Reviews
Fits: YAMAHA MAJESTY125, YAMAHA MAJESTYX, YAMAHA CYGNUS X, Others
First DoctorPulley
I have only used Round Type's Weight Roller so far.
Setting is also at a standstill
Buy DoctorPulley to try it out
CYGNUS Taiwan Type 2 is standard 9 Grams, so buy 9 Grams
I had gotten 8.5 Grams before that.
8.5 Gram installed first
Round Type's Weight Roller also uses 8.5 Grams, so I wanted to see how it would change with the same Grams.
The texture is crazy good.
Durability will be verified in the future.
As an imp
8.5Gram with a Fee Ring with a Weight Roller that is lighter than 5Gram.
Turns well.
However
Harder to turn than Round Type at near maximum speed, and headway is made.
Headed at 8000 rpm (descending)
Center spring Spring rate is determined to be too high.
When I switched back to the center spring I was using before, it started to turn and the top speed started to increase nicely.
9000 rpm (down)
Perfect from bottom to medium speed.
Only the high speed range is sensitive.
I just repurchased 8Gram.
There is a conflict with Center spring.
I'd like to try different weights.
It is a little more expensive than Round Type.
I think Mr. WeBig is the cheapest in Total so far!
View detail
Fits: YAMAHA MAJESTY125, YAMAHA MAJESTYX, YAMAHA CYGNUS X, Others
Outstanding durability!
After all, it is a Weight roller that has always been my favorite because of its excellent durability.
Prices are lower than before, making it easier to buy.
It is used in CYGNUS type 3, but the Secondary set is BW's125.
Spec. with Bose Washer at 0.9mm and 9.0g, the gear shift was at 8000 rpm.
KICKDown is also recommended because it has good Response and acceleration & top speed are not a problem - I would recommend it.
View detail
Fits: YAMAHA , YAMAHA JOGPoche, YAMAHA JOG50, YAMAHA BJ, YAMAHA VINO, YAMAHA APRIO, YAMAHA APRIO, YAMAHA SUPER JOG ZR, YAMAHA SUPER JOG, YAMAHA JOG remote controlZr, YAMAHA JOG remote controlZII, YAMAHA JOG50, YAMAHA JOG remote controlZr, YAMAHA JOG remote controlZr
Clutch outer replacement
APRIO (4jp5) The clutch outer of the "M" was worn and slippery, so I bought it for a replacement.
I had changed only the clutch first, but it started to slip a little when starting off, so I decided it was time to change it.
Inside of Clutch outer (Clutch contact surface) However, the old one was smooth as if it had been mirror-finished, but the new one had the same rough pattern as the surface, so I thought Clutch had a good bite.
I haven't done a test run yet after the replacement, but I don't think it will be a problem since there are no problems with the original running.
Outer clutches are supposed to be replaced when the color of the clutch burns out, so from now on, the clutch and the quantity:I will change it with Set.
View detail
Fits: KYMCO RacingKing180Fi [Racing King]., KYMCO RacingKing180Fi [Racing King].
Scooter's personality changes so much when you change the pulley.
The acceleration in the start dash, low to mid speed range, and mid to high speed range feels overwhelmingly fast.
Physically, the weight of the Motorcycle has been lightened? I think the weight of the motorcycle has been lightened.
As per Title. changing Pulley makes it a different Scooter.
I can recommend it.
View detail
Fits: YAMAHA Aero X100, YAMAHA Grand Axis, YAMAHA RX100, YAMAHA BWS100 (Bewith), MBK NITRO100, YAMAHA Aero X100, YAMAHA Grand Axis, YAMAHA RX100, YAMAHA BWS100 (Bewith), MBK NITRO100
You can feel the change right away after replacement.
The belt needs to be broken in. Once the belt is broken in, you will definitely feel the change in your body. Since it is shorter than the original product, high-speed range can be expected. In addition, with the pulley side tune, both the early and middle ranges were satisfied! View detail
Increased power performance at an affordable price!
Upgrade springs at a low price while replacing genuine springs! very good to do I was satisfied with the packaging and finish, and I was able to feel that the power was clearly transmitted better than the original product. The fact that it looks more powerful in yellow is a bonus! This is a list of essential tunings View detail
Fits: YAMAHA Axis 90, YAMAHA Axis 90, YAMAHA Axis 90, YAMAHA Jog (2 cycle), YAMAHA Super Jog Z, YAMAHA Super Jog Z, YAMAHA , YAMAHA JOG-EX, YAMAHA Axis 90, YAMAHA Jog Z, YAMAHA Grand Axis, YAMAHA BWS100 (Bewith), YAMAHA Grand Axis, YAMAHA BWS100 (Bewith)
Improved performance with reliable lightweight!
It is definitely lighter than the original and has larger ventilation holes, so it is by far superior in heat management and improves response. I am satisfied with the packaging, finish, performance, and price of the product. Since it is a product from a company with a long history of data, I was able to use it with confidence. Thank you. View detail
Put into used CYGNUS Type 3!
