Reviews
Fits: KAWASAKI Z1000 (water-cooled)
I bought it...
I finally got my hands on Wheel!
And in Marchesini!
At first I was thinking about GALE SPEED or OZ RACING.
Over the past year, Wheel has gone up in price considerably and Gale has lost its value for money.
OZ RACING has become more expensive than Marchesini
470,000 yen for standard Anodized Color, 550,000 yen for Paint
Too expensive.
Marchesini the King in his own value system, the nobleman OZ
I felt like a commoner GALE SPEED.
If they undercut that and the price exceeds Marchesini's, I'd choose Marchesini.
And GALE SPEED's Brand power is inevitably weak compared to other niManufacturers.
Add $140,000 to Gail's GP1S and you'll be promoted to Marchesini.
That Marchesini didn't like 7 Spokes at first and shunned it.
See, 360 degrees around the circle is not divisible by 7.
This means that somewhere out of the seven, there is a disproportionate etc.
It's kind of creepy, isn't it?
The price and design lightly erase such thoughts, a lack of conviction.
As a result, I chose Marchesini's M7RS over Gale and OZ.
Review from here
I knew it was lightweight, but when you actually ride it, it changes more than you can imagine.
The forging and thin Rim make the GYRO effect much weaker.
It feels like the head goes in and falls down without the action of bending it.
It's so light that I'm afraid it's going to fall over as it is.
To be honest, I've seen a lot of these reviews and sometimes I wondered how they could change like that.
I can feel the difference when I feel it. Even I, an insensitive person, can feel the difference so far, so I guess normal people can see the difference, can't they?
There's Merit, of course, but there's also the downside of the lighter weight and reduced GYRO effect.
First of all, straight line stability is reduced, if not to the point of dizzying.
I get the sense that there's something unsettling about it.
I wonder if it is noticeable when the speed exceeds 100 km/h.
Also, Small Gap is transmitted as vibration.
This is thought to be due to the fact that the lighter weight is not fully absorbed and transmitted.
Maybe once you get used to this area, you won't mind.
Also, I've seen a few reviews here and there that say it's often springy.
I think I can solve the Large one by setting up the suspension.
The place where the Wheel was installed has various know-hows and
I didn't have the feeling that I'd be hosed if they did the Setup for now.
It looks good, performs well, and you won't regret buying it.
I myself bought it 80% on looks, so it's unlikely to be effective.
I think it is very effective Large for people who drive fast and furious on mountain roads.
View detail
At least a necessity if you're going to run Circuit.
Circuit runners have generally pointed out the softness of the Rear, and I agree with them. I bought this product to solve this weak point because I can't change the direction of the rear end when I am turning and I spend a lot of time lying on the ground. I bought this product to solve the weak point of the RACING Link Plate. The initial entry of the car was changed from a squishy feeling to a gushy feeling, and there was no problem with the WindingLevel. The BFRC is fundamentally soft, so there is still a sense of over-movement. I will check if it will hold up or not at the next run. View detail
Fun to run.
I have ridden various motorcycles but this is the first time I have installed Rear Sets.
The silver color we chose also has a dress-up effect.
I thought it would be more cramped, but it was not so much and I got used to it quickly.
The Shift and Brake controls feel good and run comfortably.
Very satisfied overall!
View detail
Fits: HONDA CRF250L, HONDA CRF250 RALLY, HONDA CRF1000L, HONDA CRF1100L
Not that I'm complaining.
I have not tried riding without the rubber, but I think it is a good solution if you remove the rubber. Also, the quality of the product is good, and compared to Chromoly products, the Material:I think it's also good that Parenthesis is made of aluminum, and as a footpeg, it's quite wide, so I felt it's good that my feet don't get tired easily. View detail
Only looks
Silver was selected to match the Swing Arm.
The Seat height is also the same as the OEM Product, so nothing has changed in terms of performance.
It is a product that only looks good.
View detail
Fits: HUSQVARNA TC250, HUSQVARNA TC310, HUSQVARNA TC450, HUSQVARNA TC510, HUSQVARNA TE250, HUSQVARNA TE310, HUSQVARNA TE450, HUSQVARNA TE510, HUSQVARNA TXC250, HUSQVARNA TXC310, HUSQVARNA TXC450, HUSQVARNA TXC510
It also looks gutted and lowered.
