Reviews
Fits: HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA NSRmini, HONDA NS-1, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS50F
Overhaul
I bought this because I wanted to build parts that would improve the performance of the engine overhaul of my NSR50. The assembly is a bit large since there is some press fitting work to be done. I don't have a hydraulic press, so I'm planning to challenge with Vise.
I don't know when I will be able to ride it, but I am looking forward to it.
View detail
no problem
I am very grateful for DMR's products since OEM is not available. I was able to install it without any problems. I can't say how durable it will be.
....。
View detail
Used on NSR250. Over cool measures in winter.
It is mid-summer so I can't benefit from it yet, but I changed from Thermo-less to low temp for winter over cool measures. I wonder if I need an electric fan no matter how much I open the low temp to 50C. My cooling specifications are 140mm jungle fan. (Thousands of yen) Thermoswitch, also in the jungle, to (about 900 yen) I think I keep 71-78 degrees Celsius at the setting where the fan turns at 80 degrees Celsius when the traffic is congested at about 35 degrees Celsius in the daytime in midsummer with Thermistor sticking into Thermo Case and Radiator cap changed to 1.3, Coolant is Heat block plus.
I'm hoping to reduce the warming up time in winter.
View detail
Fits: HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50
About MechanicalSeal
Thank you for your prompt response.
I put it together as soon as it arrived. 。 Water leak cured.
I guess it's hard if you don't have a certain amount of knowledge. ??
View detail
Can be used in the same way as OEM Product
[How is it used?
Used in Engine as well as OEM Product
How was your experience with it?
I have no problem at all using it.
How did it compare to other products?
I was not sure about the steel one, but I'm glad I went with this one.
[Points to note]
For installation, it is necessary to have enough skill to disassemble the Engine.
If you are not a professional, it is better to ask a specialized Motorcycle store for help.
It's good.
View detail
I put it in for water temperature in the summer:....
The low temp Thermostat has arrived and will be installed immediately.
I used Type 2 this time, considering the winter season.
The work time is about 30 to 40 minutes even if you take your time.
My vehicle is an MC18, but I think the work time will probably be the same for any model.
I have done a test drive immediately after installation.
The temperature on the day of the run is approximately 30 degrees Celsius (in the city).
I have driven about 100 km on city + mountain roads, and I think the temperature rise has slowed down a bit.
While driving in Nagoya city, stop&go is repeated so that once the water temperature rises, of course, it is almost the same as in NORMAL.
The only thing I would say is that it is a little better because sometimes it is below 65 degrees.
On the mountain roads, as long as the pace was reasonable, I was calm at 60-65 degrees.
As a result, I honestly thought it was fine for me to have it or not.
Maybe the 18 Radiator is so crappy that it's no good! I wonder if the Radiator after 21 will be able to experience the effect?
Probably expensive, but I feel that for 18, Radiator should be changed as well.
View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Used for MC21. Reliable quality.
I needed a MechanicalSeal to fix a coolant leak, and I used this product, which has the same performance as OEM products. View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Quantity:I'm thankful it's Set.
Gasket etc. required when changing water pump is Quantity:I'm very grateful for the Set. View detail
OEM Discontinued
I'm very happy to see that you have released these parts as the OEM products are no longer available.
The installation was just as good as the OEM one, and I can use it normally without any strange noises.
View detail
Inexpensive but good quality.
I used it on my NSR Overhaul.
I was worried about T2RACING, but I decided to go with DMR.
Should I have gone with MechanicalSeal-less?
View detail
It's cosmetic.
I had a hard time with T2's, but I decided to go with DMR. View detail
The Savior of NSR
We chose the DMR because OEMs are discontinued and therefore unavailable and other companies' products are more expensive
MechanicalSeal Quantity:Because the Set was also purchased, the parts necessary for the exchange of the water pump were able to be prepared
These parts are very helpful these days when OEM parts are no longer available
View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Convenient
A complete set of what you will need is Quantity:The set comes as a set, so ordering is easy
And it's cheaper than OEM parts
If you want to order OEM Parts by looking up the number and ordering OEM Parts, I thought it would be much better to buy this one
View detail
Bulletin board street
I bought a reputable DMR made in Net reviews.
It is quiet and nice as described! It was cheap so I was a little worried but it seems good to make it solid.
The Gold genus made by a company that I used before was bothering meow and sounds, and the Coat which I expected was also torn off.
It seems to be higher quality than OEM? We are looking forward to the durability of MCNylon!
View detail