Reviews
Fits: HONDA GORILLA, HONDA MONKEY
Can be used for groms.
[How is it used?
Rear suspension was replaced and ride height was increased.
Was the one you received as per Image?
Well, it's CQuality, but it's cheap, so it's OK.
How was your experience with it?
The angle is now as per Image.
[Points to note]
Side stands switch must be cancelled
Also, Screw can be put in from the back.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
For those who use in Grom, please buy Side Stand Switch Canceller
View detail
Fits: HONDA Ape 50, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 50, HONDA XR100 Motard, HONDA XR50 Motard
I am concerned about the strength…
[How is it used?
With the Rear Sets installed, the GCraft Side Stand Bracket was installed, but the mounting point was lower than the Normal Bracket, and it became necessary to shorten the length of the Side Stand, so we decided to purchase it.
Was the one you received as per Image?
Aluminum Cut-out is Parenthesis better than Image.
Was the installation difficult?
Spring hooks are easy to install.
How was your experience with it?
No problem, but Material:I am concerned about the strength because it is aluminum.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
The tilt is now good.
The side stand was getting tired and the tilt was becoming large. When the road was leaning Left, the STAND was leaning so much that it was a little heavy to get up, but now it looks good. View detail
crf250RALLY50 Corresponds to parking lot tilt
The parking lot of the house is slightly tilted.
The installation of an Aluminum Rear box.
Due to the above two points, there was a concern that the product would topple over to the Right Side when parked.
Therefore, Side Stand was shortened.
The installation was done by RED ZONE, from whom we purchased the Motorcycle.
After installation, the tilt was Larger on level ground, but no problem. Of course, there was no problem in the parking lot of the house.
The product looked great and was satisfactory.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-R125
Earthquake protection.
There have been a lot of earthquakes recently.
I was worried about OEMSTAND, so I decided to go with something with a lower center of gravity.
good point
Simply replace the existing STAND.
I put it in Handlebar Lock, 1st gear, and set it to this STAND, and it was Large sturdy at about 5 intensity of the earthquake.
A bad point
It is better to have two people for installation, one who is holding it down and one who is attaching it.
Short suspension compatible, but OEM suspension is also available. How about for earthquake protection?
View detail
![[Optional Parts] Replacement Chip](https://img.webike-cdn.net/catalogue/images/55193/ze56_8909_TS.jpg)
It was early.
CRF250RALLY5019Standard
By MOTARDization
I could get rid of my standing position!
I'm glad I bought it
View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
Installation of N-MAX Side Stand Switch Canceller
My friend's Yamaha N-MAX is not able to run the engine without the side stand, which is inconvenient.
You are responsible for any problems that may occur since you are removing a function that is attached for safety reasons.
For safety reasons, I would not recommend it, but my friend seemed to be satisfied with Large.
The work itself is easy, as it is only a matter of replacing the Cover if it can be removed.
I think someone with a SuKill can make it on their own.
Well, since it is inexpensive, at 330 yen, you can't go wrong with buying it.
View detail
On gravel or unpaved surfaces.
When I park my motorcycle on gravel, it becomes unstable due to vibration and other factors that cause it to tilt, but this product made it stable.
It also prevents the ground surface from being scratched and the color of the Side Stand from being stained when parking a heavy Motorcycle, even on a dirt floor condominium.
Since it is a PlasticMaterial, it seems to be weak in strength, but it has managed to withstand a motorcycle weighing 250kg with a little distortion.
View detail
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
certainly
It is true that it was very good because it made it easier to STAND, but if I banked too much on the winding, it was scraped and bent. I think it is because of up-down because of the mountain road. View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Very large effect on overloading of the Carrier, which is common in CT125.
It increases stability to the point where OEMs are frustrated as to why they could not do this.
The balance of the OEM is such that the front of the Carrier floats when you press down on it with your hand, even when unloaded, and it changes to a sense of stability that does not waver when you put a little weight on it.
Installation is simple and straightforward, but a Torque wrench is required.
In particular, the bolt near the under bracket needs to be tightened behind the crankcase, so if the screw hole is broken by Overtorque, the entire crankcase will have to be replaced. If you are not confident about this, bring the bolt in or ask someone who is familiar with it to do it for you.
Side stands sensors can also be used without modification if the wiring is changed. All Bolts are specified with a specific Torque, so be sure to observe the Torque. This is also stated in the assembly manual.
One regret I have is that the Center Stand interferes with the BackOffset if a Side StandAdapteretc. is installed to increase the installation surface.
This must be addressed with the use of the anti-embedding Platec.
Nevertheless, the product is relatively easy to install and highly effective.
