Reviews
GILD Rear Caliper holder for Brembo P2 rear brake
About quality and texture Top quality aluminum bracket. With smooth finishing. The weight feels ok. Not too heavy or too light. It also comes with brembo fiting stainless steel screws. About the feeling of use Looks perfect in silver with my gun metal brembo rear brake. Products to buy together Bought it with brembo P2 with red logo. Item number 20.B852.78 Difficulty of installation Installation maybe shorter if the rear rim is easily removed. The fitting of the rim which takes a while. I replaced my rear hose so the total time about 2 hours. But just fitting the caliper and bleeding the hose maybe just an hour. Cost performance and comparison with other products Price is around slightly cheaper than the other brands but the finish is not short of the others I guess. About shipping and packaging Come in plastic wrap with bubbles wrapping for protection by seller. Shipping cost is not expensive as the item is not very big. Any concerns, cautions, or advice when purchasing The only concern is that the item maybe scratched as it's only cover by plastic but the seller did a good job by protecting it. And the item is made not easily scratch too. View detail
Processing is beautiful
Bolt and Shim will be provided separately.
M10×25?Pitch1.5 and M10×25?Pitch1.25 are available.
The processing is beautiful and the rigidity seems solid.
I would have liked Bolt and Shim to be included if possible.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S
Active Rear Caliper support
Purchased this for the Swing Arm and to replace it with a Brembo caliper. View detail
Fits: YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA YZF-R25
On the 2020 R25.
I put it on my R25 with Inverted Front Fork normally without any problem.
The durability is unknown, but the construction is solid, so it should be no problem. I am satisfied.
View detail
![[Closeout Product]Rear Brake Caliper Bracket for Brembo Rear caliper support[special price]](https://img.webike-cdn.net/catalogue/images/99779/id5044981_1_TS.jpg)
Fits: KAWASAKI ZX-14R
Sale item was cheap.
For a little over 10,000 I was able to buy a Support for the new ZX-14R Crab.
This is an unbeatable price
OEM is weak, so the new Crab and Gale's Small diameter MASTER.
Increase braking power.
View detail
Fits: KAWASAKI Z, KAWASAKI Z1, KAWASAKI Z2
SSItoCaliper support
The installation was very easy, as the center of Caliper came out without any fine tuning using .Shim because of the good accuracy of Support.
The included Bolt also has a hole drilled for wiring, so wiring comes out as it is, so it is a recommendation.
View detail
Fits: YAMAHA FZR750R, SUZUKI GSF1200S, SUZUKI GSX1300R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, HONDA CB1300SF, SUZUKI TL1000S, SUZUKI TL1000R, SUZUKI GSX-R400R, SUZUKI RGV250Γ, SUZUKI RF900R, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GS1200SS, SUZUKI BANDIT400
You can trust me.
I bought it from another Motorcycle and had no problems, so I trusted them. View detail
Fits: KAWASAKI ZX-10R
Pad position is subtle
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Purchased to improve serviceability by underlining.
ABSFlareBlock, Hose (635mm), Fitting (20°), Mount Bolt (M8*20) are required for installation.
The swing arm needs to be removed when wiring, so it is quite large.
I used it on a new Crab, but the pad sticks out, so I had to shave about 5mm off.
I was able to do this in about 5 minutes because I had Leutor and TungstenBit, but if you only have File, this is also Large strange.
Weight is Quantity for Bracket and Caliper:It was almost the same as OEM with Set.
The design of the cutting groove was uneven (white spots) and the texture was not good. （The texture was not so good, but the others were good.
View detail
Fits: HONDA CB1300SF, HONDA CB1300SB, KAWASAKI ZrX1200DAEG
Beautifully made, perfect fit.
I'm really happy with the quality of these parts, they fit perfectly and look beautiful, they really add to the high quality look I was trying to create with Öhlins forks, Dymag carbon wheels and AP Racing calipers, Superb service from WeBike. View detail
Fits: HONDA CBR600F, HONDA CBR400RR, HONDA CB750, HONDA CB400SF, SUZUKI IMPULSE400S, SUZUKI IMPULSE400, SUZUKI RF400RV, SUZUKI GSF750, SUZUKI RF400R
Match CB1100 Fork with Initial ModelABS.
[How is it used?
The normal fork of CB1100 except RS has a caliper pitch of 62mm and 80mm. This item is for CB750 (RC42 ) It corresponds to 80mmPitch as well as etc.
The caliper side is compatible with bremboAxialCaliper 40mm.
Was the one you received as per Image?
The product seems to be Active and is working well with no accuracy or quality issues.
Was the installation difficult?
It is a Bolt On, so it is easy to install. In my case, there was a slight interference between the Caliper and the disc mounting Bolt base of the Wheel, but I was able to get it out by shifting it slightly.
