Reviews
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
When connecting the Battery terminal
When connecting to the Battery terminal, it is recommended to use round terminals instead of Y-type terminals.
Not sure if Plating in Gold color is required or not.
Electric Works Pliers are required when Cable is connected.
View detail
Economical for repeated use
Economical as it can be used repeatedly by replacing the batteries without expiration date
Magnet is included in the bottom of the body, so it can be attached to the Gold part of the body.
I think it is a good idea to have it along with PurpleSaver.
It conforms to MLIT safety standards, so it is safe to carry in a car.
The +− notation on the dry cell batteries is difficult to read.
View detail
Lining Peeled Off Tool, but also useful for peeling off the exterior
The product name is Lining Peeled Off Tool, but it is also useful for removing the exterior.
There are two types of shapes, and the principle of leverage makes it easy to apply force, but it is likely to break if force is applied too much.
It's better to break it before the exterior cracks, though,
PushPins and other difficult-to-remove items can also be removed.
When using the product, cure the contact surface with Curing Tape, etc. before use.
View detail
Where Solder is connected, etc.
It can be used for branching connection with a solder, protection of Cable, etc.
It would be better to shrink them with a heat gun, but they are shrinked by lightly frying them with a lighter.
Be careful not to put the flame too close to it or it will melt.
View detail
Used to extend BlinkerWiring
Used to extend the Right Side wiring as it was too short when replacing the Rear blinker.
Naturally, we were able to extend it without difficulty.
View detail
Used for Wiring processing
After all, using a decent tool will ensure a clean and fast completion.
This is one product I wish I had bought earlier.
View detail
To renew the terminal where GreenBlue came out.
I bought a battered 900SS (900SL) and am Restore.
The body of the car is in shambles, but the Harness is fine! There is no such thing as a "wiring".
As in older Italian cars, there is a Bullet Type Terminal connection on the large quantity, which is suspect due to corrosion and other problems, so we decided to redo it.
These are best new!
We were not sure how many we would need for the entire body of the car, so we bought 30 more for now, including the stock we originally had on hand, with the expectation that we would not run out.
Male and Female are Quantities:It is not a Set, so it would be nice if the application is to use only One Side for Large quantities.
(I actually had to use only Male this time when I converted RearBlinker to LED)
It is a common Bullet Type Terminal and has no excess or deficiency in performance.
The surface finish, ease of crimping, feel when inserted, ease of removal, and ease of pulling out are all standard.
Since there is no such thing as too many Bullet Type Terminals, buying them in bulk is a recommendation because it saves you from having to go out and buy terminals when you need them.
View detail
To renew the terminal where GreenBlue came out.
I bought a battered 900SS (900SL) and am Restore.
The body of the car is in shambles, but the Harness is fine! There is no such thing as a "wiring".
As in older Italian cars, there is a Bullet Type Terminal connection on the large quantity, which is suspect due to corrosion and other problems, so we decided to redo it.
These are best new!
We were not sure how many we would need for the entire body of the car, so we bought 30 more for now, including the stock we originally had on hand, with the expectation that we would not run out.
Male and Female are Quantities:It is not a Set, so it would be nice if the application is to use only One Side for Large quantities.
(I actually had to use only Male this time when I converted RearBlinker to LED)
It is a common Bullet Type Terminal and has no excess or deficiency in performance.
The surface finish, ease of crimping, feel when inserted, ease of removal, and ease of pulling out are all standard.
Since there is no such thing as too many Bullet Type Terminals, buying them in bulk is a recommendation because it saves you from having to go out and buy terminals when you need them.
View detail
Ideal for Repair
I purchased this product to refresh a MotorcycleParts terminal cover that was given to me by a friend because it was yellowish and deteriorated. I recommend periodic replacement of the cover because many people use the cover for many years without replacing it, causing it to become damaged and short! View detail
put together in a presentable manner
Recent Small blinker wiring is ultrafine
It's as if it would tear into a thousand pieces if you applied a little too much force.
If you attach it as it is, it will surely break off.
And it looks bad Parenthesis.
So I reinforced it through Tube.
