Reviews
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
When connecting the Battery terminal
When connecting to the Battery terminal, it is recommended to use round terminals instead of Y-type terminals.
Not sure if Plating in Gold color is required or not.
Electric Works Pliers are required when Cable is connected.
View detail
Economical for repeated use
Economical as it can be used repeatedly by replacing the batteries without expiration date
Magnet is included in the bottom of the body, so it can be attached to the Gold part of the body.
I think it is a good idea to have it along with PurpleSaver.
It conforms to MLIT safety standards, so it is safe to carry in a car.
The +− notation on the dry cell batteries is difficult to read.
View detail
Lining Peeled Off Tool, but also useful for peeling off the exterior
The product name is Lining Peeled Off Tool, but it is also useful for removing the exterior.
There are two types of shapes, and the principle of leverage makes it easy to apply force, but it is likely to break if force is applied too much.
It's better to break it before the exterior cracks, though,
PushPins and other difficult-to-remove items can also be removed.
When using the product, cure the contact surface with Curing Tape, etc. before use.
View detail
Where Solder is connected, etc.
It can be used for branching connection with a solder, protection of Cable, etc.
It would be better to shrink them with a heat gun, but they are shrinked by lightly frying them with a lighter.
Be careful not to put the flame too close to it or it will melt.
View detail
put together in a presentable manner
Recent Small blinker wiring is ultrafine
It's as if it would tear into a thousand pieces if you applied a little too much force.
If you attach it as it is, it will surely break off.
And it looks bad Parenthesis.
So I reinforced it through Tube.
Finished by decorating with an Amigumi Sleeve
Just this much will make it look so much better.
It's definitely better than the BlinkerWiring roundup.
View detail
1pc. is useful for various purposes
[How is it used?
I bought it to use as a Drain pan for Oil change.
Oil replacement
Chain cleaning
Parts and tool storage for replacement of OthersParts
It is used for
Was the one you received as per Image?
I thought it was smaller than I expected, but considering that I was going to put it under the belly of the Panigale, 5LiterSize was just right in terms of Clearance.
How was your experience with it?
Oil replacement
In the case of Panigale, it produces about 3.5 liters of waste oil, but the weight of the oil causes it to deflect quite a bit.
There is a scale, but it cannot be used as a scale because there is only a line in one place.
Chain cleaning
I also use it as a receptacle for chain cleaner during chain cleaning. the size is just right and the area around it is now dirt free.
Parts and tool storage
When replacing or removing parts, it is easy to keep bolt nuts, etc. in the box and organize them without losing them.
[Points to note]
Material:It's not like a Stainless Steel pan or something, so I think it might deflect and spill if poured in parallel.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Quantity for Motorcycle also concerned about car inspections.:2pc. Buy the set
The smoke bomb had expired at the time of the inspection, and at this time, the smoke bomb was for Motorcycle and Quantity for Vehicle.:I bought 2pc
There was also a separate LED light, but I have a regular light separately, so this is the one I used this time.
Light intensity is satisfactory.
The included batteries are for test use and may not last very long, but spare batteries (Alkali AAAQuantity:I think there is no problem as long as you also have a 2pc) or replace it every 12 months or every inspection.
The texture of the lid is a little hard to open, perhaps because it is waterproof, and the "+" and "-" characters are hard to read for people with aging eyes. (Lol)
But the cosmetics are very good considering that they can be used for a long time after replacing the vehicle.
I also have an Emerson LED Sparkle light as a substitute for the triangular version, but it is best not to use it.
The Sparkle light is a very small size that goes under the Seat, but if you can fix it in an inconspicuous place such as inside the Cowl, we recommend that you do so.
Waterproof property seems to be quite strong, so.
View detail
It's strong enough.
In order to use the Portable navigator mounted around the Handlebar and the DriveRecorder (DAYTONA DDR-S100) mounted on the Rear as a Mobile Battery drive, it became necessary to install a Mobile Battery around the Handlebar. The need arose to install a mobile battery around the handlebar.
I wanted to be able to easily attach and detach the Mobile Battery, so I attached the mount of REC mount+ to the Handlebar Brace and attached the Attachment to the Mobile BatteryBody to be able to use it. I wanted to use an existing Attachment, so I decided to use a Smartphone Holder that I had left over.