How was your experience with it?
Since the Caliper position is at the top compared to the Fork of the 62mmPitch, it can go without the Hose extension. It also looks more natural.
[Included Parts:were they on?
In addition to the Instruction Manual, Bolt and Shim are included.
[Was there anything that disappointed you?
The quality of the product is not particularly problematic, but the high price is disappointing.
The recent price increase due to price revisions has made it even more expensive.
The same manufacturer's support with a 62mm pitch is often available, but the 80mm pitch one here may be special and is not available at all in the second-hand market.
View detail
Fits: HONDA CBR600F, HONDA CBR400RR, HONDA CB750, HONDA CB400SF, SUZUKI IMPULSE400S, SUZUKI IMPULSE400, SUZUKI RF400RV, SUZUKI GSF750, SUZUKI RF400R
Fits front forks with CB1100 ABS of some years.
[How is it used?
I purchased the Fork/Caliper pitch 80mm/40mm to fit an older CB1100 Fork with ABS.
Was the one you received as per Image?
Quality is as high as the Image.
Was the installation difficult?
Basically Bolt On, but if it has ABS, it is better to install in Shop to make it work properly.
How was your experience with it?
It is well made and feels secure. I think it is indeed Active.
Recently, CHINA products have been distributed, but there are some cases where the products cannot be installed due to insufficient accuracy or defective products.
[Included Parts:were they on?
It comes with Bolt and Shim.
[Was there anything that disappointed you?
None in particular. Satisfaction level is high.
▼ CB750 (RC42) It is the same pitch as the Fork of the STD Disc and fits the diameter of the STD Disc.
View detail
Fits: YAMAHA FZR750R, SUZUKI GSF1200S, SUZUKI GSX1300R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, HONDA CB1300SF, SUZUKI TL1000S, SUZUKI TL1000R, SUZUKI GSX-R400R, SUZUKI RGV250Γ, SUZUKI RF900R, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GS1200SS, SUZUKI BANDIT400
That's what Active is all about!
I purchased ActiveSupport along with my brembo equipment. I personally like this manufacturer and the quality and price are very attractive. I am very satisfied with the center and the quality of the product. It may be a little expensive, but it is a product that you can be satisfied with once rather than losing money buying a cheap one. View detail
Fits: KAWASAKI Ninja 150RR, KAWASAKI Ninja 150RR
I finally found it, but...
The Disc Rotor in NORMAL is too small and the pad does not hit the entire surface.
Large Disc Rotor must be replaced.
View detail
I wanted a Size notation.
I bought it to use for bremboRear caliper center out, but the bolt size was for M10.
RearCaliper bolt cannot be used because it is M8.
There is no Manufacturer notation, only thickness, and I would like to see at least Bolt diameter indicated.
It is now in the collection of Parts.
View detail
Fits: KAWASAKI ZXR750R, KAWASAKI ZXR750R, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZX-9R, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI ZEPHYR400X, KAWASAKI ZEPHYR1100, KAWASAKI ZZR400, KAWASAKI ZZR1100C, KAWASAKI ZZR1100D, KAWASAKI ZX-9R, KAWASAKI GPZ900R
Purchased for installation of Brembo caliper
I bought this product to install Brembo caliper. The texture is good.
RightLeft and backside engraving for installation (Landmarks) It would have been nice if there had been a detailed Instruction Manual that would have helped me understand the installation orientation. I had a little trouble installing it. (Is it just me?)
View detail
ZX-6R Fitment
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX636
Fitment Issue
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: KAWASAKI Z1, KAWASAKI Z2
For Upgrade of Normal caliper
Converted from KawasakiZ1 OEMCaliper support.
Quintessential Over.
Aluminum Cut-out texture is the best finish.
We chose Silver to be One point.
The pad moves smoothly because the pad entry point has been polished. I use this pad with Vesra's Shim pad, and there is no squeal at all.
If you want to use double diskSpec., you will inevitably need two of them, but two Supports will cost 50,000 yen over.
It is a fun part, but it is a very satisfying part.
View detail
Fits: HONDA CBR600RR
Complete design error
I installed the pad on a '07 model, but due to an obvious design error, the mount position of the brembocncCrab caliper is 5mm outward gap compared to the OEM disc diameter of 220mm, and the pad protrudes when installed as is.
The disc diameter of 230mm is not so common, and the only way is to shave 5mm off the disc contact surface of the pad and forcibly fit the pad to the disc.
There is no Caliper center, and the center must be adjusted by placing a Shim between the Mount section.
At any rate, it is not a Level product that can be sold.
View detail
V-max 1200 Rear Brembo caliper support
V-max 1200 Rear Brembo caliper support. Perfectly compatible with Brembo 2p calipers. It is also an overlacing product. View detail