Finished by decorating with an Amigumi Sleeve
Just this much will make it look so much better.
It's definitely better than the BlinkerWiring roundup.
View detail
Trust.
It claims to be weather resistant, so trust it anyway.
I have always been an Emon believer.
… I don't think it's any different than the others, … (laughs)
2sq for Grounding Wire.
View detail
Emon Terminal cover
The cover is quite large for a terminal cover for motorcycles, and if it is for a large type of car, I would have liked to see a description to that effect. View detail
1pc. is useful for various purposes
[How is it used?
I bought it to use as a Drain pan for Oil change.
Oil replacement
Chain cleaning
Parts and tool storage for replacement of OthersParts
It is used for
Was the one you received as per Image?
I thought it was smaller than I expected, but considering that I was going to put it under the belly of the Panigale, 5LiterSize was just right in terms of Clearance.
How was your experience with it?
Oil replacement
In the case of Panigale, it produces about 3.5 liters of waste oil, but the weight of the oil causes it to deflect quite a bit.
There is a scale, but it cannot be used as a scale because there is only a line in one place.
Chain cleaning
I also use it as a receptacle for chain cleaner during chain cleaning. the size is just right and the area around it is now dirt free.
Parts and tool storage
When replacing or removing parts, it is easy to keep bolt nuts, etc. in the box and organize them without losing them.
[Points to note]
Material:It's not like a Stainless Steel pan or something, so I think it might deflect and spill if poured in parallel.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
For Wiring processing
Purchased for Wiring process. No problem. View detail
For Wiring processing
Purchased for use in Wiring process. No problem. View detail
For Wiring processing
Purchased for Wiring processing. No problem. View detail
Quantity for Motorcycle also concerned about car inspections.:2pc. Buy the set
The smoke bomb had expired at the time of the inspection, and at this time, the smoke bomb was for Motorcycle and Quantity for Vehicle.:I bought 2pc
There was also a separate LED light, but I have a regular light separately, so this is the one I used this time.
Light intensity is satisfactory.
The included batteries are for test use and may not last very long, but spare batteries (Alkali AAAQuantity:I think there is no problem as long as you also have a 2pc) or replace it every 12 months or every inspection.
The texture of the lid is a little hard to open, perhaps because it is waterproof, and the "+" and "-" characters are hard to read for people with aging eyes. (Lol)
But the cosmetics are very good considering that they can be used for a long time after replacing the vehicle.
I also have an Emerson LED Sparkle light as a substitute for the triangular version, but it is best not to use it.
The Sparkle light is a very small size that goes under the Seat, but if you can fix it in an inconspicuous place such as inside the Cowl, we recommend that you do so.
Waterproof property seems to be quite strong, so.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
It's strong enough.
In order to use the Portable navigator mounted around the Handlebar and the DriveRecorder (DAYTONA DDR-S100) mounted on the Rear as a Mobile Battery drive, it became necessary to install a Mobile Battery around the Handlebar. The need arose to install a mobile battery around the handlebar.
I wanted to be able to easily attach and detach the Mobile Battery, so I attached the mount of REC mount+ to the Handlebar Brace and attached the Attachment to the Mobile BatteryBody to be able to use it. I wanted to use an existing Attachment, so I decided to use a Smartphone Holder that I had left over.
I had a double-sided tape of 10mm width, so I could use them side by side. I had 10mm wide double-sided tape, so I could use them side by side, but I thought a single piece would be more secure, so I bought this Seat type.
Since it is for in-car use, it may not be good in the rain, but I don't ride in the rain, and since the Mobile Battery is not waterproof to begin with, and I intend to remove it as soon as it rains, I consider rain to be of no concern.
There is nothing special about this ordinary double-sided tape, so all you have to do is cut it out and paste it. The only things I took care of were to wipe the surface to be attached, this time both Mobile Battery and Attachment, clean and degrease them, and to work so that the tape would be attached in one shot to the targeted position. I also made sure to apply the sticker in one shot at the target position.
The price may seem high for the Size, but it is securely attached, so I don't think I will drop it while driving.
View detail