I had a double-sided tape of 10mm width, so I could use them side by side. I had 10mm wide double-sided tape, so I could use them side by side, but I thought a single piece would be more secure, so I bought this Seat type.
Since it is for in-car use, it may not be good in the rain, but I don't ride in the rain, and since the Mobile Battery is not waterproof to begin with, and I intend to remove it as soon as it rains, I consider rain to be of no concern.
There is nothing special about this ordinary double-sided tape, so all you have to do is cut it out and paste it. The only things I took care of were to wipe the surface to be attached, this time both Mobile Battery and Attachment, clean and degrease them, and to work so that the tape would be attached in one shot to the targeted position. I also made sure to apply the sticker in one shot at the target position.
The price may seem high for the Size, but it is securely attached, so I don't think I will drop it while driving.
View detail
It's firmly attached.
I had a 10mm wide tape and could have attached it side by side with sufficient strength, but I decided to purchase the Seat type because I thought a single piece would be more secure.
Some products are labeled as heat resistant, but this product is also heat resistant. Operating temperature range -20 to 150 degrees Celsius. The product is designed to withstand even midsummer in a car.
This product is slightly thicker, and its elasticity and neSpringba make it more difficult to cut out, so the cross section will be rough if you do not work carefully with a well-cut Cutter.
The adhesive is strong enough. As a basic rule, degrease the surface to be pasted firmly, and work to paste it in one shot at the targeted position.
The price seems high for Size, but it doesn't seem to fall off while driving.
View detail
Powerful
I needed to reattach the Bracket to attach the Camera to the Helmet and purchased the Seat type.
I have been using a bracket of the type that can be attached to a rec mount in order to operate a Camera that is used as a DriveRecorder by attaching it to a helmet. Previously, I was using DAYTONA's DDR-S100 attached to the helmet, so the Bracket was originally attached, but it was removed when the helmet was repainted, so it was necessary to prepare double-sided tape to reuse the Bracket. To reuse the Bracket, we needed to prepare Double-sided Tape.
Since it would be very dangerous if the Camera were to fall out of the helmet while driving, we decided to use a strong double-sided tape and a single piece of double-sided tape.
If it is for the inside of the car, we had Seat type Double-sided Tape in stock, and it seemed to have enough adhesive strength, so we thought about using what we had, but since we cannot say that there is no possibility of driving in the rain, we purchased Double-sided Tape for the exterior that seems to be strong against wind and rain, just to be safe. However, since there was no guarantee that I would be able to run in the rain, I decided to purchase double-sided tape for the exterior that would be resistant to wind and rain.
Since this product is rather thick, it would be better to use a cutter that can cut well when cutting it out. In addition, although it is a basic thing, I think it is better to clean the surface to be pasted, to degrease it firmly, to paste it in one shot at the targeted position, and not to mess with it for about one day because it is not firmly attached immediately after being pasted. As for the cutout, the cross section was rough because it was inevitably cut by hand, but generally, I think it was pasted in a good way. Since it is firmly attached, it is unlikely to be dropped while driving.
The price seems high for Size, but I am satisfied with the results as expected.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Pricey but convenient for beginners
I think it is very convenient for amateurs to connect Motorcycle wires such as Blinker or Tail lamp. First, strip the cord, twist the wire that appears, insert it into the hole in the plastic part of this Connector, and snap it with pliers or something, and you have One Side. Do the same for the other side. The finished products are made of Male and Female, so you can connect them properly by plugging them into each other. It is an excellent product. However, if it is difficult to connect the wires, it is of course useful, but if you have a spacious place and have some room in length, I think it is best to put a solder on it.
The price is high and the cosmetics are not so good. But I think it's useful if you're in a hurry, a very beginner, or in a small space.
View detail
Frosted Material with high texture
I used this product to wiring up my Ninja250SL's sub-computer and USB. Honestly, you can use Curing Tape instead of this product, but this product is pre-cut, so it is easy to work with, and it looks overwhelmingly good, so it is a Recommendation! View detail