Reviews
Installation almost broke my heart.
If you don't have the skill to tinker with motorcycles, don't do it by yourself. The instruction manual says to remove the headlight, but since I had installed various external parts, I could not remove the headlight and it took me about 3 hours to complete the installation using all kinds of tools. I recommend you to have it installed at a shop for about 5,000 yen.
As a product, HONDA's Logo is a good product with a good parenthesis and a custom feel.
View detail
This one's better.
I was surprised to see the Horn on the wall, so I immediately went for this product, but at first I put on Black, but I couldn't see the letters and the texture was too cheap, so I switched to Plating. View detail
For HONDA Emblem
After converting a monki−125 to a down fender, I bought it to put a HONDA Emblem on it.
It's not too bad, not too bad … but I'm a bit worried about Emblem because it just fits in.
View detail
It's a must have Sticker for KATANAAnniversary. 、、、、、
Tank Sticker is a must for KATANA 90th Anniversary.
I thought about buying a new one, but it was sold out as an official SEA BASS Parts.
I had no choice but to make my own, and then I found them at Webig! I was so thankful and immediately bought two of them.
When the original Sticker was removed and the purchased Sticker was applied, some of the print on the edge of the transparent Seat was taken away by the transparent Seat when the transparent Seat was removed.... As a result, a part of the print was peeled off. It was brand new.... I am very sad, even though I went to a lot of trouble to buy it.
I'm patient now.
View detail
So so
Was the one you received as per Image?
It is quite cheaply made.
Was the installation difficult?
Easy
How was your experience with it?
It looks better now.
[Included Parts:were they on?
Yes
View detail
Wow that's cool
After all, it looks different without it. View detail
For Racing concept Small but not for mini!
[How is it used?
Striker's Racing conceptFull Exhaust System is used on a YZF-R25 that is being racerized.
Although the Silencer is located in a position that is less likely to be damaged than a normal Exhaust System due to repeated falls.
The glass wool was worn out and was a mess, so I bought a new one while replacing the glass wool.
Was the one you received as per Image?
The design and texture were just like the Image without any complaints, but... the Size "Small" It's big on Habit of Habit!
Apparently, the Racing concept of the R25 is For Power mini of Emblem seems to have been correct.
It's my fault for not checking properly.
By the way, the one for Power mini is "part number : 0SREB5". Check Emblem's Design carefully before buying.
Was the installation difficult?
I have not installed it because it is too big, and I don't want to put a strange load on the silencer band.
If you can do a normal Silencer Overhaul, this is an easy task.
Just skip Rivet's head in Drill and Riveter with liquid Gasket on the new Rivet.
How was your experience with it?
Too big for Silencer up to 250cc! But it's too good to waste, so I'll put it on Silencer's Reverse side and make it DoubleEmblem....
[Included Parts:were they on?
RivetQuantity in a courteous manner:It comes with 2pcs! but the Material:It was an Aluminum umbrella and the shaft was rusty with an iron Rivet.
[Was there anything that disappointed you?
Emblem from Racing conceptSeriesStandard Equipment. I would be mistaken if I were told that this is the case.
Since we know which Silencer is being used for which buzz, please make sure that the Manufacturer has a good setup.
View detail
fashion-conscious
Appearance oriented, self-satisfied, cosmetic? View detail
BRC BRC Front emblem
Good for dress-up.
I want not only Black but also Red, Blue, and Yellow colors.
View detail
Installation.
It was a little difficult to install. I like the quality of the product! View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750 (air-cooled), KAWASAKI Z750 (air-cooled), KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750FX, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750FX
Although it was felt comparatively high-priced a little, they were the components which it is and regards as good.
Although it was felt comparatively high-priced a little, they were the components which it is and regards as good. View detail
Compared with the original factory logo, the quality is indeed worse
The edges are not sharp enough, the paint finish on the surface is a little holey, and the quality is not as good as the original factory logo. In order to reflect "different", there is only this choice, but manufacturers should improve the quality, do not live up to made in japan ---------------------------- ------------------------------- The edge is not sharp enough, the surface of the lacquer surface is a bit hole, and the quality is not the original logo. In order to reflect ""unique"", only this choice, but manufacturers should improve quality, don't let go of Made in Japan View detail
The texture isn't great, but...
The texture isn't great, but the look from the front is good.
Exclusive design of the mounting bracket makes it easy to install. 。 I don't like how close Plate and Body's Clearance is, so I adjusted it with Washer.
Everything else is fine.
View detail
Caution
If you are installing at the same time as the Takekawa Front Down FenderBracket Kit Put the OEMBracket back in place as described in the Instruction Manual Then, the impact of the slightest bump will hit the OEM and Takekawa Bracket
It's hard to understand KITACO's Instruction Manual Do not use the OEMBracket for installation
View detail
For better or worse, it's worth the price
First of all, the good thing is that you can choose the Logo option of Emblem and the Large character type That's good
The price is lower than other manufacturers' products, but the quality of the plating is good enough DOREMI's are like Light rim's Plating, the surface is LusterLuster Type (Other Manufacturer's Plating products have textured surfaces Is this a personal taste?)
As for Alpha bets, once you fit them in, you won't have to worry about BALI too much
The only thing I felt that the price is reasonable is that the emblem is on the Left Side from the shape of the bracket Being out of sync
The lower part of the Emblem interferes with the Stem so that fine adjustments are not possible when tightening the Bracket I cut the interference part
If you're worried about the subtlety of the Center not appearing, Recommendation is a I can't do it, but for this price, I think it's good enough for those who don't mind
View detail
I think I'm done
I tried wearing it on my Z900RS, but it's been in use for less than six months The black part comes off in the
It's a bit early, isn't it?
Bracket and Emblem are quite expensive when added together, so let's give it a little over a year Manufacturer
View detail
Z900RSExclusive Design Not Universal in Use Product
The attached bolt is short and it has a hard time to install If the bolts are 3mm longer, I do not have to do such a thing In addition, the adhesion of the edge is not good as for Black which seems to have painted on Plating
The notch in the Horn part is also in the shape that matches the shape of other models, and Z900RS seems to snatch the Horn becomes
PMC Inc. should consider what impressions people will have of PMC Inc. when they buy it, for starters
View detail
Dress Up Parts
Installation itself is easy
For DOREMI COLLECTION, the letters inside are made by pushing in a pin, so there is no pin folding Be careful not to use it Especially when you choose a kawasaki character, the last i is separated from the point and bar at the top, so be careful! Required
View detail
I highly recommend this one!
If you're a Yamaha fan, I highly recommend it! The texture is thick and luxurious, and it's cool! But the price is a little high - other than that, I'm satisfied with Large View detail
Normally
With Plating Plating intending to tighten to a vehicle with a blurred feeling,
I tried choosing Black as One Point.
It is okay even if the gold price is a bit higher, so I am happy to have Black chrome.
Is it okay with a Gold amount of about half price of Bracket sold separately?
Oh! Because I painted Screw's head visible on the surface Black by myself
The standard is Silver color Screw.
To make no mistake
View detail