Reviews
Fits: HONDA ADV160, HONDA PCX e:HEV, HONDA ADV150, HONDA PCX160, HONDA PCX160, HONDA PCX, HONDA PCX
The construction is good.
Material:Stainless Steel and well made.
However, I think that about 4,000 yen is appropriate at the highest.
Instruction Manual is also paperless and not included.
View detail
GALE SPEED's Radipon's TankNipple's Angle conversion
The GALE SPEED radipon only comes with a TankNipple with Straight and no 90-degrees in Option, though,
for Rear with Angle can be fitted with this AngleNipple.
They are sold in the supplemental parts and can be ordered.
I wrote it here because I can't do imprints on ordered products.
Well, they are essentially the same thing, right?
The Snap ring can be installed, but the Rib part is slightly thinner than the Nipple for Front, so the Snap ring will rotate round and round if the Rib is left as it is. (No exclusions will be made) 。
I have not tried it, but it seems that substituting Nipple for Front for Rear is not possible.
If the O-ring is not old, it is Large sturdy, but you are on your own if you install it.
Hose is normal! Hose clamp is included. The inside diameter is not clear, but it is for brembo etc...
View detail
Fits: KAWASAKI D Tracker 125
Even though the car model Bolt On.
I bought it because it is Bolt On for my car model.
Caliper's Screw is covered by Caliper's Screw.
I can't remove the Caliper Adapter.
I think Straight is a good choice.
View detail
It's all right.
I don't think there is any problem to use it, but the Adapter and the color of Hose are the same Manufacturer.
It's somewhat frustrating that it doesn't fit.
View detail
Fits: HONDA C125SUPER CUB, KAWASAKI Z125PRO, KAWASAKI Z125PRO, HONDA SUPER CUB
First Red Pad with regular replacement.
Due to pad wear, the OEM Pad is replaced with a DAYTONARed Pad.
I used Golden Pad before, but this is my first time to use Red Pad because I felt like there was a lot of Damage in Rotor.
I don't know about wear resistance yet, but I feel that braking power is slightly increased over OEM.
I prefer this to the more intense effect.
Now we have to see how the wear resistance and aggressiveness to Rotor will be.
View detail
Not enough for use in Circuit
I replaced it with Gicu Ceramic sintered at the same time and used it on Circuit, and Judder appeared at full break in about 5 minutes after break in.
I don't know if it was incompatible with the Pad, but I was too scared to hold the Brake.
Then I switched to OEMPad and it was almost a non-issue.
However, since the thickness is 4mm, we decided to replace it with a 5.5mm one, considering the future endurance race and other factors.
View detail
Available for frando 7nb
Available for frando 7nb MechanicalSwitch, which has the same structure as brembo.
I believe only frando 7nb is available as a precaution.
The reason is that the current frando's Lineup has changed the SizeSetc.Spec. of the Pipod degree.
Also note that this is not an official usage.
View detail
![Brake Pad - Scooter [XS] Compound](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0320/25640972_20221222144825767_TS.jpg)
Fits: SUZUKI BURGMAN400, SUZUKI BURGMAN400, SUZUKI SKYWAVE650 burgman, SUZUKI SKYWAVE650 burgman, SUZUKI SKYWAVE400 burgman, SUZUKI SKYWAVE250 burgman, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman TypeM, SUZUKI SKYWAVE250 burgman SS, SUZUKI GEMMA
not yet
I have not used it yet. I bought it for Stock. I bought brembo's Sintered, but it looks the same as SBS's Sintered. If it runs out after 3000 km, it will be the same. View detail
![Brake Pad - ROAD [CC] Compound](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0320/25640971_20221223092751779_TS.jpg)
Fits: SUZUKI BURGMAN400, SUZUKI BURGMAN400, SUZUKI SKYWAVE650 burgman, SUZUKI SKYWAVE650 burgman, SUZUKI SKYWAVE400 burgman, SUZUKI SKYWAVE250 burgman, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman TypeM, SUZUKI SKYWAVE250 burgman SS, SUZUKI GEMMA
not yet
Not used yet Purchased for Stock View detail
Fits: YAMAHA WR250R, YAMAHA WR250F, SUZUKI RMX450Z, SUZUKI RM-Z450, SUZUKI RM-Z250, KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX250, YAMAHA WR250X, YAMAHA WR450F, YAMAHA YZ125, YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA YZ450F, KAWASAKI KX250, KAWASAKI KX250F, KAWASAKI KX450F, SUZUKI RM-Z250, SUZUKI RM-Z450
Purchased for Replacement because it was worn out.