This is from someone who has only driven Mission vehicles.
Almost installed on a NORMALCYGNUS X-3 model.
The condition of the vehicle is that the Belt, Roller, and Clutch Shoe were replaced after purchase.
Since the start of the engine revs up to high rpm, the acceleration feeling
I don't feel any depression and it blows up.
This is when you are aware of a little bit of sudden acceleration in a Mission car.
Similar to the starting point.
This increase and maintenance of RPMs is excellent, and the later motors are
Acceleration no longer irritates me, but Clutch Spring and
I feel Center spring is not keeping up.
(I probably should have purchased the Clutch Side at the same time.)
In the city, the sound of the exhaust system is loud due to the high rpm of Start.
The drivetrain of the Scooter can not be described in one word because the overall balance is that of Large.
If the neighborhood has a wide road with frequent merging onto the main road
Might be good as a first Custom
View detail
Fits: YAMAHA BWS(BWS), YAMAHA BWS(BWS), YAMAHA JOG (both FI Vehicles), YAMAHA VINO, YAMAHA VINO(2Cycle), YAMAHA VINO(2Cycle), YAMAHA Box, YAMAHA Old JOG (27V|48F|1HHH|1KX|1RN), YAMAHA Old JOG system (2EX|2TA|2TE|2JA|3CP), YAMAHA BJ, YAMAHA JOG-EX, YAMAHA AXIS 50, YAMAHA AXIS 90, YAMAHA APRIO, YAMAHA GEAR, YAMAHA GEAR, YAMAHA JOG, YAMAHA JOG (2Cycle), YAMAHA JOG 80, YAMAHA JOG90
Necessary and sufficient.
I bought it for Setting.
4.5gSpec. and measured with a scale calibrated with weights, the error is sufficient to be at mostLarge0.03g.
The Body has the same shape of Both Sides, which does not seem to be oriented to the Body.
Durability is unknown, but I haven't seen any reviews that say it's bad, so I guess it's not a problem.
View detail
Centrifugal clutch.
I installed the clutch in my scooter over a year ago. After starting the engine, it turned out that it had quite large radial runout. I was afraid that it would jerk when starting, but I dismantled it and have been driving the Honda for over a year. Last fall, it started jerking a bit when starting the scooter, so I'll have to check it out by spring this year. -------------------------------------------------- -------- I installed the clutch in a scooter over a year ago. After starting the engine, it turned out that it has quite a large radial beating. I was afraid that he would jerk while starting, but I dismantled him and I have been like Honda for over a year. Last fall, it started to jerk a little while starting with a scooter so I will have to check it until spring this year. Powered by Google Translator View detail
Unlike NORMAL, it is clearly harder!
[How is it used?
Mainly for city driving.
We have been using OEMSpring, but now we can get it at a lower price with Webike's OutletSale and install it.
The current setting is OEM Torque Camshaft + F.C.C. Sports Clutch + F.C.C. Clutch Spring.
Weight Roller8.5g×6pcs
Pulley is JapanSpeed + ad PRORamp Plate
Was the one you received as per Image?
Shorter than OEM, stiffer than OEM!
Refreshing Blue color.
The strength is clearly different when shrunk with OEM.
It's hard anyway!
Was the installation difficult?
12%Up is much stiffer.
The difficulty level of incorporating Belt, which could be easily dropped in with a grip, has clearly increased.
Small student, it can't be helped that I have a weak grip, but it was hard and it became Large strange to shrink.
You may have to strengthen your grip or get a Clutch SpringCompressionTool.
How was your experience with it?
The engine starts at a noticeably higher rpm, and the clutch finally starts to meat at around 5500 rpm to 6000 rpm.
Compared to the OEMClutch Spring, the situation does not start running until the rpm is increased.
In the case of a full Axel with Zero start, the rpm rises momentarily to 9000 rpm, then drops to 8000 rpm, and it seems to accelerate while maintaining a high rpm.
The speed at each rpm is 6000rpm→60km/h range, 7000rpm→70km/h range, 8000rpm→80km/h or higher to the highest speed.
After shifting, the speed does not reach 9000 rpm, but only increases at 8000 rpm.
I thought I had a pretty good Setting before I added Clutch Spring, but now I have to start all over again.
We have our feet firmly planted in the swamp of the drive train.
Image-wise, I have a feeling that fuel economy is going to worsen considerably because it is like driving a manual transmission car with the car in first gear and pulling it to a higher RPM.
Both exhaust and intake noise became louder.
In the case of Normal spring, the rpm was down to 7500 rpm, so the Timing of the gearshift obviously changes to above.
I will be setting up with a Weight Roller in the future, but I have already purchased Torque Camshaft as an Other Brand Product, so I will continue to open the Crankcase every day.
View detail
Fits: SUZUKI Address V100, SUZUKI Address V100
KN Project SEA BASS type Slide Piece
Purchased a new Slide Piece for replacement, the Ramp Plate itself was also replaced by KN Kikaku's one and it works fine.
Even if only one Slide Piece is missing, it will be impossible to build a drive system, so it is better to leave it in Stock.
