Reviews
After all, Universal
The welding of the outer Flange section was messy,
ManufacturerThey were outside the published dimensions and did not fit delicately.
I was able to shave it down somewhat File and put it in.
The sound seems to have quieted down some … though,
It is best not to expect a muffling effect.
Improvement of the smell of the exhaust Gas is clearly effective, though,
It is no match for the OEMExhaust System catalyst.
It still smells even at RPMs that should have reached the reaction temperature.
We recommend that you purchase the product assuming a reduction of about half.
View detail
Small
Waist circumference is quite small in relation to the value.
32 (90cm) I bought a pair of 85cm Pants, but they are as tight as or slightly tighter than the 85cm Pants I am currently using from another company.
In contrast, from thigh to hem, it is too loose.
I am wondering which MODEL arrived at hand, before or after SizeRenewal.
For some reason, a 32inch 81cm Seal was posted, but I think this size is closer.
I bought this size because I wanted to wear it loosely around the Waist area, but unfortunately, I have to keep it.
View detail
Anyway, it's expensive!
[Personal Thoughts
Good impression
Looks great! It also improves the footing somewhat!
Bad impression
It is shaped to prevent the body from falling backward for the Drag race, but it seems to be effective only when the body is bent over in a forward leaning posture. If you sit on it normally, you might slide backward. I thought it should have more angle.
Seat is much harder than NORMAL.
The fabric makes the seat slippery and my butt slides around.
Bracket needs to be adjusted because the mounting bolt does not fit easily.
The back of the Seat is very poorly made. There are many scratches on the back of the Seat, which are caused by cutting the excess fabric with a cutter. (Lol) SeatSome stains are stuck in the gaps between the seams that can't be removed.
Na! Ni! Yo! Ri! … It's crazy expensive!
With an outside Seat, you can buy two.
I would have preferred to buy an OEMColored Seat?
View detail
Fits: SUZUKI V-Strom 650, SUZUKI V-Strom 1000
Even if Size is past Limit….
The film is hard and fits in the MeterSize Limit. I managed to install the film, but after washing the car, the film started to float when I blew off the water droplets with a compressor.
I stuck it again, but I am not sure about its durability. Is the size still not right?
View detail
No functional problems, but ….
No functional problems, but the paint started cracking and peeling about a year after installation. There is a problem with the quality of the paint or the painting method. View detail
The suspension does indeed move.
I have been interested in this product for a long time, but I was hesitant to purchase it because of its high price. I think the NORMAL ASKUL was the right choice by chance. I think the NORMAL ASKUL was the right choice by chance, but I will continue to use it because it is certainly better. View detail
Maybe a little longer.
The length is so long that it is kind of unsettling. I feel like it could be 5 cm longer. View detail
Shipping is good.
It is only now possible to attach an external DialWire lock to the Handlebar.
I think what you want to do is reasonable.
However, we still would like to see some improvements due to the use of existing locks.
1.Dial is Smaller
I don't want to touch it in the winter or anything.
2.Wire is too long.
Handlebar position could be half as short as it is now.
3.Lock position
Not the other way around, as they tend to pop up on the Grip side and interfere with each other.
I dare to put it on the other way around.
It would be nice if this area could be improved, but it is regrettable.
View detail
It's a shame … when it's on.
I would not have bought it if there was a picture of it with the Lens removed. I would not have bought it if there was a picture of the Lens removed. View detail
Fits: HONDA CB900F, HONDA CB900F, HONDA CB750S, HONDA CB750S, HONDA CB750L, HONDA CB750K, HONDA CB750K, HONDA CB750K, HONDA CB750K, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750, HONDA CB750, HONDA CB750, HONDA CB1100F
Oil change
I am replacing the seal along with the Mission oil change, but it is a bit expensive. It is just a sealing washer, but I feel it is expensive because Bolt is too cheap. View detail
![Lowdown Link [CB1300SF (SC54): CB1300SB (Super Bol D'Or)]](https://img.webike-cdn.net/catalogue/18801/sc54ldsv_TS.jpg)
Fits: HONDA CB1300 Super Four, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR
Try to install it
The head of the cap bolt does not fit due to an error in the dimensions of the product's mounting holes. (I screwed it up forcibly.)
Insufficient explanation in the InstallationInstruction Manual (There is no description of the front and rear Bolt attached to the product. I think it is probably StopperBolt)
The Instruction Manual notes that the Side Stand will be standing up, but it will stand up quite a bit, so it needs to be modified.
It is written that the rear suspension tension should be increased to avoid interference, but even if the tension is increased, the reserver will hit the suspension when the rider straddles it, and it is impossible to ride without modifying the cowl or replacing it with a suspension without reserver.
However, the effect of Lowdown is immensely Large.
View detail
Installer's Decision
Prerequisite for description:OEM Grab Bar + Arch Long tail installation
good point
Long tail and OEMGrab Bar interference improved
A bad point
Spacer above the interference level, so it loses its function as a Pillion Bar. (There is not enough space between the long tail and the grab bar to accommodate gloves.
reference
If you want to keep the design and functionality of the Grab Bar, I recommend purchasing the Grab Bar from Archi.
In the combination of OEMGrab Bar and ArchiSpacer, the Manufacturer name (kawasakietc.) behind Seat is hidden by the Grab Bar.
