• Home
  • Product reviews
  • Search reviews
  • Motorcycle Parts
  • Frames / Protections
steps-review.png
Filter
icon-webike.png
Write a review and get Webike Points!

Reviews
Frames / Protections Clear all
Engine Guard
KITACO
Engine Guard

Fits: HONDA GB350, HONDA GB350S

Japanese Webike user
4/5

GB Engine Guard

[How is it used?
24-hour (e.g. observation, operation (of a machine), care (of patient))

Was the one you received as per Image?
high
Was the installation difficult?
Easy
How was your experience with it?
No problem
[Included Parts:were they on?
OK
[Was there anything that disappointed you?
Oil replacement has become a bit more difficult.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail

Pipe Engine Guard
DAYTONA
Pipe Engine Guard

Fits: HONDA CT125

Japanese Webike user
4/5

Great rigidity.

The pipe is thicker and has more fixed bolts than the OEM, so it is very rigid.:It comes with a Plastic Slider, so it will be cheaper in case of moss.
However, installation was a challenge. Since it is slightly gapped, I managed to install it by fine-tuning while loosening and temporarily fastening.
I thought it would take an hour to finish and started working on it at 15:00 and finished at 19:00. I think it was an individual difference.
The product is good and I am satisfied with the Large change. View detail

Accessory Bar
SUZUKI
Accessory Bar

Fits: SUZUKI Gixxer 250

Japanese Webike user
4/5

OK for minor falls

Large sturdy to the extent that it is knocked down when standing or parking.
RearBrake pedalBrake lever and clutch lever will bend if it is knocked over even with this attached.
It does not seem to be able to withstand a fall while driving. View detail

Racing Slider Kit "PRO Shield"
YOSHIMURA
Racing Slider Kit "PRO Shield"

Fits: SUZUKI Hayabusa

Japanese Webike user
4/5

Fallen cannibals

[How is it used?
Purchased considering it as a walking stick before you fall down.

Was the one you received as per Image?
The head part seems to be a bit large, but I guess it is not so when I install it.
Was the installation difficult?
Although a pattern was included when drilling mounting holes in the Sub cowl, it was difficult to align the holes, so it might be better to ask a contractor to drill the holes only.
[Included Parts:were they on?
The metronome was included with the installation instruction manual, pattern paper, etc. I copied the pattern paper in advance and used it.
[Was there anything that disappointed you?
The accuracy of the pattern may not be good enough. View detail

Short Side Stand
ARCHI
Short Side Stand

Fits: KAWASAKI ZX-25R

Japanese Webike user
4/5

too long a delivery time

It took more than half a year to receive my order. It seems to be a Taiwanese manufacturer, but even so, the delivery time is too long. The paint is too thick on the shaft screws and frame engagement area, so it does not move smoothly even after installation. The grounding part is the same shape as OEM, so there is no problem with stability.
When removing the Spring, you will have no trouble if you pull out the Bolt first and then remove the Spring. 。 *No instruction manual of any kind. View detail

Frame Slider
BABYFACE
Frame Slider

Fits: KAWASAKI Ninja 1000 (Z1000SX)

Japanese Webike user
4/5

Body installation itself is easy

Since I bought a used NINJA1000 without a slider, I installed a slider to reduce wounds when falling down.
Removing the cowl is a bit of a hassle, but once removed, it was very easy to install the base plate and the slider cone. However, the M8 Cap Bolt that holds the slider cone in place may loosen easily, so the use of a screw locker is recommended.
It was inexpensive compared to otherManufacturers and the installation diagram in the Instruction Manual was easy to understand.
Two Logo stickers were included. View detail

Performance Damper (R)
ACTIVE
Performance Damper (R)

Fits: HONDA REBEL250, HONDA REBEL250S EDITION, HONDA CL250

Japanese Webike user
4/5

Mounted on HondaCL250

When not installed, I tried driving on the New Tokyo Highway at over 100 km/h. The vibration was so strong that I thought the car body might break. The vibration was so strong that we thought the car body might break, so we gave up flying because we felt sorry for the motorcycle. After that, we installed this product and drove on the same route. Although the vibration was not zero, I was able to run at 120km/h in a stable manner. I can bank the car on the mountain pass without any worries, and I can drive at a higher pace than before with a good feeling. This is just an amateur opinion! (Lol) View detail

Frame SliderPro 2.0 (FRAME SLIDERS)
Puig
Frame SliderPro 2.0 (FRAME SLIDERS)

Fits: HONDA XL750 TRANSALP

Japanese Webike user
4/5

It was not as noticeable as I thought it would be.

