Reviews
Lay the square section down first then the round section...
Because the protective film is cut almost exactly the same size as the face of the Opmid multimeter, the film edges will not lay flat if it's not set down perfectly. Opmid should have pre-installed these films on the multimeter at the factory, hence 4 stars. Onces you get it perfectly centered, the film is excellent. The matte, non reflective film I chose works great in sunny condtions. Great that you get 2 films in the pack, backup or just in case... I'd recommend it, a good way to keep the face from scratching and less glare from the sun. Just take your time installing and use painters tape to remove dust from the 2 surfaces before you lay it down and push bubbles out. View detail
All in One Instrument Gauge for the Monkey
About quality and texture: I am happy with the quality of the multimeter from Opmid. The housing is made from all plastic with a gloss finished screen. The display is all digital just like the OEM Honda meter. About the feeling of use: This instrument gauge has every thing you could possibly want to display on your Monkey and I much prefer the look of the digital tachometer added to the displayed. Products to buy together: A SP Takegawa oil temperature guage and drain bolt would also be desirable to purchase alongside the multimeter so you can display the engine oil temperature from not just the OEM Honda sensor on the cylinder but also from the crankcase area. Difficulty of installation: The process to install takes about 2 hours to install and setup. Remove the headlight and OEM Honda meter then position the temperature wire and tachometer wire. Install the meter bracket followed by the meter and connect up all the wiring to the meter. Now follow the instructions on how to setup the meter. A little difficult to do. Cost performance and comparison with other products: Good costing as you are getting an all in one instrument gauge that is able to display everything you could want on the Monkey but the price is high as compared to the previous tachometer I was using from SP Takegawa that did a fantastic job but is missing a few features. About shipping and packaging: Sea frieght is my preferred method of shipping due to the lower cost and it is fantastic that it has returned as an option once again so I can put my money toward parts and not high shipping costs. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: Like I have already said this is an all in one instrument gauge but if you have unlimited funds then you will want to purchase the super multi TFT meter from SP Takegawa that has a coloured digital display. View detail
Satisfied because I wanted a Taco Meter and a clock.
[How is it used?
Used for traveling home every weekend on my own and for Touring. Purchased because I wanted a Taco Meter and a clock.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
Voltage extraction was difficult to perform according to the Instruction Manual, so the Right Side Cover was removed.
How was your experience with it?
The Tacho Meter is very useful when shifting.
Easy to set up.
[Included Parts:were they on?
The camera came with everything, but I purchased a glossy protective film separately.
[Was there anything that disappointed you?
None in particular
View detail
No problems
I bought glossy Type based on other impressions.
The display is easy to read.
If the tape is not attached properly, it can be reattached.
View detail
Best value meter, including oil temp
Great value when you consider this also has oil tempature readout using the stock sensor. Lots of configuration options and great style for CT125 View detail
Short warranty
About six months after installation, the Body began to turn on and off, and finally stopped working after less than a year.
I checked the warranty period and it is only 6 months. Is it a spec. that will break when the warranty expires?
I bought the same product and installed it, but I don't know what will happen.
View detail
So so
As long as you have a USB power supply, it only takes a minute or two to install! The warmth is also quite good as it gets warm in less than 30 seconds. The only drawback is that the grips get thicker as a result… View detail
Operation check complete
Quantity:The Instruction Manual says to adjust the length of the 2pc cord, but the Tie Wrap is too tight to adjust. The Tie Wrap was so tight that it was embedded in the cord's clothing. I had to remove the Tie Wrap because it was too tight and it might become a resistance.
The grip will probably get used to it quickly. The warmth is also good.
View detail
Mounted on CYGNUSX5 type!
[How is it used?
It was installed on the last MODEL 5 of CYGNUSX. The model that fits is not listed for the model 5 CYGNUS, but...
The webike article said it could be installed on a 5-inch model, so I had no problem at all.
CYGNUS is mainly used for commuting, but I am still concerned about oil temperature since it is an air-cooled Engine...
It is also recommended that an Oil Temperature Meter be attached to the system so that it is easy to see how far the system should be warmed up.
Even in summer, it goes about 120°C when waiting at a traffic light after driving on the main road at full throttle.
If the machine is equipped with an oil temperature meter, we can watch the temperature and try to operate the machine in a gentle manner.
Was the one you received as per Image?
It was more Compact than I expected! But visibility is very good.
Blue letters are also very good, and daytime visibility is very good.
Was the installation difficult?
The tricky part is to remove the cowl around the front. However, once the exterior is removed, the rest is easy.
Coupler is all ponting, so there is no need for any troublesome work to create wiring.
As described in the webike article, it is mounted using Mirror and a Bracket that is mounted by coaxial mounting.
I guess you could stick it on top of the Switch box, but I used Bracket because I didn't want it to look bad and I didn't want to stick it directly on the BOTY.
How was your experience with it?
The first thing to do is to display the voltage for a few seconds when the key is turned on, which is useful to know if the battery is healthy or not.
Especially since the 5-type CYGNUS does not have a KICK, it will be finished when the Battery goes up.
After that, oil temperature is displayed, very easy to read.
[Included Parts:were they on?
It is as shown in the picture. No other.
[Was there anything that disappointed you?
Not at all! Very good product!
View detail
Is good
The Grip is a little thicker, but it was not thick enough to bother me.
Grip heater with Grip replacement Type is good for winter, but in my case, I want to use the basic Grip that I like, so the easy removal is very convenient.
View detail
Fits: HONDA GROM, HONDA MONKEY125
Essential ITEMS when replacing GEAR!