View detail
Fits: HONDA glom, HONDA PCX150, HONDA PCX125, HONDA LEAD125, HONDA DIO110
easy and convenient
It is convenient to start the Engine with the Side Stand out by simply installing it with Couplet-on.
It is a simple but useful product.
View detail
Endurance Right Side Stand
The finish of the bracket and STAND is perfect, and the STANDBOLT nut and springs are Honda OEM parts. The rearward offset makes it difficult to fall over even when the rear box is fully loaded with luggage. I use it with reinforced STANDBracket and it is very useful! View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
Easy
It will be possible to start the Engine with the Side Stand out.
It would be strange if you short-circuit it yourself, but this product is easy to use because all you have to do is to attach it.
It can be easily installed by simply short-circuiting the side stands switch.
View detail
Seems strong for the price.
If the MONKEY has 12inch wheel, 330mmRear suspension, and the Swing Arm is about 20cmLong, it should be about 260m. It is a little too far down, so it is just right to adjust the rest by using a collar.
It's STAND, so even if it's cheap, it's good enough because it's something that will get scratched whether it's of poor quality or not.
View detail
Fits: HONDA C70 A-PASSPORT, HONDA C70/71/72 (DREAM), HONDA CB125S, HONDA CH150 A-ELITE 150, HONDA CH150D AC-ELITE 150 DELUXE, HONDA CT125 A-TRAIL 125 S, HONDA CT70 TRAIL 70, HONDA TLR200, HONDA XL100 A, HONDA XL100S, HONDA XL125, HONDA XL70 A, HONDA XL75, HONDA ZB50 A, HONDA SUPER CUB110PRO, HONDA BENLY50CD90, HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50PRO
With Impact
I put it on my AC09 JAZZ and it was EXACTLY! View detail
In fact, it is resistant to earthquakes.
Crack appeared on the OEM Side Stand, so I replaced it.
In the event of an earthquake, I still prefer the Side Stand, because the Center Stand would fall over.
Replacement is easy:simply stand the Center Stand upright, level the vehicle body, and replace the existing Side Stand.
good point
The ●STAND foot is solid, so we can expect it to be durable.
JAPAN in trust.
The Spring part is also solid.
● Since the replacement, there have been several earthquakes, but no problems at all. Don't forget the single speed and Handlebar Lock.
You don't have to experience it, but if you experience an earthquake, you will think that the Side Stand is effective in preventing your motorcycle from falling over. I had no problem even with an earthquake of intensity 6.
View detail
![[Optional Parts] Replacement Chip](https://global.webike-cdn.net/photo/impression/c2/c20aa15809de3ef9b30b367b472a646bL.jpg)
Mounting on WR 250X
I wanted to shorten the STAND because it was too lowdown and lost its tilt, so I installed this -25mm one.
It was a very good thing with a reassuring inclination.
View detail
Installed on a WR250R
I am using XWheel to make MOTARD, but the OEM length of X is a little too long for my vehicle, so I have replaced it with a +15mm tip.
It's not that much lighter than OEM, but it looks better, so it's a good part.
View detail
CT125 as a fall-back option to CT125.
[How is it used?
When a heavy load (box + tandem, etc.) is placed on the rear carrier, the side stand alone will not allow the front to move up, and the front will not allow the rear to move down.
Introduced as an auxiliary STAND because the vehicle body collapses as it is.
Was the one you received as per Image?
The product is quite gussied up and seems to be stronger than OEMSTAND.
Was the installation difficult?
It is easy to use, as it is just a matter of tightening it to the Tandem Footpeg, but it is not a dedicated product.
Interference countermeasures (Washer, body shaving, etc.) in actual product matching.
Bolt selection appropriate for strength (I use HondaOEM 8*34Socket Bolt 90112MBRJ10)
is required
How was your experience with it?
I am satisfied because the stability has been improved as expected and there is no sign of front up and tipping over even with luggage loaded on it.
Of course, there is no side stands switch, so care must be taken not to leave it out while driving.
[Included Parts:were they on?
It came with Bolt and Washers, but I did not use any of them.
(Washer with brim, Bolt, etc. as described above are prepared separately.)
[Was there anything that disappointed you?
There are considerable spatter marks and the visual quality is not flattering.
It's not a place to look seriously, so I personally don't mind it too much.
View detail
STAND is unreliable (is it any wonder it's SS?)
I bought it because I didn't want to get stuck and cocked when I parked on uneven ground.
If you put it on, you can park anywhere you want.
However, it would be nice if there were more Color variations.
I'd appreciate it if you could also put Spare's Screw on it.
View detail