I was looking for a Slider on the Engine side and installed it after standing on it once, I thought it would be up to the Guard pipe, but the actual Slider is not very noticeable and seems to work in case of an emergency.
I used WeBigPit InService for the installation, but it looked Larger than I expected and it was impossible to do it by myself. It was the right choice. View detail

Performance Damper
ACTIVE
Performance Damper

Fits: SUZUKI SV650X, SUZUKI SV650

Japanese Webike user
4/5

Handlebar vibration reduction

[How is it used?
Commuting and Touring.

Was the one you received as per Image?
Both the packaging and body were better than I had imagined, with a higher quality.

Was the installation difficult?
The manual is very thorough, so there are no problems. General tools are sufficient, but it might be better to use a Torque wrench since the Bolt and Nut are described as Torque in various places. (20N-m to 90N-m)
I did not know the jack-up point for replacing the shaft of the engine mount, so I jacked it up at the appropriate point, but the shaft itself came off without any trouble, so I felt that I did not need to jack up the shaft. (There are descriptions of applying jacks to the Exhaust System, Oil Filter, etc.)
The replacement itself takes about 30 to 40 minutes, and the difficulty level is about normal for those who are familiar with maintenance. However, if you do not have a torque wrench or jack, or if you are not confident about loosening the engine mount, it may be safer to take the engine to a shop.

How was your experience with it?
Vibration was dramatically reduced and the effect was easy to see.
The flopping sensation is reduced and the car feels sturdier, even on rough roads and continuous gapping.
However, I think that the vibration damping on the Frame side plays the role of Large Kinashiro, and there was no change in the impact when passing through the Large Kinashiro Gap.

[Included Parts:were they on?
Complete set shown in the product photo (Clamp, shaft, bolt nuts, etc.), Owner's Manual (Installation Instruction Manual)

[Was there anything that disappointed you?
I am generally satisfied with MinusPoint, but the price is a little over 40,000 yen (+α labor cost), so I am not sure if I would recommend it to everyone in terms of cost-effectiveness. I recommended it to my acquaintances, but they did not respond well. My impression may change depending on the level of dissatisfaction with the vibration of my car. (I don't think the vibration of sv650 is that large, but I am satisfied with it because I am of the opinion that there is nothing better than having no vibration). View detail

Engine Protector
DAYTONA
Engine Protector

Fits: HONDA CB1100, HONDA CB1100 RS, HONDA CB1300SB, HONDA CB1300SF, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP

Japanese Webike user
4/5

General Slider

The car was delivered with DAYTONA's Engine Guard installed.
Because I scraped it just by driving normally on a mountain road,
Changed to Slider.
I am concerned about Damage to the Motorcycle in the event of a fall. View detail

Engine Guard
HEPCO&BECKER
Engine Guard

Fits: SUZUKI V-Strom650 L2, SUZUKI V-Strom650, SUZUKI V-Strom650 XT, SUZUKI DL650 V-Strom, SUZUKI V-Strom650 L2 XT

Japanese Webike user
4/5

Engine Guard installed

Installation should not be a problem if you have some knowledge of maintenance.

An Engine Guard was added to protect the engine in the event of a runaway and to mount the Fog Lamp. View detail

Sub Frame Kit
OVER RACING
Sub Frame Kit

Fits: KAWASAKI Z650RS

Japanese Webike user
4/5

Looks GOOD??

