Reviews
Yamaha tappet adjuster 3mm
Original YGP. Fast shipping 3 days from mailed date to Singapore . Package bubble wrapped to ensure no priduct damage during shipping. View detail
Perfect for the hot season!
Was the one you received as per Image?
Purchased for summer work. I like that the fabric is thin and cool, just as I expected.
The color looks close to White in the photo, but in reality it is exactly as shown. Light gray It is
[How did you feel about the Fit?
I am 170cm tall and 60kg and the size M fits me perfectly.
How was your experience with it?
I chose the one without YAMAHALogo, but it is still a good parenthesis.
[Was there anything that disappointed you?
Is the price a little high for work clothes?
View detail
Only special tools can do this.
In order to revive the immobilized YamahaRZ350, I set out to overhaul it, but the Pulley remover I had on hand was not enough to get the job done. I knew the power of the special tool from my previous experience of removing a bicycle without a co-sauce, so I searched for it and found this YamahaOEM tool at a reasonable price. The feeling is that there is no rattling, and I can put a lot of power into it. However, it didn't shake, probably because it was an old motorcycle, so I applied more force with the Expander and was able to remove it safely. There was no sign of overworking the tool, and I am glad I purchased it. View detail
Must needed tool when removing the TW Flywheel
bought this OEM bolt when I needed to do work on my tdub engine.TDUB ,The flywheel is mounted onto the tapered end of the crankshaft. It is secured from rotating with a Woodruff key, and is tightened down by a bolt that threads into the end of the crankshaft. To remove the flywheel, you must first remove this bolt, The next step is to thread a bolt ( THAT'S WHAT THIS OEM BOLT ABOUT ,CALLED OEM ROTOR PULLER OR FLYWHEEL PULLER) into the internal threads of the flywheel.The TW's rear axle is the correct thread and can be use to do this also BUT I don't want to take any risk and buy a YAMAHA OEM BOLT ,THAT DESIGN TO DO THE JOB WITHOUT HESITATION.As this bolt is tightened, the flywheel will be pulled free from the tapered crankshaft. All threads are standard right hand threads . Then secure the flywheel from turning and then try to remove the Flywheel bolt first Then you should be able to use a proper sized bolt/flywheel puller to get the the flywheel to pop free. The proper thread size needed is 16mm x 1.5 RH . as usual package received very quickly after dispatch from japan. quality packaging and quality service .thank you WEBIKE. Highly Recommend Online shop. 5Star View detail
I made a mistake.
I mistakenly imprinted a different product.
WY-208 does not come with Fleece
Sorry for the Large change.
View detail
I can't wear anything else anymore.
Worn when repairing Motorcycle.
I am 167cm 70kg, chest 100cm. I usually wear LL jackets, but the Leather suit dragged on my legs, so I went with the L. It is a little tight in the chest. It is a little tight in the chest. When I bend down, my neck hits the collar.
The inside is a yellow-colored fleece; the fleece cannot be removed.
It is warmer than a cotton-only leather suit in cold weather. It is even warmer when you wear a heat-generating long T-shirt.
When test riding a repaired motorcycle in winter, the lower half of the body gets cold even when wearing a jacket, but this Leather suit is Large and sturdy.
There is no back print of Manufacturer's name.
It is a luxury fabric and I work with care when doing oil work. It looks like a leather suit worn by the ChiefMechanic of a luxury car dealer.
I can't wear anything else for winter work anymore.
View detail
Great
Great exactly what I need for fjr. It smells like an old item but its well oiled & kept. Parcel came in very well packed too though delivery took some time. View detail
YAMAHA OEM Tappet Adjuster
I used to use wood screw for valve adjustment job in the past.This OEM tappet adjuster tool quality seems suitable for light work that it will see in a DIY .The square swivel does fit.I can use this tappet adjuster tool to adjust the valves on my yamaha TW200 motorcycle .this is by far theSl.The square drive fits perfectly.TW200 VALVES TICKING NOIZE LITTLE LOUDER THAN THE OTHER BIKES.The main purpose of tappet clearance is to allow a small expansion gap of the valve stem and pushrods to accommodate the effects of a heated engine.Using this handy tool can loosen or tighten the valve adjustment screw while holding the lock nut.I would say ,Very much needed tool.I should have buy this tappet adjuster tool earlier.Price is very reasonable and cheap.I'm very glad to have this tool.As usual package arrive on time.High Quality Packaging and Service.Thank You Webike.The best online Shop.I highly Recommended View detail
OEMs are sure.
