is possible to use it with the OEM
Shortening the time frame increases the amount of work we have to do If you are introducing the Swing Arm, please explain
I think it's better to buy them together
That's what I thought, and I'm buying more
Unfortunately, I thought the quality was poorly made
In the future, when you replace the Tire, I think it can be serviced by the normal process
View detail
GM-MOTO Lowdown Diamond Cut Seat - For DAX / 12v Copy
GM-MOTO Lowdown Diamond Cut Seat Good quality product for price but not great. Seat is made with vinyl and all visible components seem to be quite good quality and visually appealing. Important to note diamonds are not actually stitched so it's waterproof. Can't report on fit for original Honda Dax. I fit to a Skyteam Skymax (Also has other names Eg Pitster Classic). Fit wasn't perfect, bracket that comes with seat can be used but using the original Skyteam bracket has a better fit. Locking locating pins are better used from original Skyteam seat. Rubbers must be removed and orignal rubbers can fit. All brackets/attachments were swapped without issue. Battery box also MUST to be removed or modified for the seat to sit correctly. Battery can sit in frame with foam support or bottom support of battery box extended or cut off. Once these modifications are made seat sits quite well but slightly short at rear in my opinion. View detail
![Aluminum Swingarm Type G [Disc Type] for APE](https://global.webike-cdn.net/photo/impression/40/40ebb5f8eb18c5f40218ea3f15208719L.jpg)
I love it because it seems tightened.
In assembly, the rear wheel Shaft is too long for the OEM 2. I bite a Color of about 5 cm. Also, I put a 5 mm Washer between Swingarm and Tire to match Chain's Line.
I'm happy to be honest a little lighter. Even if we have both, we feel that weight is not much different from OEM's Swingarm.
View detail
Speedo
Not sure if it is accurate, but it fits and looks nice in the headlight I also bought from webike. 1972 honda z50ak3 that was made in japan View detail
Good for price.
I am using 4? Long. Because we are loading NSR's Tank, we purchased because Seat is shifted backwards. Balance, cospa, texture are both satisfied well. View detail
Just right for everyday use
Buy DAX's Rear wheel a bit to make it a little wider. Although a nude part was seen in the finish of cutting, there was no problem in using it without distortion or hole misalignment. Size was also just right, so I will continue to use it and I want to see a state. View detail
Easily become wider
Purchase for DAX Rear wheel Wide. Recently, 1Quantity : Although 2pc stop seems to be popular, it seems that there is no problem so far for the ordinary use even for stopping eight here. Although the gap with Chain line was sufficient, it seems that it is necessary for machining such as scraping etc. in some cases because Bolt which stops Torque rod of Rear brake is narrowing gap.
The Minus point is a place where BALI is somewhat large, but it is good when thinking about price.
View detail
Left (Battery side) Use only
Right Side does not use because it is equipped with Catch tank.
I only use Left, but Large Kimono is also good looking.
I think that there is not a high Manufacturer object and a Large difference.
Of course it is okay not to injure those who do chamfering simple corners,
Even if you buy high items, I think that some maintenance is necessary as well.
Just to fix it to the car body is fixed with three claws,
Since there is no flexibility like Plastic, it is hard to fix it if you do a little gap.
It's pretty delicate but you can adjust it so let's do the final tightening of Bolt at the best position.
I think that it would have been a little lighter if they could sell one by one if possible.
View detail
A very helpful all-in-one product that comes with everything you need if you plan on doing a restoration. It comes with the full wiring harness a full lock set including the key switch, petrol tank cap, steering lock and the helmet holder. The electrics a
A very helpful all-in-one product that comes with everything you need if you plan on doing a restoration. It comes with the full wiring harness a full lock set including the key switch, petrol tank cap, steering lock and the helmet holder. The electrics are also included like the horn, cdi, distributor, regulator and spark cable. Also included are the the right and left switches with new grips. A problem I had was with the CDI as it was misfiring, however I don't have the original engine, and my friend with another engine had no problems. One thing that really annoyed me with this kit is that the left switches have an integrated clutch lever, but the the right switches don't include a brake lever as you can see in the pictures. Maybe they thought about people who install aftermarket brakes but an alternative should be provided. Other than that it is great value for money. View detail
Fits: HONDA GORILLA 12V compatible, HONDA MONKEY 12V compatible, HONDA GORILLA 6V compatible, HONDA MONKEY 6V compatible
The main part of an Oil cooler thinks whether it is inexpensive without crushing of a Core etc. Merely ..... The negligent degree which carried out alumite treatment with a BALI of the Banjo bolt is Chinese touch.Since Pons attachment was slig
The main part of an Oil cooler thinks whether it is inexpensive without crushing of a Core etc.
Merely ..... The negligent degree which carried out alumite treatment with a BALI of the
Banjo bolt is Chinese touch.Since
Pons attachment was slightly dreadful, it BALI-picked lightly and attached it.
View detail
Good pedal for hydrolic brakes, you might need to bend the bracket for the spring a bit inwards, and the brake lever (back end) a bit to get in line with the hydorolic cylinder. for the rest it worked fine for me.. nice quality for that price.. del
Good pedal for hydrolic brakes, you might need to bend the bracket for the spring a bit inwards, and the brake lever (back end) a bit to get in line with the hydorolic cylinder. for the rest it worked fine for me.. nice quality for that price.. delivery time was within a week and a half.. View detail