It looks GOOD.
I think it is stronger than without it, but I don't know.
The price is a little high. View detail

Engine Guard
World Walk
Engine Guard

Fits: KAWASAKI ELIMINATOR 400, KAWASAKI ELIMINATOR 400 SE

Moto USA
4/5

No instruction manual included

There is no instruction manual. The collar and bolt are confusing, or rather, wrong. The "right side, left side" in the product description photo is "right side, left side" from front to back. The 150mm bolt and 68mm total collar are installed on the left side of the vehicle. The 115mm bolt and 33mm total bolt are on the right side of the vehicle. The tightening torque is 35 ft.lb. It was able to be installed properly on the American specification 451cc Eliminator. There is no instructions come with it. 150mm bolt and 68mm (55mm + 13mm) collar are for the left side. 115mm bolt and 33mm (20mm + 13mm) collar are for the right side. Tightening torque is 35 ft.lb. They fit Eliminator 450 and 500 too. Enjoy! View detail

Skid Plate
ACERBIS
Skid Plate

Fits: HONDA CRF250L

NO NAME
4/5

Works like a skid plate should

Installation will require only 5mm bolt. Color match is wonderful for bike. Immediately took this to a local trail to test it out and managed to slam it on some rocks. Held up great, took a bit of damage but that's what it's for! Its tough but it's still plastic so I'm sure it has its limits.something to protect the finish on the frame and keep the mud off the motor.Little to no gaps, excellent coverage of major components.You will need to remove this skid plate when you change your oil.But if you are a little lazy about your oil changes, this may not be for you.This is the perfect solution and was reasonably priced. View detail

Frame Slider
SSK
Frame Slider

Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000

Japanese Webike user
4/5

I think it's a little too Large.

The Cowl is easy to install because there is no modification, it is cheap to work with, and it is very helpful for the Large size change. View detail

Sub Frame Kit
OVER RACING
Sub Frame Kit

Fits: KAWASAKI Z900RS Cafe, KAWASAKI Z900RS

Japanese Webike user
4/5

Custom look

It is recommended to install at the same time as the engine slider.
How does it improve the performance of the Motorcycle? But this alone will give you a great sense of customization. View detail

Engine Slider
OVER RACING
Engine Slider

Fits: KAWASAKI Z900RS, KAWASAKI Z900RS Cafe

Japanese Webike user
4/5

Fallen cannibals

The system was installed to reduce damage to the vehicle body and engine in the event of a standing accident or a fall.
It gives a sense of overhang and security. View detail

Performance Damper (R)
ACTIVE
Performance Damper (R)

Fits: KAWASAKI Ninja400, KAWASAKI Ninja250

Japanese Webike user
4/5

It certainly works.

Looking at the frame structure of the NINJA2 Helmet 50/400, it seems to me that the Left Side conectoplate is intentionally made weaker by bending it. It is my imagination, but it may be that the torsion of the frame improves mobility. The claim is that the Damper will absorb vibration and provide straight-line stability by restricting the movement here.
As it was, the ride quality was not good, so I weakened the front and rear Suspension settings by about 2Click, which I think improved the driving stability without worsening the ride quality.
I am a dull person who cannot tell the difference with a slight change, but I can certainly feel the change. It may be too much to say that the driving has become more luxurious, but I feel a sense of stability.
I am tuning the front and rear suspension with Technics or NITRON, but if you put it on a vehicle with Normal suspension, I think the original uncomfortable ride and thrust will be emphasized. However, if you use NINJA2 Helmet 50/400, it may be good for those who don't feel bad ride quality. View detail

Rear Shock Slider
K-FACTORY
Rear Shock Slider

Fits: HONDA CB1100, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA X-4

NO NAME
4/5

K-Factory rear shock slider

Ok so I was expecting the slider to be bigger than it was so not sure it will offer much protection,I can say that the product is well made and looks nice when fitted View detail

[IDEAL] Swingarm Stand Hook
BABYFACE
[IDEAL] Swingarm Stand Hook

Fits: Others , KTM 1190 RC8R, KTM 1190 RC8, HONDA CBR954RR, HONDA CBR929RR, HONDA CBR1000RR, HONDA CBR1000RR-R, HONDA CBR1000RR-R SP, HONDA VTR1000 SP1, HONDA VTR1000 SP2

Japanese Webike user
4/5

Casual Dress-up

For Front Axle Slider and Engine slider
I have Babyface on and a Stand Hook.
The same Manufacturer is used for this product. View detail