- Home
- Product reviews
- Motorcycle Parts
- Brakes
- Caliper Support Bracket
- ZX-6R Fitment... (WR3: Rear Brake Caliper Bracket for Brembo)
【WR3】Rear Brake Caliper Bracket for Brembo Review
ZX-6R Fitment
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money.
อุปกรณ์ประกอบ ZX-6R
เกี่ยวกับคุณภาพและเนื้อสัมผัส : งานเครื่องจักรดูดีมีรูปลักษณ์ดี เกี่ยวกับความรู้สึกในการใช้งาน: ไม่มี สินค้าที่ซื้อร่วมกัน N/A ความยากในการติดตั้ง : ไม่เหมาะกับ ZX-6R ปี 2019-2023 หน่วยนี้มีปัญหาหลายประการ เส้นผ่านศูนย์กลางเพลามีขนาดใหญ่เกินไปที่ 27 มม. แทนที่จะเป็น 25 มม. สำหรับ ZX-6R แขนกันหมุนเพื่อยึดตัวดึงสวิงอาร์มไม่ถูกต้อง หากคุณจัดตำแหน่งให้อยู่ตรงกลางเพลา แขนจะตั้งมุมขึ้นแทนที่จะอยู่ในแนวนอนพร้อมกับตัวดึงซึ่งจะไม่อนุญาตให้เคลื่อนที่ไปข้างหน้าและข้างหลัง หากอยู่ในแนวเดียวกับตัวดึง รูเพลาจะสูงกว่าที่ควรจะเป็นประมาณ 10 มม. และไปทางด้านหลังประมาณ 5 มม. ประสิทธิภาพด้านต้นทุนและการเปรียบเทียบกับผลิตภัณฑ์อื่นๆ เกี่ยวกับการขนส่งและบรรจุภัณฑ์: ดี ข้อกังวล ข้อควรระวัง หรือคำแนะนำใดๆ ในการซื้อ: อย่าซื้อ!!! เสียเงิน.
Show originResponses
Other reviews
ZX636-2019 Rear caliper support
Mounted on ZX6R-2022
First of all, the diameter of the Axle Shaft is completely different! The angle of the Swing ArmCaliperStopper is too large for the Axle Shaft to fit through.
I managed to install it, but the Brake Pads were about 1cm outside the surface of the Rotor ….
Dangerous because it is a Brake round!
View detail