Since it is an OEM, I don't think this is the best way to go about it.
I don't know until I need to be concerned about OEMs.
View detail
Yamaha Multimeter
Product well received, package was bubble wrapped delivery was fast. Highly recommended to buy. Tested Multimeter in good working order. View detail
Easy to use
Used for double-sided tape replacement of electrical components, etc.
The adhesive strength is good and the quality is fine as it is made by 3M, which is a reliable company.
View detail
Good
The performance is very good and easy to use Tape.
It is easy to use because it is not sticky even when used in areas that get hot from heat.
The price is rather expensive, but it is definitely easier to use than cheap Vinyl Tape.
View detail
Per Tank Cover installation
Uses 3M double-sided tape, which has an established reputation.
In this temperature, it sticks strongly.
Last week, I was using ButylTape.
It didn't stick at all, so I tried again with 3M.
I wasn't sure if I should go with the high tuck or the low tuck.
I don't really see the difference (laughs).
This time, I put it on the lower part of the tank and the
Halfway up the front side of the tank cap hole.
The ceiling area from the front to the tank cap hole.
After the helicopter is mounted, it has a knee grip for a while (laughs).
The Cap hole was held in place with a TankMount Bracket from RamMount.
The ceiling part was naturally attached when I pressed the Cap hole.
The helicopter is now fully attached. And the ceiling.
The Cap hole was floating, so I'm holding it down, but we'll see.
It is, after all, powerful. I'm glad I used it.
View detail
As expected, OEM Product
[How is it used?
TZr250R (3XV) I used it to remove the Flywheel from the generator in
There are cheaper MagnetPullers made in China, but I chose this product because it is an OEM Product, which is mentioned in the service manual.
Was the one you received as per Image?
As you can see in the picture, it came in a bag that looks like an automotive tool bag.
I would have preferred a box because I'm sure it will sleep in the toolbox for a while after one use, but oh well, it doesn't matter to the function.
How was your experience with it?
TZr250R (3XV) I used it after removing the Nut from the Center, following the service manual for
When I turned it with MONKEY Wrench and Glasses Wrench as shown in the picture, I was able to loosen it quickly. That's OEM Product.
I think that the frequency of use is not a lot, but if it is this easy to use for less than 2,000 yen, it is good.
[Points to note]
The Handlebar that comes with it will probably be too much for this part as it requires a good amount of Torque.
If you are a person who roses Engine, I think you have Glasses Wrench, so it is safe to work with it.
How did it compare to other products?
Although I did not compare directly, I thought a little whether I would use MagnetPuller of unknown Chinese Manufacturer.
However, I decided to go with the OEM Product, which was the right decision, because the Chinese products in these tools have a lot of "hagap".
【Review】
I was able to remove the Flywheel from the generator in just a few minutes for the first time.
If you want to work with ease, choose an OEM Product.
View detail
MOTORCYCLE TOOL
Hello, I am very satisfied with the product, very fast shipping, very good communication, order tracking,
I thank you for this service, cordially Mrs BROQUET ---------------------------------------- ---------------- Hello, I am very satisfied, the product, very fast, very good communication, order follow-up,
Thank you for this benefit, Regards Mrs GROQUET
View detail
It's easy to use!
1KT (TZr250) I used it in the I used the Universal Product one before, but it didn't come off well and the tool lost, so I bought the OEM Product. It was easy to use and came off easily with the OEM tool. View detail
OEMMagnet Puller
It's an OEM tool and I had no problems working with it. View detail
OEM tools for peace of mind
OEM tool with low price and reliable.
There is a similar tool made in C country, but the price is not so different and the reliability is much different, so there is no Merit to challenge.
I think it's a safe choice as long as you don't make a mistake about the type of car it fits and how to use it.
View detail
YAMAHA OEM Steering Nut Wrench
YAMAHA OEM steering nut wrench. I bought a key for the steering gear in YAMAHA YZF R1 RN12 05 from you. The key for the steering gear helps me a lot. Repeatedly disassembled the steering gear, so as not to rip off the edges in the nut, I clamp everything with a key for the steering gear. It is made of high quality material. I clamp the steering gear with a dinanometric wrench. View detail
OEM tools, after all
I used to use a cheap cross-type universal puller from CHINA
I couldn't get the Flywheel out of the Universal Puller, so I had to try it out I bought the OEM tool and it came off easily
It is easy to apply force because it can be held in the mouth by a large tool
I wasted a lot of time worrying about not being able to take it
View detail