Reviews
good qulity
This is including baral fuse .Very good qulity outer matirial.eazy to fix without any modification.amon produts are always good for DIY enthusiasts. View detail
For easy power pickup
Used to get power for drareco
Easy power supply from Fuse box
However, the Wiring is caught on the Cover, so a little modification is required.
View detail
Easy to remove.
Power can be easily removed by simply replacing the Fuse.
I use it to charge my phone and it works fine.
I think a little modification will be needed to get Wiring out of the junction box lid, etc.
View detail
Just replace it.
I purchased a Flat Type Fuse Power Supply to install a D-UNIT made by DAYTONA. Before purchasing, you need to open the Fuse box and check from which power source you want to secure the power supply, and buy the one that fits the FuseAmpere. Installation was very easy as I only had to replace it. View detail
It's easy!
Recommended for those who are unfamiliar with power supply extraction.
Note that you need to check the Plus side in the Fuse box. If you make a mistake, the fuse may be cut off. In GB250 CLUBMAN, it is OK to replace the fuse as shown in the photo, but the wiring from the fuse makes the fuse box tight. The wiring from the fuse will cause the fuse box to be tightened, but it should be sturdy and large enough not to worry about.
View detail
Very convenient.
This Connector is used to get power from the Mini Flat Type Fuse.
This is very useful.
I often use it as a power source for my car. Most of the common vehicles have a fuse box at the foot of the vehicle.
I need to pull power to run the DriveRecorder, Radar detector, etc., but the Cigar lighter socket makes it look rather ugly...
In the case of a motorcycle, there is no Cigar lighter socket in the first place.
The Fuse is taken out from 15AFuse, but since it is via Pipe Type Fuse 5A, it will fuse if a load of 60W or more is applied. (The Fuse that is connected to the MainFuse is 15A, so the allowable power of the MainFuse is 180W. Paradoxically, if you use more than 120W on the MainFuse side, the Main will cut off if you use more than 60W)
A fuse box with a lid requires some ingenuity in terms of how the wiring escapes.
View detail
I didn't think it would be this easy.
DAYTONA
Attachment Power Supply Unit D-UNITPlus (DeeUnitPlus)
https://www.webike.net/sd/24232600/
Used to take ACC power from the
I was worried about whether the lid of the FuseBox would close properly, but it did, to the point that it never closed completely but not problematically.
Need to check continuity and be careful about the direction of insertion.
I installed a pluggable Fuse to get power before the current flows through it.
View detail
Easiest power extraction
There are three simple ways to extract power from the Gixxer 2020 MODEL~.
Bullet terminal terminal for attachment hidden under the tankLeft Side, not accessible without removing the Side cover
Computer diagnostic coupler in the ETC storage space under the Rear Sets.
And from the Spare sub of the Fuse BOX under the Front seat.
This is the quickest way to get it from here, so this guy is always there for us.
I usually use Bullet terminal, but this time I used Terminal, which is quite easy to use.
View detail
For Woofer installation
It can be used to power a subwoofer installation.
It is long enough to roll from Battery to Power amp for peace of mind.
It is of good quality and provides a stable power supply.
View detail
easy and convenient
Easily get constant power supply from the Fuse box.
The terminals are two-way, so they can be used to install multiple electrical components at once.
It is useful because it is easy to install.
View detail
Convenient for taking out power from a flat Fuse.
This product can be easily powered by simply replacing the fuse in the Motorcycle's fuse box. No tools are required, so it is a recommendation for those who are not good at wiring work! View detail
Very easy to secure power supply
[How is it used?
In order to add electrical components, we decided to take power from Fuse, which is energized in conjunction with Ignition key.
Was the one you received as per Image?
It was exactly as it looked in the picture; it was hard to tell what the Wiring looked like coming out of the FuseBody, so that was a bit of a concern.
Was the installation difficult?
The installation itself is easy since it is just a matter of replacing the existing Ignition20AmpereFuse, but some ingenuity is required since the wiring must be routed around the FuseBOX lid so that it can be closed. Since the wiring is coming out of the FuseBody in an upward direction, in order to make it turn 180 degrees, I had to cut off a part of the pate that was heaped up to reinforce the root of the wiring attachment part, so that the wiring could turn 180 degrees without any difficulty. The following modifications have been made to allow UTurn.
How was your experience with it?
It was energized with Ignition keyOn without any problems.
[Included Parts:were they on?
There is a 10Ampere Fuse tube in the middle of the wiring. This time, it was used as it is.
[Was there anything that disappointed you?
Not particularly
View detail
Power extraction without damaging the vehicle body Harness
It is an item that can get a branch power supply by replacing it with Fuse.
When it comes to taking power out of your car or motorcycle, you may be more likely to Image an Electra tap.
It's certainly useful and widespread, and if you ask a motorcycle shop to install electrical equipment, they will often use an Electra tap.