The purpose of purchasing the Lowdown Link was not for footing or other issues, but to use the MOTARD vehicle completely as a road racer.
I put it on the picture, but I measured the ride height change from the rear axle to the exhaust system area, and it was 2.4 cm lower.
*This is not a correct measurement method and should be used only as a reference.
The amount of Front protrusion is also changed accordingly.
The look is now gutsy and low, and the atmosphere is to my liking.
It is important that you actually run and feel better.
Next, Spring rate will be changed after the actual run.
View detail
I'm satisfied!
I like the look, the texture, and the build quality of OverRACING!
If I had to make a complaint, I would say that it would be better if the position could be selected a little more. Also, I wish the Instruction Manual was a little easier to understand, because when I follow the Instruction Manual, I end up removing the parts 4 to 5 times.
View detail
More Classical
I replaced it with a new one that I thought would fit SR400.
It is secured with a single Plus screw, but it is aligned with the outside of the OEM's two Screw holes.
View detail
Fits: HONDA MONKEY125, HONDA LEAD125, HONDA ZOOMER-X (ZOOMER), HONDA XR50 Motard (MOTARD), HONDA XR50 Motard (MOTARD), HONDA XR100 Motard (MOTARD), HONDA XR100 Motard (MOTARD), HONDA XR100 Motard (MOTARD), HONDA XL230, HONDA Sh mode (MODE), HONDA PCX150 <ABS>., HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX Special Edition, HONDA PCX HYBRID(Hybrid), HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX
Good quality front fork dust seals!
These NTB Front Fork Dust Seals for the Honda MSX/GROM seem to be at least as good quality as the Honda OEM ones at a much lower price than the original ones! Recomended. View detail
Thanks!
Thanks to the wide range of lineups, it is nothing short of a miracle to find an external suspension lineup on a 30-year-old and superb Minor car.
The performance is also better than the crappy OEMSuspension!
View detail
Costa's strongest?
I had no complaints with OEMNormal step, so I replaced only the footpeg with HURRICANE's one.:Pair (for Left and Right) I decided to purchase this product because it was inexpensive with Type, which uses Normal pedal.
The included instruction manual clearly explained the procedure for replacing the Brake Side for ABS vehicles, so I was able to install it smoothly.
Repair Parts was fully supported, the quality was good, and I was satisfied with the better parenthesis.
View detail
Higher than BABY FACE
Except for the footpeg and heel plate (and color), it is the same as BABY FACE. The cost is about 12,300 yen higher than BABY FACE, so the cost performance is not good. I am satisfied with the color and position.
The car Both SidesChange arm uses the original OEM Product, but of the 9 companies I checked, only BABY FACE and YOSHIMURA did not make a dedicated change arm. I was concerned that the shift rod was leaning, so I installed Striker's Change arm and adjusted it by 2mm with a washer, and it became almost parallel to the car body.
Well, I don't think there is anything wrong with it being tilted, but I am concerned about the way it looks.
Footpeg is made by JagerLauftK.M.T. I like it, so I changed it. Also, the Brake Switch Bulb on the Right Side looks like an afterthought.
I wrote what it is, but I like it a lot.
View detail
Unexpectedly good
The HRCGROMCUP Regulation has given us the OK to start this year.
Purchased
I've been replacing Spring for a while now, so I'm just going to get cracking.
I was able to install it.
If you are doing this for the first time, you will need a Spring replacement tool.
It is good to be able to start from Initial 0. It is good to be able to change Initial by Course, Temperature and Condition.
View detail
KITACO suspension tool for the Honda MSX/Monkey
These KITACO Fork Thrust Adjustment Gauge Set are extremely useful in assisting you on setting the exact same height on both fork legs. They have 8 different height settings and are made of stainless steel which means they wont rust. Only improvement is that they could come with a ring to attach the two together, but you can easily add one. Overall it's a quality little tool from Kitaco! View detail
Fits: HONDA glom, HONDA MONKEY125, HONDA DAX125, HONDA HRC Grom, HONDA HRC Grom, HONDA NSR50, HONDA NSR80, HONDA NSF100, KAWASAKI Z125 PRO
Can also be used with Hollow Axle Shaft.
