Reviews
Easy to install!
Installation was easy.
Japanese Vehicle Inspection Correspondence, but I think the sound is too loud.
But it's cool, so I'm satisfied.
View detail
Fits: HONDA XL250S L250S, HONDA NY50 All models, HONDA CROSSCUB110 JA10, HONDA All models of GIORNO CREA AF54, HONDA SUPER CUB 110 JA10, HONDA SUPER CUB 110 PRO JA10, HONDA SUPER CUB series Engine cars (50-100cc), HONDA SUPER CUB series Engine car FI, HONDA Spacy50 All models, HONDA DREAM50 AC15, HONDA Spacy80 All models, HONDA VARIE All models, HONDA MONKEY series Engine cars (50-100cc), HONDA MONKEY series Engine car FI
Very common EXGaskett
CROSSCUB110 (JA45) Used to replace the Exhaust System of
I think Gasket is the same for all Manufacturers.
No exhaust leak etc.
It was cheaper than OEM Parts.
View detail
Fits: KAWASAKI ZXR250, KAWASAKI KLX125, KAWASAKI D Tracker 125, KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ELIMINATOR 250V, KAWASAKI ZXR250R
KLX125
KLX125
DrumstickDrumstick fits!
View detail
Fits: HONDA glom
You can experience the effect!
The details are carefully crafted.
The replacement process was relatively easy and quick.
The Torque feeling at startup will be a little thinner.
The Engine turns pleasantly after running and is solid and powerful.
However, although the sound quality is good, it might be better if the volume were a little louder in the smallest volume so that the driver would not have to worry about it when driving around town.
Also, there was a Gasket LINK on the page where I purchased the product, so I bought it together, but it was for Full Exhaust System.
I wish it had been mentioned on the product page that a joint gasket is required for the Slip-on Silencer.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
light
[How is it used?
After installation, the car traveled about 200 km.
Was the installation difficult?
It is not so difficult to install except for the Flange, which is a type of two-piece flange, so it is difficult to install unless you get under the motorcycle.
How was your experience with it?
The OEM one is quieter, both idling and running, but the OEM one is louder. Personally, I was satisfied with the quietness, as it was just right for me. The sound quality is not as harsh as the OEM, but low and smooth.
Lightness is somewhat felt when pushing and pulling.
[Was there anything that disappointed you?
There are too many springs to install, but since spring hooks (devices) are not included, it is better to prepare them.
[Others]
Point or hang for installation...nothing special. If you dare to say so, there is no need to twist the O2 Sensor when installing it. If you install the O2 Sensor lightly before fixing the middle Pipe and turn the Pipe side around, you don't have to worry about the O2 Sensor wiring twist.
Availability and clarity of Instruction Manual - I can understand without it.
Items to buy together...Gasket is a good thing to have. The only other thing I need is heat resistant grease.
【Review】
Personally, I don't like the length of the exhaust end, the degree of raising, and the color (I prefer shorter, lower, and Polished Titaniumium), but I am very satisfied with the lightness, the Hand Bent-like curve of the exhaust pipe, and the high quality sound.
View detail
Easy to install
To begin with, I bought it for replacement for an OEM that looks rusted and battered.
The product itself can be installed without any difficulty, but I tried to replace the stud bolt because it was a good opportunity,
It still broke and Shop took care of it.
I am happy with the way it looks and the way it is attached to my car.
The most important thing is the effect, but I have run about 30 km and I don't feel it….
When you say it, it is like a smooth Speed ride.
Scattered bells could not be heard.
This time, I am satisfied because the appearance is important to me.
View detail
Fits: HONDA GROM
nice sound
I feel that the sound changes from about 6000 rpm, and it is a nice sound that keeps me turning.
However, after one week and about 200km, discoloration and rust started to float, so I recommend applying StainlessGuard if you are concerned about it.
View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R SP
It's easy
Heat Guard installed, took me a while to figure it out because of the orientation of the Band. Please see the pictures. View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R SP
The contents are unknown, so I will Up.
I purchased the carbon heat guard because I needed it.
[Contents] but since it is unknown, I will provide a photo of it before installation.
1.Band Quantity:2pc. Set
2.Bracket Quantity:2pc. Set
3.Bolt Quantity:2pc. Set
4.RubberWasher 4 pcs.
5.Carbon heat guardBody
6.Instruction Manual for English Version
This band can be installed with the Exhaust System installed.
Therefore, the exhaust system will not be pulled out during the process of installing the Heat Guard.
The band is fully loosened and threaded through the bracket.
The rest of the time, Heat Guard is used with Bolt and RubberWasher.
Tighten.
CBR1000RR-R with Slip-on lineTruck di
So, I will install this product.
View detail
Normal look is the best
The bolt of the normal heat guard, especially the heat guard attached to the Exhaust System, is quite large.
It was tightened by Overtorque.
The cap bolt included in the package was a little short, so I procured an M8-45 at a hardware store.
As mentioned in the instruction manual, the Heat GuardBracket needed to be adjusted while making the actual adjustments.
It is good for those who like Normal look.
The silencer end changes the appearance of the silencer.
Sound has also changed to a thicker overall look and feel and I am satisfied.
View detail
Fits: HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO
Design good.
The OEMExhaust System is pretty quiet, so I went with this one, which is cheaper and looks better.
Simple design in Stainless Steel is good.
Sound is quieter than I expected, although Punch is there.
I am glad I bought it because it is quiet and I don't have to worry about my neighbors.
