Reviews
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Fits: Others Wire clutchCompetition model, SUZUKI RMX450, SUZUKI RM-Z, SUZUKI RM, KAWASAKI KLX450R, KAWASAKI KX-F, KAWASAKI KX, YAMAHA WR-F, YAMAHA YZ-F, YAMAHA YZ, HONDA CRF-X, HONDA CRF, HONDA CR
Definitely lighter.
I had been using OEM Clutch for a long time, but it was too heavy and tiring, so I replaced it with this one.
To install, remove all the originally attached clutch lever and holder, leaving only the wires in place, and then install.
The dust cover is screwed on, so it must be disassembled and assembled before installation.
Also, the Clamp portion is rotated so that it is less likely to break than a regular Lever or OEM.
The Nut that adjusts the distance of the Lever is also hexagonal, a spec. that can be firmly fixed in place.
I prefer to set it quite far away, but it feels quite light when I pull the lever, I don't know if it's because of the Ratio or some other secret, but I think you can feel it the moment you hold it.
View detail
Firmly.
I could not tell how light the Clutch was, but the build quality was solid, as if it were an OEM product.
Durability, that is the most decisive factor.
View detail
Great grip comfort
The OEM Lever for the SV650 is a good or bad bike Level, but this Lever not only looks cool, but I was surprised at the high quality when I held it for the first time after installation!
Installation is easy and takes less than 30 minutes if you have experience with grease up and lubrication of Lever!
View detail
No different than OEMs
Purchased due to leaking oil line. I am glad that the quality is the same as OEM and the price is lower. I will buy again when it breaks. View detail
Fits: KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400R (-2013), KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA650R, KAWASAKI VERSYS 650
For NINJA400R
Installed on NINJA400R.
Since it is an important safety part, we asked Motorcycle shop to install it.
The feel of operation, texture, etc. was perfect without any complaints.
If you are not confident about installing it yourself, ask a professional contractor to do so.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Fits: SUZUKI GSX-R1100, SUZUKI GSX-R750, HONDA CB1000 SF, HONDA CB400SF, HONDA X4, HONDA CBR1100XX SUPERBLACKBIRD [Super Blackbird]., HONDA CBR900RR FIRE BLADE [Fireblade]., YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA XJR400, YAMAHA FJ1200, YAMAHA FJ1100, YAMAHA XS1100, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX250, SUZUKI GS1000, SUZUKI GS750, SUZUKI GSX1100, SUZUKI GSX750
Just cover it!
Funnel is bad for the engine and does not pass vehicle inspections. The RAMAIRSystem is a simple system that can be installed on the engine, and it is easier to remove than the Power Filter, so if you want to change to a funnel, you can easily remove it. View detail
Fits: HONDA XL250S L250S, HONDA NY50 All models, HONDA CROSSCUB110 JA10, HONDA All models of GIORNO CREA AF54, HONDA SUPER CUB 110 JA10, HONDA SUPER CUB 110 PRO JA10, HONDA SUPER CUB series Engine cars (50-100cc), HONDA SUPER CUB series Engine car FI, HONDA Spacy50 All models, HONDA DREAM50 AC15, HONDA Spacy80 All models, HONDA VARIE All models, HONDA MONKEY series Engine cars (50-100cc), HONDA MONKEY series Engine car FI
Very common EXGaskett
CROSSCUB110 (JA45) Used to replace the Exhaust System of
I think Gasket is the same for all Manufacturers.
No exhaust leak etc.
It was cheaper than OEM Parts.
View detail
Fits: SUZUKI GSR400, SUZUKI GSR600, SUZUKI GSR750
The texture is very good.
As expected from Made in Japan, the texture and finish are very beautiful.
Easy to operate as both lever and position can be changed.
View detail
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Fits: KAWASAKI ZXR250, KAWASAKI KLX125, KAWASAKI D Tracker 125, KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ELIMINATOR 250V, KAWASAKI ZXR250R
KLX125
KLX125
DrumstickDrumstick fits!
View detail
Shorter levers
I still wonder till today why so many bike companies use the ugly, cheap looking levers in one colour only. Or no colour to be precise. Fortunately there are plenty of levers to choose from. I chose these shorter with adjustable position on both sides. They look great, the instalation was easish :) Brake is easy, clutch is a little tricky, but that applies fro any clutch where you need to fit the knob on the wire inside the lever. But anyone can do it with a little bit of patience. View detail
Fits: HUSQVARNA TC 125, HUSQVARNA TC 250, HUSQVARNA TE125, KTM EXC, KTM EXC-F, KTM SX, KTM SX-F
Great replacement clutch lever
Best lever on the market,Buy one of these levers,Looks great and functions flawless. you will remember my words when you drop your bike and race because of a broken OEM lever.Durable levers, bike cartwheeled 4-5 times and the levers only had minor scuffs. View detail
It's shit.
I purchased it because of the mounting diameter Φ54, but the actual size Φwas only 45.
I couldn't get a direct fit on my SR400 CVcarburetor. It sucks. I tried to force it on and it deformed and I can't return it. It is a real piece of shit.
View detail
The texture and feel are both good.
[How is it used?
Because the OEMLever of the GSX-S 125 is not adjustable, and also to Upgrade its appearance.
We compared it to Endurance's Lever, but this one seemed to be more to our liking in terms of lever shape, length, etc., so we went with this one.
Was the one you received as per Image?
The texture is as good as the picture shown.
Was the installation difficult?
No problem.
How was your experience with it?
The adjustable type is easier to adjust to the position of your choice, and it also feels better when you run.
[Included Parts:were they on?
I think it came with a ManufacturerLogo sticker.
[Was there anything that disappointed you?
Nothing in particular. I dare say that the Retractable Lever was so loose that it moved immediately after arrival that I had to retighten the nut to prevent it from moving.
Blue Anodized is a little lighter than U-KANAYA's Blue, etc. I think it fits GSX-S125's Birdton Blue. (The Normal Holder has a large amount of play, so it may rattle a little, but I think that can't be helped. If you are worried about the rattling, it would be better to replace the MASTERBODY with Landor or brembo.
View detail
Japanese Vehicle Inspection Correspondence
Before the inspection of SR400, I went to the tester place off site to check the light intensity. I had to go back and forth to Tester two years ago, but they did it without any extra charge, I switched to the new Stanley Hyper Halogen LightValve, which I brought with me again. It is just 150mm away from the specified light level, but it is OK.... Hyper Halogen Light is a high efficiency valve and can be brighter with the same power consumption as the standard valve, but it seems to have a shorter life. View detail
It is easy to install.!
OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good.
View detail
Fits: HONDA CB1300SF, HONDA CB1300SUPER BOLDOR
It looks cool and is even easier to operate!
Clutch, Brake and Quantity:I appreciate the price for the Set.
Installation is easy and quick.
The texture is good and it is easy to dress-up.
The distance to Lever is shorter than OEM, making it easier to grip and operate.
View detail