Thank God they had it in stock.
View detail
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V125S, SUZUKI Address V125S, SUZUKI Address V125S, SUZUKI Address V125S Limited, SUZUKI Address V125S Limited
Used for ADDRESSV125 K7
Used in K7 with 100,000kmOver
11gWeight Roller, in combination with KITACO Kevlar belt
Even with the Gymkhana chic running, you will feel the acceleration there!
View detail
The parts are different.
I purchased this part for my KYMCO Agility 125, but it was a HondaDIOSeries part.
I chose the right model, but the shape was different.
Webike has the wrong model of car for which it is compatible.
View detail
Fits: YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA Jog Aprio Type 2, YAMAHA Jog Aprio Type 2, YAMAHA Jog Aprio Type 2, YAMAHA Jog-A-Prio, YAMAHA Jog-A-Prio, YAMAHA Jog-A-Prio, YAMAHA Apprio, YAMAHA JOG ZR [YG50Z] 1998, YAMAHA JOG ZR [YG50Z] 1997, YAMAHA JOG ZR [YG50Z] 1996, YAMAHA JOG CASUAL [YV50C]., YAMAHA JOG CASUAL [YV50C].
Good
I think that the range of setting on the Secondary side will also be expanded. I think they are seriously considering the performance. The weight is lighter than the previous product. View detail
Fits: HONDA READ 125, HONDA READ 125, HONDA READ 125, HONDA PCX
It will last for 20,000 km with plenty of time to spare!
I always use it as a V Belt for my PCX which I usually use for commuting.
The last time I replaced it was at 50,000 km, and now it is over 70,000 km and has been used for over 20,000 km, so I have replaced the Weight roller, Slide Piece and Quantity:I replaced it with a set
The V Belt that was removed was very clean and did not look much like a new one. 。 The width was measured and found to be only about 0.1mm less than the description of the product. "The limit is 1mm or more less than the specified width dimension." It is unlikely that the amount will be reduced to the Spec. limit under normal use.
However, if you look closely at the reverse side of the Belt, you will see fine cracks, which is a unique feature of this Belt, Dual structure of standard rubber and high elasticity heat resistant compound rubber. However, the limit of the spec. is around 25,000 km.
The weight roller that was replaced at the same time after 20,000 km is not worn unevenly, but it seems to be a little smaller than the new one. 。 According to the actual measurement, all rollers seem to be 0.3mm in diameter and a little less than 1mm in circumference, and they may be 1 to 2g lighter. 。
Recently, fuel consumption has been below 45km per liter more often than not, and I thought it was because of the colder weather, but maybe it was because the weight roller was lighter and the emphasis was on acceleration. 。
Considering this, I would say that the weight roller, slide piece, and V-belt should be replaced at 20,000~25,000km, and the Torque Camshaft should be disassembled, cleaned, and greased up in quantities.:I think it would be better to do this with Set.
View detail
Fits: YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500
good strong belt
I've bought these belts before from webike, and they last a long time.when I changed it, it still looked like new, with no cracks. And the price is right, which fits my budget. View detail
Fits: YAMAHA CYGNUS X FI, YAMAHA CYGNUS X SR, YAMAHA CYGNUS X 19
Used for commuting CYGNUS
[How is it used?
I used it on my CYGNUS X for commuting.
The pulleys use KITACO's Power drive kit.
The 7g that came with the KITACO kit was too light and the Engine turned too much, so I used the OEM 9g,
That was not enough to bring out the full flavor of the Power drive kit.
We chose 8g this time, which would be just the right amount of salt between KITACO and OEM.
Was the one you received as per Image?
If you use non-OEM Weight Roller, DAYTONA is the best choice.
The image is OEM's Weight, but DAYTONA's surface Material is also Color:Gray, but made of a similar material,
Durability is expected to be high there.
Was the installation difficult?
It is not particularly difficult, and if you can remove Pulley, it is easy.
How was your experience with it?
Shifting speed is roughly 7300-7400. The maximum speed is still lower than 9g.
but the acceleration just shifts at a rpm that feels like a nice Power.
If you take maximum speed or acceleration, CYGNUS would be acceleration.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not really!
View detail
Fits: HONDA gyro canopy, HONDA LEAD 50, HONDA LEAD 50, HONDA TODAY, HONDA DIO(4Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA TACT, HONDA TACT, HONDA TACT, HONDA ZOOMER, HONDA SMART DIO, HONDA SMART DIO, HONDA SMART DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO
Aging
Used on a HondaTACTA-AF09Courreges TACT85.
I was wondering if there were any parts that would fit since the model is quite old, but I wanted to build it with non-OEM parts, so I bought it.
KM Kikaku Parts has been used on CYGNUS and has been doing well, so we purchased the parts from KM Kikaku, which is famous for its mini bikes, because we thought they would be durable.
There was a little BALI, but it was quickly cleaned up and installed.
I don't know how it feels since it has only been installed for about 100 km, but I think it is large and strong since it is a just fit.
View detail