Made by OPMID
Dr.SPEED Vehicle Speed Signal Correction Unit installed.
Remove Seat and Left Side Cover and look for Coupler to connect 6V MONKEY/GORILLA Main Harness.
Check the Wiring color in the Wiring diagram and interrupt the Coupler of the Correction Unit, then neatly bundle and store the connected Wiring.
Controller is installed next to the Battery for installation.
is complete
Then, while looking at the Instruction Manual, turn the rear wheel to test the connection and enter the correction value.
BUT!!! Here's the problem...
I can't see... Indicator LED is too dark to read.
Hm!!!
I had to redo the input again and again, hiding it with my hand...
This input work took longer than the installation work.
I would like to have a brighter LED at any price.
Because you can't read them outdoors during the day!
But now that the Speedometer is accurate, it's safe to say.
I'll take the CUB for a ride next time to check the numbers.
View detail
Parenthesis is good, but it's broken.
It looks good and makes the MONKEY look one size larger.
After a year and a half, it suddenly went into high flasher status, even after re-configuring the settings...
Removed. Tarnished.
View detail
Super easy installation
I bought winter Gloves but after an hour my fingertips are dead.
I was considering Grip heater and found it.
It's super easy to install and remove.
It is used in conjunction with Knuckle Visor.
This will allow them to survive the winter.
View detail
Fits: YAMAHA Tricity 125, YAMAHA Tricity155, YAMAHA Tricity155
Wiring processing:unnecessary?
Interrupt Connector for Water Temperature Sensor does not fit.
There was no mounting Seal included.
The product itself was of interest to me and this was the second time I purchased it (MAJESTYS last time), but I was disappointed.
View detail
at your ease
Installation was easy. However, since the grips were replaced, it was a bit more difficult since they are slightly thicker than the normal ones. The feeling of use is that it does not get very hot because the voltage seems to be a little insufficient since it is taken from KITACO's two USB ports. But I am satisfied because I could easily install it. The temperature does not drop that much because it is used in the Kansai region. If I were in a northern country, I would not be able to use it this way. View detail
Easy to put on and take off, but warm enough
I was thinking about a Grip heater because I really don't like cold hands in winter, and I was interested in this product because it is an easy spec. to wrap around the Grip with USB power supply. I read other reviews and thought it would be useful, so I bought it and installed it on my CT110 HUNTER CUB. In my case, the USB power supply of CT110 HUNTER CUB is 2Ampere and this Grip heater is more than 2.1Ampere, so I was worried because it is a little short. The way I wrap it around my hand, it hits my fingertips. Then I don't have Heater on my palm but I don't feel cold when my fingertips are warm. Also, it was more convenient that way because the distance to Brake lever didn't change. However, I use it on high because it is cold. I use it on high because it is cold. Medium or low is not good in temperatures below 10 degrees Celsius. I also use a hand guard to prevent direct exposure to the wind. I think it was a good decision to buy this product. View detail
ใช้งานได้ดีครับ สินคีามีคุณถาพ ปกป้องไมล์ได้ดีเลยครับ View detail
Two units share a pontoon griffin
[How is it used?
Shared by CT110 HUNTER CUB (CT125) and Motoguzzi V7?
Was the one you received as per Image?
The heating element and harnesses are well made and seem to be durable.
How was your experience with it?
Connect to Motorcycle USB Socket (made by DAYTONA), Cigar socketType USB Socket and Phone Charging Battery. "strength" Riding around the city in 3SeasonGloves in MODE. It's so-so warm.
I think it is warm enough for 8 to 10 degrees Celsius outside, but it may be better than nothing in the middle of winter (I have not experienced it).
Easy to attach and detach heating element grips (easy to switch between two units).
The instruction manual says to use Tie Wrap Fixing after installation, but I don't have a Gap, so I use it without Tie Wrap.
The heating element is positioned to warm the base of the finger to the belly of the finger.
(Grip tends not to grip, so the belly of the hand does not warm up)
It can be used with a smartphone charging battery, so a motorcycle without a USB socket should be OK.
I purchased a 3-stage temperature control with Switch, but in the wintertime. "strength" Since I think it will only be used in MODE, I was happy with this inexpensive Series product without the temperature control Switch!
[Points to note]
It is not waterproof specification, so please be careful in the rain.
I'll do a start-up inspection to make sure the heating element cord on the Throttle side doesn't get caught.
How did it compare to other products?
I was also a candidate for the other company's product, which is a type of heat-generating Seat that is fastened with a String, but I decided on this product because it is easy to detach and attach when two units share a Seat.
View detail
Costa is outstanding!
The CT110 HUNTER CUB is not equipped with a Tachometer, so we were looking for a retrofit Tachometer.
There was a Tachometer from Universal Product and a Digital meter from CT110 HUNTER CUBExclusive Design, but I chose the OpMid Multimeter for its features, price and looks.
Thanks to the easy-to-understand Instruction Manual, even an inexperienced person like me was able to install the Merit in about an hour and a half.
The Tachometer is taking its signal from the Ignition coil, so I believe it is an accurate indication.
The Shift indicator is calculated from the RPM and vehicle speed to determine the GEAR, so the display is delayed by one TEMPO13. However, other indicators such as Oil Temperature Meter, Clock, Oil Exchange Distance Setting, Blinker and Neutral are bright.
I would recommend this Meter to anyone who rides the CT110 HUNTER CUB.
View detail
For street riding
It's good for shopping and other small errands. View detail