Reviews
Fits: DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI STREETFIGHTER V4S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4
Wiring ingenuity required
The original wiring is surprisingly long and there is almost no space for it.
If possible, I would like to see ShortWiring or a storage boxetc. on the back of the number.
Also, it was difficult to understand where to use the original screws and the screws that came with the product.
It would be even better if the Number angle could be adjusted.
I dare to be harsh in anticipation of Moto Crazy's future.
View detail
Fits: DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI STREETFIGHTER V4S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4
Can Refreshing the Rear
[How is it used?
The state of the OEM was not to my liking,
I installed it immediately.
Was the one you received as per Image?
It was exactly what was listed.
Was the installation difficult?
Torx wrench is required to remove OEM Parts.
Also, since the application of Screw lock is described for tightening,
We prepared this one as well.
DUCATI's License Frame is handled by drilling some holes in the frame,
Double-sided tape fastening without screw tightening was fine.
How was your experience with it?
OEM condition is unknown, but Rear tire sprung Small stone, etc.
Protection film was applied to the Tail lamps.
In addition, the OEMReflector had a crack in the threaded part of the OEMReflector at that time,
Replaced by DAYTONA.
If the Tail cowl is to be removed, it will interfere with the Tail cowl,
The Fender Eliminator must be removed first.
[Included Parts:were they on?
It comes with a handling Instruction Manual and several screws.
[Was there anything that disappointed you?
Not particularly.
View detail
Fits: DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI STREETFIGHTER V4S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4
Cost-effective standard parts
Was the one you received as per Image?
The parts are carefully packaged with instructions and stickers×2.
Was the installation difficult?
If you follow the instruction manual, there is nothing difficult. However, when removing OEM parts, in addition to various hexagonal bar spanners and ordinary spanners, 2 sizes of Torque are required, which may be a little expensive if you need to purchase tools.
How was your experience with it?
The rigidity is solid, and the Blinker, which was PullPull all the way in OEMFender, feels fixed without shaking. (I think it is simply because the distance is shorter.)
I think it is good to be able to freely adjust the angle of the License Plate and the height of the mounting position. (I am a vulgar Stylele who fixes it in the shortest position.)
[Included Parts:were they on?
No Bolts were missing and there were no problems.
[Was there anything that disappointed you?
Nothing in particular, I have driven about 100km and there is no loosening of Bolt or Gap of Blinker or License Plate.
Point and hang of installation
When installing, it takes a bit of hang or large boldness to push the excess length of wiring into the tail cowl. There is a gap to push the wiring downward and upward, so it can be pushed into the cowl without breaking.
Availability and clarity of Instruction Manual
Naturally, the translation (please enter here, and there are several diagrams, so if you can read the assembly diagram of the Plastic model, you should be able to understand it without any problem.
Points to note
Since the OEM rubber bush is used in place of the OEM one, I thought that the rubber might crack during removal and installation if it has deteriorated over time. This is not a process that can be repeated too many times.
Opinions and requests to Manufacturer
Since the angle adjustment of the License Plate is stepless, I think it would be reassuring if they could tell us which angle would pass vehicle inspection if possible. (I guess if you are afraid of vehicle inspections, just go with the OEM)
View detail
Fits: DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI STREETFIGHTER V4S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4
The first Custom came from Fender Eliminator
It is inexpensive, and since the appearance is hidden by the Number, I don't worry too much about it. View detail
almost
S1000RR 12MODEL.
The Body is well made. If you are not dissatisfied with the shape, it is a good product. It attaches quickly.
The assembly is a bit annoying because of the large number of parts, but I chose it because it offers more flexibility in combination than the oddly integrated parts.
But personally, I find it a bit tacky.
Below is a list of areas that I thought were subtle. I did not feel that the quality of the product was not good enough, as it was all a matter of taste in design.
License Plate Light is very bland.
The design of the Fender Eliminator is a bit inward, but it looks as if the OEM's bloated License Plate Light has been transplanted. I couldn't put it on myself.
Reflector is on top.
→KitSingle Item:This is not so noticeable when viewed as a single item, but when attached to the car body, the reflector is on the top and the number is quite a bit lower, resulting in a blurry image. It's a good thing that the Fender Eliminator Kit is so good. 。 The number position does not change even if it is removed, and it was too much trouble to try to force the number up, so I gave up.
Blinker Bracket is very prominent.
I'm not sure if it's the Fender Eliminator or the Blinker Bracket, but it seems to me that the Blinker Bracket is very, very insistent. I decided not to use it.