However, as you can see from the structure, they are not only damaging to the harness on the car body, but they are also unreliable and often become a source of trouble over time.
In this case, this product can be used by replacing the Fuse, so it will not damage the harness on the car body.
By the way, personally, it is iron board to replace this with HeadlightFuse and use it as a power supply for Bach direct Relay.
I've been running it this way for years on multiple Motorcycles and have never had a Trouble.
It's one of the most reliable power extraction methods.
View detail
Get the power!
I used it to get the ACC power supply for my drrorecorder.
It's so convenient to take Plus just by replacing Fuse with Ideas product!
I'm sure a lot of DIYers love it.
View detail
very useful
I bought this for KAWASAKI NINJA1000SX, 2020 model. Because it is connected to navigation, mobile phone charging, and driving recorder, it is necessary to connect the power supply from the car. I bought 2 of them this time. This E577 also needs E576. The connection is simple and you can use it when you plug it in. Never worry about not having enough power in the car anymore. ---------------------------------------------- This is in order to buy KAWASAKI NINJA1000SX, 2020 models use. Because navigation phase, cell phone charger, tachograph, so that the power from the vehicle access. This bought a total of two, but also this E577 E576, simple connection, plug able to use. No longer worry about the car enough power. Powered by Google Translator View detail
very good
I bought this for KAWASAKI NINJA1000SX, 2020 model. Because it is connected to navigation, mobile phone charging, and driving recorder, it is necessary to connect the power supply from the car. I bought 2 of them this time. This E576 also has E577. The connection is simple and you can use it when you plug it in. Never worry about not having enough power in the car anymore. ---------------------------------------------- This is in order to buy KAWASAKI NINJA1000SX, 2020 models use. Because navigation phase, cell phone charger, tachograph, so that the power from the vehicle access. This bought a total of two, as well as this E576 E577, simple connection, plug able to use. No longer worry about the car enough power. Powered by Google Translator View detail
I've got power.
I bought this to power my Ignition Illumination. It is very easy and reliable to power.
I used it for Light relationship.
View detail
Power from the Fuse box
There are many ways to use your new Motorcycle with a USB power supply to make your Smartphone Navigation experience more comfortable.
Direct connection of the Battery
Connect to the wiring that runs when the key is turned on (appropriate wiring around the handlebar).
Connect to the Fuse box
Does the Harley's Battery seem to wear out more than a domestic car when it's in storage? I think that Risk is high and give up the bacchanal even with Fuse if possible.
I thought it would be easiest to connect to the appropriate Wiring around the Handlebar, but this was also a no-no because I didn't want to mess with the Cable of the vehicle body.
Then, inevitably, let's get the power out of the Fuse box! That's when I came across this product from our friends at DIYUser, Emon.
First of all, check the Ampere number of the Fuse that takes power, and confirm the conformity of Emon. The installation is completed only by removing and inserting the Fuse.
The Ampere number for this product is
・7.5
・10
・15
・20
・30
I had a 15A in my Harley (XL1200S).
Harley has a Fuse box at the bottom of the Seat, so you can remove the Tank etc. and run the Wiring neatly to the Handlebar and it's done. After that, use the USBQuantity made by DAYTONA which I have purchased separately.:Combine with the power supply of the Set and it's done.
I have to get this stuff on.
・Tie Band
・Pliers
It's easier to do a lot of things if you have
It is still a short time after using it, but the Fuse is attached, and the power supply is excellent in cost performance without a problem because it is properly removed.
In contrast to the latest motorcycles, when a motorcycle is already in the old-school range, taking a new power supply is likely to put a lot of stress on the Battery and Wiring. In order to avoid unnecessary troubles, it is important to avoid modifying the original wiring as much as possible.
It has become commonplace for motorcycles to be equipped with smart phone navigation and draco systems, and it has become a customization to figure out how to get power to the bike. I'm going to try Challenge with a different mechanism.
View detail
Used to power the ETC
important item
[Was there anything that disappointed you?
nothing special
Do you have any wishes or improvements you would like to make for the Manufacturer?
nothing special
[Do you have any products to compare it to?
nothing special
Frequently Asked Items
What made you decide to buy?
I used it to install the ETC on my High ace, I didn't know that the Fuse comes in multiple sizes and almost bought a size that didn't fit. "Low Profile. is compatible.
How was your experience with it?
I'm happy with the power supply without any modification.
Was the installation difficult?
Just remove the existing Fuse and replace it.
【Please tell me the installation point and hang】
When you remove it, you can use radio pliers or special tool.
[Was the Instruction Manual easy to understand?
There is none
[Included Parts:were they on?
There is none
[Others]
There is none
View detail
I use it all the time, not just for motorcycles
Quality is solid; used for Wiring connections on SEA BASS Motorcycles
You can buy it as a Stock if you order it with other things at We-BigSale for a discount Maybe
View detail