View detail
Fits: YAMAHA BWS100, YAMAHA GRAND AXIS, YAMAHA JOG90, YAMAHA AXIS 90, YAMAHA Horizontal TypeEngine2Cycle50cc series, Others
Mufflet protector type 2
Good product and easy to install..item come with good packaging and safety..order two for my bws100..will order with webike soon View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000
Truly YOSHIMURA
I installed it on a 2015 NINJA 1000.
Installation went fine.
The sound is not so different from NORMAL? It is not so different from NORMAL.
The handling is no different.
The appearance has changed considerably.
I like it very much
View detail
Do not have excessive expectations for volume and sound quality as it is Japan Government Certificated.
We had been proceeding with customization on the premise that the engine would be large enough to be able to enter Kawasaki Plaza after it became a Kawasaki Care Model, and the engine type would be changed to comply with the exhaust gas regulations, and we were waiting patiently for the release of the Japanese Government Approved Exhaust System. I was waiting patiently for the release of the Japanese Government Approved Exhaust System, but Trickster was the first to start the development and release, so I purchased it as soon as I could place an order on Webike and I was looking forward to the delivery.
The color is available in Yaki Titanium and Black edition, but since the OEM is in Black, I felt that the replacement of the black color would not look as good as it did at first glance, and I thought that the Yaki color would match the 40th anniversary model. We chose Titanium because we felt that the OEM's black color would make it look less like a replacement.
The Gasket used is OEM and enclosed is also OEM. If there is a need for replacement in the future, it will be easy to obtain.
The instruction manual is as simple as removing the OEM and attaching the Trickster's, and that is correct, but it does not mention anything about removing the exhaust device cable, which is necessary to remove the OEMSilencer. I think it would be a good idea to learn how to remove the cable beforehand, as there are many YouTube videos on how to do so.
Also, the torque for tightening bolts is not listed.
The instruction manual for YOSHIMURA's Slip-on Silencer in the previous car mentioned Torque tightening, so I felt that it would be better to improve that area.
Certificate of Exhaust Gas Testing is also included.
Installation can be done without difficulty by following the instructions as long as you have a 10mm or 13mm box, a Glasses wrench, and a spring hook.
I am using an external (WoodStock) exhaust bracket, which is compatible with the OEM exhaust system, so I was able to install the silencer band without any problems.
When I started the engine after the replacement, I found that the sound quality of the Japanese Government Approved Exhaust System was better than that of the Idling Exhaust System, and I felt that some bass sound was added. However, there was almost no change in volume.
After a short test run in town and turning it as far as possible, I did not notice much change in both volume and sound quality through the Helmet.
Also, I did not feel any clear change in driving performance.
I will re-review this area if I notice anything after driving on the mountain passes and Touring.
As the weight of Trickster's Slip-on Silencer was not listed, we inquired with the manufacturer and were told that the weight was 2.2 kg.
The OEM exhaust system weighs 5kg, and the servo motor, which was removed in conjunction with the OEM exhaust system, weighs 0.5kg, resulting in a weight reduction of 3.3kg.
From a design point of view, when installed on the car body, especially on the 40th anniversary model, the connection between the blue part of the Seat Cowl and the exit baking color is good, as originally intended, and the synergistic effect makes it look even cooler.
However, when weighing the satisfaction of the light weight & appearance against the dissatisfaction of the little change in volume and sound quality...
I think it is better not to expect too much from the Japanese Government Approved Exhaust System, so I feel that whether or not you can afford this price as one of the dress-up parts is a criterion for judgment. I think it would be better to consider this carefully.
View detail
Cospa.
Very easy to install, even Spring was hooked up by pulling with fingers. (Large sturdy?)
The silencer is mounted with a single bolt, but there is no spring washer, only a flange nut with serration. Is this to prevent the angle from changing? It seems to be to prevent the angle from changing.
It looks good. The angle of installation can be changed.
Sound is Idling and 4,000 rpm is thick and powerful.
Unfortunately, the rest of the sound is drowned out by the intake and Engine noise.
It sounds good from the outside, but I don't hear it.
Still, the sound pressure is felt considerably more than with the OEMSilencer.
Power is slightly better, I think Response is better.
I have not been able to rev the engine to high rpm yet, but the more I rev it, the louder the engine noise becomes, and I don't think I can hear the exhaust system noise.
Will it be quieter after break-in (as Glass Wool settles in)? Or will it Sound better?
I'm looking forward to it.
View detail
The thing with DURACON on the end!
I forced myself to put it on a VSTROM250SX!
The attached Screw does not fit, please refer to the second photo.
Installed better than expected, just fit!
View detail
Fits: KAWASAKI Z900RS Cafe, KAWASAKI Z900RS
Good browning of Exhaust pipe
Neck is a bit expensive because of Titaniumium full exhaust.
Other than that, no complaints.
There are two catalysts in the middle of the pipe, so if you want to make the sound more loud, you can remove them.
I am enjoying it at a decent volume with both places removed.
View detail
It looks cool!
I changed from the OEM Exhaust Cover and am happy with the improved look.
No modification is required, and the Bolt can be used for OEM applications.
Recommended if you are buying for looks and not expecting weight savings.
However, I think the price is a little high for this ….
View detail
Fits: HONDA CT125, BMW G310R, HONDA MONKEY125, HONDA Cross Cub110, YAMAHA XMAX
Looks good, Parenthesis good, good to have ?????
I would run without it, but I would definitely burn myself without it. When I test drove with it on, the calf of my right leg was constantly hitting it.
I think it is made of Dry Carbon, but the price is too high compared to Exhaust System, I thought it would be better to use Wet Carbon to keep the price down.
View detail
Loved this one.
Climbing a hill in my neighborhood after replacing the Exhaust System; accelerates one gear higher than OEM (by feel). View detail