These are the points that I personally thought "hmmm", but if you don't mind, I think the quality is good enough to buy it and put it on as it is. At least, I don't think it's a "HaGap". I think the quality is good enough for people who don't care about it to buy it and put it on as it is.
I hope this will be helpful.
View detail
Fits: DUCATI Monster 821, DUCATI Monster 797, DUCATI Monster 1200, DUCATI SUPERSPORT 950, DUCATI SUPERSPORT 950S, DUCATI SUPERSPORT 939S, DUCATI SUPERSPORT 939, DUCATI Monster 1200S
Homework 1
Somewhat fiddly!
However, it is highly complete.
View detail
Fits: DUCATI Monster 821, DUCATI Monster 797, DUCATI Monster 1200, DUCATI SUPERSPORT 950, DUCATI SUPERSPORT 950S, DUCATI SUPERSPORT 939S, DUCATI SUPERSPORT 939, DUCATI Monster 1200S
It took a lot of work, but Parenthesis is great!
The M821 has a complete design including the Rear Fender, but I still want to make it a Fender Eliminator and have it Refreshing! I bought it because I thought it would be a good idea.
The installation itself was easy, but there were a few troublesome parts that took longer than expected.
I had a hard time 1. removing the pure normal thread screw in the bracket of the blinker and 2. screwing the body of the Fender Eliminator onto the body. I think we can proceed.
Also note that drilling is required when using OEM License Plate Bracket.
View detail
Fits: DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI STREETFIGHTER V4S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 Speciale, DUCATI PANIGALE V4S, DUCATI PANIGALE V4
A DUCATI classic
I chose this because it is a standard DUCATIFender Eliminator. I think that there is no problem including the angle etc. though there is a slight difference from other manufacturers. I had it installed at the time of delivery this time.
When you install it by yourself, it is not difficult work if you refer to the Net video etc.
View detail
Fits: DUCATI SCRAMBLER URBAN ENDURO, DUCATI SCRAMBLER ICON
DucatiSCRAMBLER
I use the OEM License Plate Light, but it is not Stylish. The mounting bracket is Quantity:Pair (for Left and Right) I'm not happy that they are separate and hard to match. View detail
Fits: DUCATI HYPERMOTARD821, DUCATI HYPERMOTARD939
Rear fender-less for a more racy look
It is Moto Crazy's Fender Eliminator for Ducati, I used it for MONSTER1100evo, it is also good for HYPERMOTARD821, and it refreshing the rear very much. The price is cheap, and it is preeminent coolness thanks to the composition of the Parts of the minimum necessary for me personally. View detail
Fits: DUCATI Streetfighter S, DUCATI Streetfighter, DUCATI STREETFIGHTER848, DUCATI Streetfighter S, DUCATI Streetfighter, DUCATI STREETFIGHTER848
Large sturdy if you look at the Instruction Manual properly.
AssemblyInstruction Manual is included and it was relatively easy to replace the OEM Blinker.
LED Sequential Blinker (Rizoma (Part Number)):(FR130B)), I had considerable difficulty in replacing it.
The cord storage space is too small and the cords for attaching the resistors are too bulky to store.
So the resistor was connected to Front and somehow completed. But then...
When I assembled all of them, the license plate hid the blinker.
So furthermore, Posh (POSH) I bought an extension bracket 40mm for sequential.
All redone. I enjoyed it for a few days.
View detail
Fits: DUCATI PAUL SMART1000LE, DUCATI SPORT1000, DUCATI GT1000, DUCATI SPORT1000, DUCATI GT1000, DUCATI SPORT1000
Refreshing around the rear!
Although it is not written in the manual, I think that it takes a little time for a beginner because there is an installation order. I think that it is somewhat easy to assemble if you fix the back part that cannot be retightened afterwards first, and proceed with the temporary tightening of the others.
The workmanship is not bad for the price, and Refreshing around the Rear.
View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1299Panigale, DUCATI 1199Panigale, DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1299Panigale, DUCATI 1199Panigale
Cost-effective!
Many external for vehicles are expensive, using imported products and carbon parts, but I have no complaints with this one The Panigale is a Tail Lamp and Blinker in one piece, and the BlinkerLight is The type that doesn't protrude from the body is popular, but I'm using the LED type of OEM It is very Compact and does not interfere with the body design It is very Compact and does not interfere with the body design I think it's safer because it's easier to check than it is to check the Number angle and the quality Not bad
It's a good costumer!
