Reviews
![Repair Lever [VRC/VRE Series]](https://img.webike-cdn.net/catalogue/images/70124/VRC_POWER_TS.jpg)
Replace with Round
It is a replacement for the old Labor. I think the round shape reduces the attack on the fingers when gripping. View detail
![Lever for Repair [for Wire Clutch Holder]](https://img.webike-cdn.net/catalogue/images/70124/GALE_WIRE_TS.jpg)
Replace with Round
This is a replacement from the old TypeLever. View detail
Looks good and functional
İ dont know.i think so manufacturing tolerances are no good . In order to get it to spin in a crash or tip-over it needs to be loose so that it spins but then it makes the perch loose and that jiggles and wiggles and makes the whole perch move and subjects that to even more crash damage. Plus it moves when landing from jumps.Despite this, it's a great looking part at a good price, I'll give it another shot. View detail
It seems to work without Wire's Adjuster.
When Adjuster is used, the wire sticks out and cannot be used. Therefore, it is not necessary to prepare it separately. View detail
Ultra Small Type
It is too small, so choose where to use it. View detail
It's not bad.
The lever position adjustment is a mechanism where the screw comes out and hits the base, so it is not possible to adjust without a tool. I would like to have a dial type adjustment like the brake lever.
The shape of the Lever is common, but I personally would have liked the cross section to be more rounded for easier gripping.
View detail
I'm just pimping...
[How is it used? Town ride
Was the one you received as per Image? It was a little different.
Was the installation difficult? Simply replace the Connector and you're done!
How was your experience with it? The light went from a light bulb color to a white light color like a White color fluorescent lamp, and the light was confirmed to be lit well even in daylight.
[Included Parts:were they on? Two Tie Wraps in Black for outdoor use
[Was there anything that disappointed you? Quantity of claws to fit into the insertion slots.:Pair (for Left and Right) Wiring is oriented in the same direction, so depending on the direction, the wiring is short and may interfere with the cowl, so care must be taken when routing the wiring.
Replacement of ▼Lamp requires removal of the exterior of the car body, No.2 long and short +Driver, M10φ? SocketLunch.
View detail
Fits: HONDA VTR1000FVTR1000F FIRESTORM, HONDA VFR800, HONDA VFR800XCROSSRUNNER 125, HONDA VFR800F
Lever of Leaning Type
Unlike the Touring type, it has a hard feel to the touch due to its angularity. View detail
Fits: BMW Monolever R 100 RT from 09/85 on, BMW Monolever R 80 from 09/85 on, BMW Monolever R 100 RS from 09/85 on, BMW Monolever R 65 from 09/85 on, BMW R 100R, BMW R 100R Mystic, BMW R 80, BMW R 80 from 09/89 on, BMW R 100GS from 09/89 on
Thanks for handling it.
[How is it used?
chirping of a small bird (Dragging at the limit of use?) Exchange due to
How was your experience with it?
no problem
Braque squeaks are cleaned and eliminated upon visual inspection of the part mold prior to ordering.
Brake Shoe had room to spare before replacement, but was replaced due to age-related deterioration.
How did it compare to other products?
Other manufacturers that I searched on the Internet said that it works, but there is a lot of dust.
[Points to note]
The Brake Shoe of R100GS is completely different between the First Model Type and the Second Type Model, so it cannot be used. (We are Second Type Model of 91 MODEL)
Brake Shoe only, Spring and its protective rubber are not included.
The finish is just a little rougher than the OEM Product that was removed.
There was a slight BALI or roughness in the areas where Spring might touch, the hole it passes through, or where it might touch Cam, so I scraped and polished it with File, just to ease my mind.
[Others]
It is nice to know that OEM Products through Dealers have more inventory than expected, even after decades of Motorcycle discontinuation, but the prices are several times higher than they used to be, perhaps including administrative costs.
Giebenrock is still selling some of 2Valve's R100 Parts! (See Germany's website) I have never imported from a private company before. I have never imported from an individual before, so I purchased from WeBig.
*I rated it in the middle because it has only been installed for a short time.
View detail
Fits: BMW Monolever R 100 RT from 09/85 on, BMW Monolever R 80 from 09/85 on, BMW Monolever R 100 RS from 09/85 on, BMW Monolever R 65 from 09/85 on, BMW R 100R, BMW R 100R Mystic, BMW R 80, BMW R 80 from 09/89 on, BMW R 100GS from 09/89 on
Glad you are selling it.
OEM Product via Dealer is nice to have in stock even decades after Motorcycle has been out of production, but the price is several times higher, perhaps including administrative costs.
I thought that Giebenrock, which still sells some parts for the 2V R100, would be more reliable than other manufacturers that I could find on the Internet, so I bought from Webig, since I have never imported from Japan.
I rated it in the middle because it has only been installed for a short time.
*The number of Parts we deal with has been reduced a lot on the Giebenrock Home page.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ125, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250F, YAMAHA YZ250F, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ450F, YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ250FX, YAMAHA YZ450FX, YAMAHA YZ450FX, YAMAHA WR250F, YAMAHA WR250F
Rear works just fine.
I bought this for beta RR2T 250 MY2020 which I always use for forest road touring.
Rear brake is used.
ZETA has good Control instead of rapid Brake not working.
Therefore, we have installed ZETA's Pad to meet the Rear brake, which is hard to Control when it is too effective.
Especially on sharp downhills, too much effect will inevitably lock the rear brake, so a pad like ZETA's is just right.
