Reviews
Fits: KAWASAKI Ninja1000, KAWASAKI Z1000
Shinobu Sen Rear Torque rod
We stocked RearTorque rods from Shinobu Sen.
It is almost a visual obsession!
Dare I say, lightweight? (^^)
Is this Torque rod as accurate as the OEM Torque rod?
OEM was quite hard and used SmallHammer for removal.
The external Torque rod did not go in easily.
But since I had already removed it, I put it in by tapping hanghang with Hammer while checking the insertion angle.
Remove it with no care and install it with the latest care to put it in!
Finally, the specified Torque 3.5kgf-m is installed using the Torque wrench.
The rest is done by applying a split pin to prevent ha-gap!
Except for the difficulty of removing and inserting, I think it is an easy task even for beginners. (^^)
View detail
Fits: KAWASAKI ZrX1200DAEG , KAWASAKI ZRX1200 R
Processing Required
Is this incompatible with Active's Rear caliper support?
I had to use Grinderetc. to cut off the radius to install it.
View detail
Lightweight and Dress-up
It is for GS400, but I was able to install it on GSX250E as well.:AluminumStraight shape but no interference with Tire and seems to be strong enough because of its thickness. It would be nice if the price were a little lower. View detail
Fits: KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750
THE detail that does it all.
A piece can be seen, a change without really noticeable effect. but a more qualitative visual on the kawasaki 750 Zéphyr. -------------------------------------------------- -------- A room can see, a change without really significant effect. But a more qualitative visual on the Kawasaki 750 Zephyr. Powered by Google Translator View detail
na metal craft torque rod
pure quality , perfect fit and sits nice next to the gold caliper , very high quality , and will never rust great , brembo calipers are next on the bucket list , then ohlin rears View detail
Fits: KAWASAKI ZrX1200DAEG , KAWASAKI ZRX1200 R
A bit lighter
I replaced the NORMAL steel Torque rod with this one to reduce weight and appearance. It is light because it is made of Duralumin compared with NORMAL which I removed. Because it interferes with the Wheel when pulling out the Bolt of the front side to the inside, it was troublesome because it was necessary to loosen the Excessen and move the Wheel to the front, but the texture is good and I am satisfied. View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
From OEM
Replaced a RustRust OEM. no worries about Rust as it is Stainless and the width fits fine so I am happy with it. View detail
To make MONKEY a 14-Inch
Used to change MONKEY's rear wheel from 8Inch to 14Inch It was
The rear wheel used is a LITTLE CUB
MONKEY's Rear brake has a structure where the DrumPlate fits into the swing arm groove But the Rear brake and DrumPlate from SUPER CUB and LITTLE CUB are The Swing Arm and the Torque Rod are used to hold it in place
Therefore, in order to put a LITTLE CUB REAR wheel on MONKEY, you must have You will need to accept the Torque rod
If you have a welding machine, you can weld the Mount to the Swing Arm in a freaky way, but I don't have one, so I decided to mount floating
Probably Repair Parts of some kind
I found it by accident and it was quite nice
Of course, it can't be said to be unprocessed in order to put in the Wheel, but Swing ArmLeft Because it only extends the Axle Shaft hole of the Side, if you have a Leutor or electric drill, you can use it It's manageable
The Swing Arm width was the same, so even if you remove the unique wheel of the SUPER CUB, the hub is still the same We were also able to make use of a structure that doesn't fall off
I've let go of the MONKEY I made now, but I may make it again, so I'll be a little more I hope you keep selling them
View detail
good
I used it on my Z series Rear
I wanted to mount the Caliper to the underside, and even more so, I wanted to make it a rigid mount I was looking for a short size Torque rod
With the shortest cooking, the distance between the center of the hole and the center of the hole was approximately 270mm, so Caliper's position is now just below us
I'm very happy with the position I've found myself in
I chose Silver and the Design is perfect
View detail
Fits: KAWASAKI ZRX1200 R, KAWASAKI ZrX1200DAEG
For appearance
It is a Parts whose performance does not quite understand to an amateur like me.
Making is well done and may look good as one point.
View detail
Clean cutting products.
Steel's Torque rod of OEM tried to replace because the paint was scratched and dirty due to rust. I am happy because it is lighter than the OEM because it has a beautiful cutting process and the finish of Anodized is glossy. By the way, in my case, when I installed it properly, the Rubber cover covering the previous Bolt interfered with the Exhaust System and it seemed to melt so I attached it to the reverse side.
I hope the price is a little cheaper but I guess there is no way to consider processing Cost.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB900 F ALL MODEL (SC09), HONDA CB900 F ALL MODEL (SC01), HONDA CB750 F (RC04)
Since it is a Titanium, compared with the iron of a NORMAL, it is markedly light, and there is also a high grade feeling. Satisfied [ since it however purchased in order to equip with the Tire of 140 Sizes primarily, but it still continues being sta
Since it is a Titanium, compared with the iron of a NORMAL, it is markedly light, and there is also a high grade feeling.
Satisfied [ since it however purchased in order to equip with the Tire of 140 Sizes primarily, but it still continues being standard size, it does not understand / whether was really required and /, but ] for the time being.
View detail
It changed, when exchanging the Webike Monitor Swing arm and a Wheel. rigidity and brightness do not accumulate. Mr. OVER, the highest.
It changed, when exchanging the Webike Monitor
Swing arm and a Wheel.
rigidity and brightness do not accumulate.
Mr.
OVER, the highest.
View detail
When exchanging a Caliper, it purchased together. It is a Polished if a feeling of appearance * rigid feeling * brightness * Caliper support is also made the product made from OVER!!
When exchanging a Caliper, it purchased together.
It is a Polished if a feeling of
appearance * rigid feeling * brightness *
Caliper support is also made the product made from OVER!!
View detail