The name is "Axle Protector", but I installed it as a stress-up part because I thought there was not enough red around the front tire rather than to reduce the damage of the vehicle at the time of a fall. I already had an experience that I had a hard time to put in the Shaft when I removed the front tire by replacing it with KITACO's Hollow Axle Shaft, so this time I used DAYTONA's Maintenance Stand for Front. I was able to insert and remove the shaft easily because the vehicle weight was not applied. I think it is difficult to install by DIY because the fork hole, collar, and wheel are not aligned unless I lift up the maintenance stand or the handlebar, etc. I am satisfied with the red accents around the front tires, which are mostly black parts. View detail
Very platePad
Heel plate is a place that is easily scratched by shoes, etc., so we recommend that you attach a pad to the heel plate.
Speedra's pad is Carbon Style with good texture.
Installation is as simple as attaching it.
View detail
Fits: KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z1000J, KAWASAKI Z1000R, KAWASAKI Z1100GP, KAWASAKI Z1100R, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900)
Z1R
The Chain Adjuster on my Z1R was dirty and I was concerned about it, so I replaced it at the same time as the Axle Shaft. I am not sure how well it works, but I am Large satisfied with my car which is getting cleaner and cleaner. View detail
Fits: KAWASAKI Z900 (KZ900), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000 MkII, KAWASAKI Z1000 (air-cooled), KAWASAKI Z750 (air-cooled)
Z1R
We replaced it with an external MagTanWheel at the same time. It may not look the same at a glance, but I think my car is happy when the details are cleaned up. View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB, HONDA LITTLE CUB
Rear shock with good cost performance
[How is it used?
Bore up the LITTLE CUB and it became faster, but it bounced around on the fluffy Normal suspension due to road surface gaps, etc. and could not keep pace, so I replaced it.
We chose this product when we looked for something that did not change in appearance from OEMNORMAL to LARGE and was not too expensive.
Was the one you received as per Image?
I like the thinness of the OEMRear suspension and the large difference!
Plating and paint texture also felt overpriced.
Was the installation difficult?
Very Kan Tan. just replace one side at a time with OEMRear suspension.
The Instruction Manual says that applying Grease to the vibrating parts will make the movement smoother, so it is recommended to prepare it beforehand.
How was your experience with it?
Quantity:I did not expect much since it was cheap, about 10,000 yen for 2pcs, but I found it to be more than I expected.
In the past, the fluffy OEMRear suspension was bothersome when picking up road surface gapping, but this product absorbs the shock so smoothly that the rider can maintain his pace.
[Others]
The Cap Nut and Washer at the Rear suspension attachment point tend to be rusted, so it may be a good idea to have a new OEM one.
We also want to make sure that the Overtorque is not too tight to prevent movement.
View detail
It will be clean.
As is the fate of spoke wheels, no matter how hard you try to take care of them, over the years, rust will become noticeable on the wheel rim and hub, especially on the spoke.
The Spoke can be polished to some extent by Bonnstar or PIKAL, or if the Tire and Tube can be removed and the Bearing is to be replaced, the entire Wheel can be soaked in rust remover. However, in the end, the best way to clean the Spoke is to replace it with a new one.
There are no quality problems and it is very clean.
but the Rim group was very Large strange because it was the first time to work on it.
If you just want to assemble it, you can refer to the pictures you took before disassembling it.
Since there is no run-out machine, it is temporarily assembled on the jack-up car body, and several Tie Wraps are attached to the car body, and the upper and lower Quantities:Pair (for Left and Right) It's a steady process of tightening the screws.
To be honest, I didn't want to do it again, so much so that I thought I would ask a contractor to do it next time.
However, it was worth the effort, and when it is done, it is very beautiful. It is a new product, so of course I am very satisfied with the finished product.
Since the price is also there, it is a Recommendation for those who are familiar with Spoke groups and want to try Challenge, but otherwise, it is better to request Large Human Shops.
The work is Large strange, but the product itself is very satisfactory.
The model used is an xlr80, but since the front is customized and crm80 wheels are used on the xlr80, the hubs and rims are also crm ones.
View detail