Replaced with a Red Pad that worked well for the price because it was worn out.
I don't drive off-road anymore, so this is enough for city driving and touring main.
It works very well, but the durability is not so good and I think it is too early every time.
View detail
Fits: YAMAHA Majesty 250SV, YAMAHA Majesty., YAMAHA Majesty C, YAMAHA Bronco., YAMAHA Serow 225WE, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA XT250X, YAMAHA TW225, YAMAHA TW200, YAMAHA TRICKER, YAMAHA TRICKER S, YAMAHA SEROW, YAMAHA SEROW250S, YAMAHA RZ50, YAMAHA MAJESTYC, YAMAHA MAJESTY 250SV, YAMAHA MAJESTY, YAMAHA BRONCO, YAMAHA MAJESTY 250SV
Used in Caliper for RZ50
We chose the cheapest one because it is used for city driving and touring.
The durability is not bad, and I would buy it again.
View detail
Fits: YAMAHA NMAX, YAMAHA NMAX, YAMAHA NMAX155, YAMAHA NMAX(125), YAMAHA NMAX155, YAMAHA NMAX155, YAMAHA NMAX155
Reliable quality that has remained unchanged for a long time.
I have been using Pad for a long time and it does not disappoint.
IRC Tire's pad is a little more reliable than the OEM pad.
However, it still decreases quickly. It depends on how you drive.
View detail
![[NISSIN Repair Parts for Caliper] Caliper Mount Bolt](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0154/533808_1_TS.jpg)
Fixing Screw
It is used for the Fixing Screw of the Brembo caliper section.
It was not easy to purchase this Size and length to fit, so I was able to buy it nearby.
View detail
It's a bit expensive
Purchased for replacement with bremboRCS.
Cospa is not good.
More than that, I would have liked a little more flexibility in Bracket.
It will look and feel different, though.
View detail
Fits: Others , Others , Others , Others , Others , Others , Others , Others , Others
Used for frando 7nb
We used the same shape as brembo for frando 7nb.
The following three products, including this product, can be used for MechanicalSwitch conversion.
We chose Gold for the Accent this time, but Black products are also available.
https://www.webike.net/sd/21995643/
Ladybird Ladybird:LBP-BS1000
Mechanical Type Brake Switch
https://www.webike.net/sd/21216231/
KOHKEN KOHKEN:KOK-2031TI
Push Rod Pivot Brembo Radial Master
https://www.webike.net/sd/21216233/
KOHKEN KOHKEN:KOK-2030TI
Lever Pivot Brembo Radial Master
View detail
When installing bremboCaliper
Installed when bremboCaliper was installed.
I had the color I wanted and the installation was completed without difficulty.
We will see about durability in the future.
View detail
Attached to Koken's Clutch holder!
This is attached to a Mechanical Clutch Holder from KOKEN. I tried it because I read in the product description of Koken that this can be attached to a mechanical clutch holder! I tried it because it was written in the product description of Koken.
By allowing for a design that is closer to that of the already installed RCSBrake master, the Quantity:Pair (for Left and Right) I am happy to take Balance in the
It is quite plain, but highly self-satisfying.
View detail
The fact that you can only choose the color Red is fatal, isn't it?
For MC51 CBR250RR, the only color choice for inner rotor is Red. I was told by a staff member at SUNSTAR that there was a color custom order in the past, but they do not do it now.
My body was White and Blue, so a Reddish Rotor is out of the question. But SUNSTAR is the best design. What should I do? I decided to have it anodized by Koken, or paint it to match the wheel collars, the latter was my choice.
The new Rotor was disassembled and painted by having the plate Gold craftsman tone the color to match the color of the Wheel. The result was just like the Image, so I am Large satisfied.
View detail
Installation is Large
It took a total of 5 hours and I would not recommend a beginner to operate it on their own, the BoltDesign on the Caliper side was poor and very difficult to tighten, there was no obvious change in the feel of the Brake, the only difference was that the Brake was very tight, the Caliper side was very tight and the Caliper side was very tight. View detail
Hmmm...
It's not too bad, but I'm a little disappointed that it's not interchangeable with other companies' products.
The company's colors are a little light and don't match the colors of the Hose, which is a little frustrating.
View detail