Reviews
This is the second time I've replaced my TMX30 Power jetHose!
This is the TMX30 sold by Mikuni.
This is the second time I've replaced the Hose on my Power jet.
The replacement Cycle might be a little early because it deteriorates by the ultraviolet rays outside.
View detail
Replaced the Jet needle on my TMX30 sold by Mihara!
This is TMX30 which was sold by Mihara.
I replaced it because it was getting old and the Jet needle was a consumable.
View detail
My Mihara TMX30 is getting old, so Needle Jet replacement!
TMX30 sold by Mihara is getting old.
I also replaced the inside of the Needle Jet tube as it wears out.
View detail
When the TMX30 Overhaul's, we swap together!
The TMX30 sold by Mikuni has become old, so I decided to overhaul it.
The entire Needle Valve is also replaced.
Now there's no Trouble!
View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
Same number as the TMX30 Idle Screw Packing!
It is for TMR but the part number is the same as TMX30 Idle Screw.
If you install it, it's the same and it's Large sturdy.
Packing itself is Material:It's Plastic and I replaced it before it deteriorated.
View detail
Replacement of Float chamber packing for 20 years old Mihara TMX30
I replaced the Packing in the Float chamber as my Mikuni TMX30 is over 20 years old.
Apply Silicon grease to make it stick better and then put packing.
I'd replace it before it leaks!
View detail
MikuniLong Idle Screw
I installed it on my TMRMJNCarburetor.
Without it, you can't adjust the RPM delicately.
View detail
Fits: その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35
OEM
The MikuniOEM Product is of high quality and can be used with confidence. View detail
Thank you for the OEM negative pressure carburetor setting parts available
DR250S (SJ44) Used for 。 Become an OEM Oversize.
It was in stock when I ordered it, so it arrived quickly.
It is very nice to be able to buy the setting parts for the negative pressure carburetor immediately.
I had changed the intake and exhaust and the PS adjustment was all over the place, so I went up 1 size.
It is not difficult to install if you are able to Rose the carburetor because you only need to replace the one you have now.
I'm going to have to adjust the PS, but I think the replacement will do the trick.
View detail
In FZr1000 3GM, it is here.
As the title says, in FZr1000 3GM Series, it is here.
* OEM Product No. 4G0-14142-40
Here by mistake URL → https://www.webike.net/sd/1082359/is installed, you will be lacking Gas without knowing it.
Of course, it also emits a tremendous amount of Black smoke.
Did you buy the wrong one when Carburetor overhauled?
The person who becomes bad condition by the cause of this, especially like Across250 which Mr. Ma of a certain Mr. Ma of Garage was riding before, will become considerably bad condition.
* Video shows FZr1000 3GM5 with good low speed range
View detail
OEM Parts name:Pilot air jet?
The OEM Parts number on the FZr1000 3GM5 is 830-14231-23 #115.
This is the product.
For example, it may be the same with the N211-100, but there is no streak Mark on the outer edge of the Jet.
If OEM Parts is out of stock, you can buy this one.
* For removal, the thinnest of the reverse taps will do.
* Video shows Carburetor Tuning
View detail
Used for TE250
I ride a 2017 HUSQVARNATE 250, which is a 2Stroke off-road motorcycle.
I bought it in good condition from Motorcycle, which I bought from a private seller about 6 months ago.
I use it for forest road touring and intense HardEnduro type play.
It is so much easier to handle and more powerful than my previous motorcycle and makes hill climbing so much easier.
The Mild handling at low speed and the high speed range is the best motorcycle, but the sluggishness at mid speed is becoming very annoying.
It is said that the reputation is bad when it examines it variously, and it is Mikuni by the exhaust Gas measure only in this model year, and it seems to be improved overwhelmingly when it makes it to KEIHIN.
However, because I don't have enough gold to buy a carburetor, I decided to adjust the part I was worried about by jetting. The symptom was that it was thick and lean, so I changed to a thinner Jet and it was a great improvement. I'd like to boil it down a bit more and hopefully ride with the Mikuni as it's a budget issue.
View detail
Setting of TE250
I ride a 2017 HUSQVARNATE 250, which is a 2Stroke off-road motorcycle.
I bought it in good condition from Motorcycle, which I bought from a private seller about 6 months ago.
I use it for forest road touring and intense HardEnduro type play.
It is so much easier to handle and more powerful than my previous motorcycle and makes hill climbing so much easier.
The Mild handling at low speed and the high speed range is the best motorcycle, but the sluggishness at mid speed is becoming very annoying.
It is said that the reputation is bad when it examines it variously, and it is Mikuni by the exhaust Gas measure only in this model year, and it seems to be improved overwhelmingly when it makes it to KEIHIN.
However, because I don't have enough gold to buy a carburetor, I decided to adjust the part I was worried about by jetting. The symptom was that it was thick and lean, so I changed to a thinner Jet and it was a great improvement. I'd like to boil it down a bit more and hopefully ride with the Mikuni as it's a budget issue.
View detail
Fits: Others TMR Carburetor for large body(Φ36-Φ41), Others For TDMR Carburetor Large body (Φ36-Φ41)
Essential parts for setting TDMR40
An essential part of the TDMR40 settting.
The ease of setting out is Large, and the dissatisfaction is the place where the difference of one step of Clip is Large.
I use a plastic Washer to fine-tune about half of the Clip.
Well, other than that, I'm satisfied, so it's OK.
View detail
Fits: YAMAHA RZ250, YAMAHA RZ350, YAMAHA RZ250, YAMAHA RZ350
I wish it was a little cheaper.
A brief Instruction Manual for TMXcarburetor was included.
Because it is a special product, there is no problem in installation. However, TMX30 has a strong return spring, so it's hard to insert it alone without the help of a cat.
The Cable on the Throttle side looks thin and stiff and seems to easily fray if you push it too hard.
If only the price would be a little lower since there is no choice.
View detail
Fits: YAMAHA RZ250, YAMAHA RZ350, YAMAHA RZ250, YAMAHA RZ350
Reliable Dedicated Products
The price is slightly higher than the rebuilt and other products, but I bought a dedicated product for peace of mind, as there is no clear information on alternatives that can be used as is.
A simple Instruction ManualCopy of the TMX30carburetor is kindly enclosed.
The spring is so long and strong that it is difficult to install it by myself, I had to ask the help of an assistant to hold the spring, but other than that I could install it with no problem.
View detail
Used for free rides!
Used on my KTM and Freeride that I ride in the woods touring and off-road. With this Screw installed, it is very convenient to adjust the Idling right away. View detail
I bought it because I wanted to set the oil level to the default value.
The original one that came with it was bent, so I bought it as a Repair.
Since it is Mikuni OEM, it was easily replaced without any problem. The quality is no problem at all.
View detail
Essential for Setting!
I bought it as a YAMAHA X1R model.
Since Idling is not stable, Idling stabilized when I made it thicker by raising the number of positions.
You can choose your size.
If you want to keep it in Stock, you should put it in a Case because you tend to lose it.
This is an essential part of the Carburetor setting.
View detail
Parts for carburetor settings
I used it in the setting of a HUSQVARNA TE250.
I have no knowledge of carburetor so I bought it based on what I heard from my colleagues.
For Setting, you have to buy a few different Jets.
And I felt that Setting required a lot of knowledge.
View detail