View detail
Fits: その他 Off Road Caliper P2 28 (Code XQ21361), その他 Off Road Caliper P2 24 (Code 122A99021), その他 VR250 Super, Otard, その他 VR250 Enduro, その他 Scrambler, その他 Granpasso, その他 Granpasso, その他 Granpasso, その他 Granferro, その他 GT, その他 Enduro 610, その他 Enduro 250, その他 ED250, その他 E 570 Enduro, その他 CD610., その他 C 570 MX, その他 C 500 MX, その他 C 450 MX, その他 ATK700 Intimidator, その他 ATK620 Intimidator
It works better than ZETA's Pad!
I installed it on my gasgas EC250 which I always use for forest road touring.
I used to use ZETA Brake Pads, but I had a symptom that the brake did not work too well on descents, and my arms would go up when I rode for a long time or during high-load Situations such as Race.
So I started working on improving Brake and the first thing I bought was Brake Pads.
It was not a drastic improvement, but it works better than ZETA's Pad, and it can stop with a little less Speed in Downhill, etc. However, I still have the impression that a little more StopPingPower would be nice.
View detail
Fits: HONDA BROS650, HONDA BROS400, HONDA NIGHTHAWK750, HONDA STEED600, HONDA STEED400 VSE, HONDA STEED400, HONDA STEED400, HONDA STEED400, HONDA Shadow slasher750, HONDA Shadow slasher400, HONDA Shadow classical400, HONDA SHADOW750, HONDA SHADOW750, HONDA SHADOW750, HONDA SHADOW400, HONDA SHADOW400, HONDA SHADOW400, HONDA XL400VTRANSALP, HONDA XL250, HONDA X4
Cheaper than OEM
I bought this one because it was cheaper than OEM.
There are no exhaust leaks and no problems.
View detail
I think the texture is good.
[How is it used?
I replaced it and ran about 150 km.
The shape of Lever is slightly different from NORMAL, but I soon got used to it.
Was the one you received as per Image?
Almost as Image.
Clutch lever is a little cheap in the Plastic part.
Was the installation difficult?
I am a beginner and it was very easy because there was a video of the exchange on Youtube.
I think anyone with 8mm and 10mm Wrench can do it.
How was your experience with it?
It looks good because we matched the color to the Fork and Wheel!
[Included Parts:were they on?
Grease is not included, so if you don't have it, you should buy it.
[Was there anything that disappointed you?
Plastic part of Clutch is cheap.
View detail
Think in terms of replacement frequency, not Power
I don't think there is anyone who can perceive the increase in inhalation efficiency by 0.5ps at Peak with SEROW in the product description.
I'm more of a wash and reuse kind of guy, but it's a lot more work than I thought it would be.
According to the official procedure, wash with Cleaner→ wash with mild detergent→ dry for a day→ apply Oil→ wait 6 hours and when Oil settles, you can drive.
Almost two days if you follow it exactly? If I wash on Saturday morning, I won't make it in time for Touring on Sunday.
If you're the kind of person who changes filters once or twice a year, OEM replacement would be better.
I guess it's for people who want to go as fast as possible in an hour-long Race to change filters in a month, which is often run in Course.
View detail
![[for Repair] Silencer Gasket](https://img.webike-cdn.net/catalogue/images/66105/20170107_f46cb8_TS.jpg)
Silencer gasket
I used it when I installed T2RACING's Silencer on Hulk's Chamber, and although the Silencer itself was confirmed to fit, the three M6 mounting pitches were different and the hole on the Flange side needed to be widened by about 0.5mm.
Gasket also naturally has a different Pitch and requires a wider hole.
Some modification may be necessary when using for chambers other than T2RACING.
It functions fine and has no exhaust leaks.
View detail
Fits: HONDA CRF250M, HONDA PCXe:HEV, HONDA PCX, HONDA PCX160, HONDA PCX150ABS, HONDA PCX HYBRID, HONDA CRF250L, HONDA CRF250 RALLY, HONDA CRF250 RALLY LD, HONDA ADV150, HONDA ADV150, HONDA ADV160, HONDA CRF250 RALLY, HONDA CRF250 RALLY LD, HONDA CRF250L, HONDA CRF250M, HONDA PCX eHEV, HONDA PCX HYBRID, HONDA PCX, HONDA PCX150
Stiff
It is somewhat stiff, and I am concerned about the feeling of the Pad being scraped during Brake.
The Red Pad went away very quickly, so I will use it with high hopes for durability.
View detail
Fits: HONDA CB1300SBSP, HONDA CB1300SB, HONDA CB1100RS, HONDA CB1100EX, HONDA CB1100, HONDA CB1300ST, HONDA CB1300 SFSP, HONDA CB1300 SF
After 20,000 km
Purchased due to idling failure after full power. I am looking forward to the next Touring, but have not driven it yet. View detail
For XSR155 is not compatible with XSR125
Lever for XSR155 cannot be used for XSR125.
I bought it thinking that it would be diverted, but it didn't work.
The shape is different
The quality of the product is good, so I'll wait for the confirmation of XSR125 application before I buy it.
View detail
Fits: HONDA DJ-1-RR, HONDA G', HONDA CABINA 50, HONDA CROSS CUB 50, HONDA JULIO, HONDA JOKER Helmet 50, HONDA Giorno, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50 Standard, HONDA SUPER CUB 50 DELUXE, HONDA SUPER CUB 50 Super custom, HONDA SUPER CUB 50 PRO, HONDA SUPER CUB 50 PRO, HONDA SUPER DIO, HONDA SUPER DIO -SR, HONDA SUPER DIO -ZX, HONDA TACT, HONDA TACTSTAND-UP, HONDA TACT
1pc. is Smaller
The first one was a little smaller than the second one, so the Quantity:Set and it's falling down.
The other one was a good Just fit.
View detail