Reviews
Screw goes missing.
It is used with Pillion Bar.
Quality as a Holder is perfect!
It is well made and highly satisfactory.
However, the screws for adjusting the Large size may be prone to falling off.
If you don't squeeze it properly and drive with it loose, it will fall off before you know it.
Once it is lost, it is even more likely to fall off with other nut, etc. Therefore, it may be necessary to first apply Screw lock to the tip of the Bolt to prevent it from falling off.
View detail
Fits: BMW S1000RR, KAWASAKI NINJA H2SX , KAWASAKI NINJA H2SX SE, KAWASAKI NINJA H2SX SE+
Mount bar with a large range of motion
[How is it used?
USB charging, for mobile Holder installation
Was the one you received as per Image?
Exactly the same as the photo shown
Was the installation difficult?
The installation itself is not difficult, assuming that there is a hole in the CenterPost of the Top Bridge.
Also note the hole diameter.
By tightening the screw, the Ring expands in the CenterPost and is fixed in place.
It tries to move somewhat even when it is fully tightened. This is unfortunate. However, it is a playful part like BacCrash.
Screw Lock (medium strength) must be used for the screw part.
How was your experience with it?
Very stable and very easy to use due to the wide range of motion.
No vibration, etc. is produced.
Pipe thickness is also common, making it highly Universal.
It depends on what you are going to install, if you are going to install a portable Holder, USB power supply,
I think 100mm is too short.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
CenterPost holes are not well fixed.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Assist the unique Handlebar shape.
The unique handlebar shape made it impossible to install parts with Handle near the handle, but these parts saved the day.
I have been using it for 3 years already and have no problems, so I bought another one the other side.
View detail
There was no problem
[How is it used?
For Holder fixing
Was the one you received as per Image?
Street Image
Was the installation difficult?
It was easy.
How was your experience with it?
It was good
[Included Parts:were they on?
Mounting with Bolt
[Was there anything that disappointed you?
nothing special
View detail
Drink holder
I am very satisfied with the way it is made.
It is very good because it can be easily adjusted according to the Drink Size.
View detail
I think about it a lot.
[How is it used?
The shape of the handlebar makes it impossible to attach a camera or cell phone holder, but this product makes it possible to attach a camera or cell phone holder.
Was the one you received as per Image?
I bought one about a year ago and was happy with it, so I bought it again.:Pair (for Left and Right) Mounting on
How was your experience with it?
Purchased this in addition to a previous purchase that I was happy with.
[Points to note]
The photo appears to be made of Gold, but in reality it is Material.:I was worried at first because it is Plastic, but I used it without any problem.
How did it compare to other products?
This product only
View detail
A little expensive, but satisfactory
[How is it used?
Purchased Quadlock Mount to work with Scooter.
Mount, QuadlockMount, and iPhone XS Max on my commute to work.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
It is very easy to use, just put it on the Mirror mount.
How was your experience with it?
Mount is thick enough and strong enough.
Satisfied with the freedom to change angles.
The phone doesn't shake at all.
Black Anodized has been in use for 3 months and has not faded (maybe with lighter colors?).
[Included Parts:were they on?
All parts for installation are included.
[Was there anything that disappointed you?
None in particular
View detail
It is easy to install.
As the Title says, It is easy to install.
Simply insert into the stem shaft and tighten.
The parts themselves are very easy to assemble.
However, there are likely to be individual differences.
Even if the hex on the mount bar side is tightened quite a bit, it rattles a little.
Easy to install and assemble.
Recommended
View detail
Speedra Drink holder
Installation was easy and I was satisfied with both the design and the quality. View detail
Adjustments.
The mounting height can be changed, allowing for adjustment to a user-friendly position.
The width can be easily adjusted with the screw on the bottom to fit plastic bottles and water bottles, so there is no wobble when running.
Aluminum and luxury.
View detail
Easy to install
It's easy to install, just remove the Stem Cover and install. I'll have to wait and see how it holds up. The bar is a little low, so you should be careful when you install the Smartphone Holder because it might hit the Shield when it is fully locked. View detail
Easy installation
It is easy to install and strong enough.
The color is a little lighter than Kawasaki green, but
OK because it's cosy!
View detail
For Navigation installation
I bought this for Navigation installation. I used PartsRemover for Plastic model. View detail
Fits: KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI GTR1400
NINJA650
I was able to install it on my NINJA650. View detail
Fits: KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI GTR1400
Navigation installation
I bought this to install a used GORILLANavigation.
It is long enough and does not interfere with the Meter's visibility.
Best
View detail
Fits: BMW S1000RR, KAWASAKI NINJA H2SX , KAWASAKI NINJA H2SX SE, KAWASAKI NINJA H2SX SE+
unrestricted
I could position the SMART phone to my liking. View detail
Fits: BMW S1000RR, KAWASAKI NINJA H2SX , KAWASAKI NINJA H2SX SE, KAWASAKI NINJA H2SX SE+
unrestricted
Setting can be decided in all directions View detail
Mounted on PCX160
I installed it on my PCX160.
I bought this because I was missing One Side with the Handlebar Brace installed and the Smartphone Holder.
The texture is pearl and I like the simple design.
You can adjust the width of the bottle with the knob on the bottom side, so you can make it fit your plastic bottle just right.
I recommend it because it is very reasonably priced.
View detail
It's not bad!
No problems and useful.
If I had to make a complaint, it's a matter of personal preference, but the paint job is a bit cheap.
It's a shame that the pictures of the product didn't show it clearly.
I would have given it a 5 if it had a texture like the Aluminum Cut-Out.
View detail
It wasn't a good fit for my application
The texture is good
The 500ml plastic bottle interferes slightly with the Max width
When I say snug, I mean it's snug, so you won't have to worry about it falling out However, that's why it won't fit if you put the Cover on to keep it cold
I wanted to use a cold storage Cover, so I replaced it with a 10+ year old Laphro Holder and It's a shame It is a pity that the adjustment range should be a little larger
View detail