View detail
Fits: DUCATI SCRAMBLER URBAN ENDURO, DUCATI SCRAMBLER ICON
Refreshing around the rear!
I installed it on my Ducati SCRAMBLER
I'm glad to see the rear area refreshed so much
The installation process was very easy and only took about 10 minutes
View detail
Fits: DUCATI MONSTER 1200, DUCATI MONSTER 1200S, DUCATI MONSTER 1200, DUCATI MONSTER 1200S
Good only in use
It is a rare motorcycle called MONSTER S21200Setc The lack of explanation of the Instruction Manual is a big no-no Because the point that should be the point is not written, many times it is impossible for an amateur to put on and take off the bike It's not easy for an amateur The fit is good Because it is covered by the tail lamp a little, it is the best if it is lowered 1cm later Because there are too many screws, I am worried that it may fall off one day It does its best by tightening the screws View detail
Fits: DUCATI SCRAMBLER URBAN ENDURO, DUCATI SCRAMBLER ICON
Convincing Products
It will be installed on the 2019 New Model SCRAMBLER Icon
When I checked with the manufacturer, they said it would fit the New ModelIcon Purchased
I can't wait to install it because the rear area is Refreshing
View detail
Fits: DUCATI Monster 821, DUCATI Monster 797, DUCATI Monster 1200, DUCATI SUPERSPORT 950, DUCATI SUPERSPORT 950S, DUCATI SUPERSPORT 939S, DUCATI SUPERSPORT 939, DUCATI Monster 1200S
Blinker from Ducati Performance cannot be fitted
The texture of the product is very good, there is very little BALI! (There is a little BALI in the drilling part.) 。 However, because of the Bolt's method of fixing the Blinker, the DucatiPerformance Blinker cannot be installed View detail
Neatly organized around the rear
It took me a while to remove the OEM Fender? Refreshingly, it's nice to see the License Plate Light connected We need to do some processing, but I've been using commercially available Waterproof I changed to Connector and made the coupler to insert and remove the license plate The Cable of the License Plate Light of the product is short, and I am worried about the cable of my F4 In the event that the engine cannot be retracted to the body (under the Tandem seat), the Exhaust There is a hole for the Cable in the SystemCenter area, and the Connector section comes in the hole for the Cable It's not a good idea Cable length should be 15-20% longer than that of the original It's a good way to get it delivered View detail
I'm satisfied with Refreshing Design.
Because it is a type without angle adjustment, it will be a finish that is very refreshing.
However, I feel that the angle of Plate does not match a little with the body of Sharp Design of Seat Cowl, but there are restrictions and restrictions.
Installation is not so difficult, but I had to cut off the car Both SidesLicense Plate Light's Wiring and I hesitated a bit about cutting the new car Wierding just delivered.
The product is solid and made with a thick Plate so it will not stick around while traveling and I am very satisfied as a result.
And, most of all, the packing condition was very good, I was surprised to see that beautifully about the Corrugated cardboard of the outer box was closely tightly closed as it was contained in each bag one by one.
Just looking at the outer box made me like this Manufacturer.
View detail
The location of License Plate Light is ...
Mounting on 16 year model S1000RR.
Installation requires OEM Rubber Push relocation or disconnection of License Plate Light Wiring → Installation, so if you are not familiar with it, you'd better ask Shop to ask.
Styling after installation becomes Race ish atmosphere and it is very good.
Unlike Aluminum, because it is Stainless Steel, there is no need to worry about breakage due to Gold genus fatigue due to vibration, and it is also easy for self-propelled faction to remove Blinker and Number by Circuit travel etc.
The drawback is the increase in weight due to Stainless Steel and the position of the product's License Plate Light.
Because the weight increase of Fender itself is not the weight under Spring, I think that it is necessary for the general public to care.
The problem is License Plate Light attached to the product, this is the current law (Number violation obligation) There is a high possibility of conflict with.
Because the attachment position is close to Number, & Number angle is oblique so the place name Number gets hard to see a little.
This is because there is a possibility that the place name Number may not be completely seen from a car with a high car height, and it is considerable GrayZone against violation of display obligation that crackdown became severe recently.
As Material is Stainless Steel, I think that if you make a little processing and make it a little easier to see, there is almost no problem.
(Although it is a digression, I did not dislike the form of OEMFender, but I fixed it back because the problem of contact with Blinker occurred in & Pannier case installation)
However, since it is a well thought out product as a whole, Recommendation can be done.
View detail