View detail
It's hard to install
Cowl was burnt due to interference with the lower part of the vehicle body.
Since it is installed inside the cowl, there is a limit to how much modification can be done, so we gave up on using it.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Tie Wrap Fixing is too sad.
The product itself is well Large body Large sturdy.
It is too bad that it is planned from the beginning to just stop at Tie Wrap.
If you use double-sided tape, it will be a hassle later, and the Tie Wrap itself has to be very long. (It is included in the product, but the quantity:2pc only)
In case of OEM Exhaust System, it is better to remove only Silencer. It will be a huge obstacle. It may be possible to put it on without removing it, but you don't want to get scratches all over it. It can be removed with 3 Bolts on one side. After all, it is faster and easier.
I didn't understand what the Instruction Manual was saying for a while because it was just text.
If you know what I mean. Manufacturer doesn't want to take care of anything." I think it says "I'm sorry, but I'm not sure. After all, there is no reference to the installation itself. I wonder what is this Manufacturer….
View detail
![Brake Pad - Racing [RC] Compound](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0296/23955300_20220325114547401_TS.jpg)
Fits: SUZUKI KATANA, SUZUKI GSX-S1000 F, SUZUKI GSX-S1000, SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI GSX-R1000, KAWASAKI ZX-14R, KAWASAKI ZX-10RR, SUZUKI GSX1300R HAYABUSA, SUZUKI GSX1300R HAYABUSA, SUZUKI GSX1300 HAYABUSA, SUZUKI GSX-S1000, DUCATI 848EVO, DUCATI 1198, DUCATI 1198 SP, DUCATI 1198 S, DUCATI 1198 R, DUCATI 1098, DUCATI 1098 S, DUCATI 1098 S TRICOLORE
price-performance
The effectiveness is only slightly better than For Street, and the durability is not good.
5Quantity in 1Season:Set consumed.
I was attracted by the price and tried it, but as a result, it was not cosmetic considering the frequency of replacement and maintenance.
View detail
It's a shame, because Parenthesis looks great.
[How is it used?
I switched my car to a Z900RS and the NORMAL sound was not bad, but
Purchased because the sound quality was a little different from my taste and I wanted to change the appearance and reduce the weight.
The following imprements were installed on a previous Z900 (unmarked)
Full titanium exhaust & SC1-RSilencer by SC-PROJECT
This is a very dry comparison with
Was the one you received as per Image?
Material:I found it surprisingly heavy for this Size in Titanium.
The slanted area on the opposite side of the exit has a rough surface like sharkskin.
Was the installation difficult?
When installing the inner baffle, use a ring to hold it down so that it does not wobble inside.
The system allows the user to enter the parts, but there are many similar parts, so it was difficult to know which parts to use.
I wish they would number the bags containing the Parts.
Silencer band is included, but you need to prepare your own bracket and bolts for fixing.
You need to be creative and inventive yourself.
I installed it in combination with K-fac's CLRExhaust pipe,
The bracket is Nankai Parts' Universal Bracket Length 225mmOffset 75mm (Part No. MSTL-225FR-75),
The silencer was fastened to the OEMLoading Hook by using the OEMSilencer Fixing Bolt.
Spring is the one that came with the CLRExhaust pipe.
However, the Silencer band is a little small in diameter and deformed when used as it is.
The bracket is then connected to the OHLINS Preload Adjuster.
Spacer of 3mm was put in because of interference.
How was your experience with it?
In combination with K-fac CLRExhaust pipe, even with inner baffle in place.
Considerable blast from Idling.
It might be more annoying than the SC-PROJECTFull Exhaust System without Baffle that was installed on my previous Z900 with the same Straight structure.
The Z900 series has a high ColdStart Idling.
Idling in a residential area is a Level that is sure to be Objection from neighbors.
Baffles can be attached to the exits as well,
It sounds like a whistle, like a Large Dump car, and I can't bring myself to use it.
The sound quality is rough and muddy from Idling with CLRExhaust pipe + Inner baffle.
The sound does not become a clear high-pitched or pleasant sound as it is turned, and it remains a harsh, dusky sound until the very end.
The trend may be similar to the OEM sound.
It seems that the inner baffle is causing a lot of exhaust resistance.
I don't feel that the low speed Torque is extremely gone and AfterFirea is not at all.
I feel that the performance has been downgraded quite clearly because it feels like it is jammed on top despite the bombast.
I tried running the next day WITHOUT Baffle's full Straight and it was so loud that I could say it was heinous.
Level, which is no different from the straight pipe of a family car.
The sound quality and running are better than with Baffle, but at any rate, it is too noisy.
It is highly likely that we will abandon the use of the system, although we need to consider whether we should compromise on driving and sound by emphasizing style.
Very disappointed because I like the look of Large.
Link pipe and Quantity as Slip-on Silencer for Z900RS OEM exhaust pipe:There are some that are sold Set.
It might work there.
[Included Parts:were they on?
・Instruction Manual
Silencer Band (possibly Material):(Stainless Steel)
Adapter for mounting on 54mm exhaust pipe, Spacer, etc.
1 pc. each of exit and inner baffle for installation.
K-fac Emblem
(Spring not included)
[Was there anything that disappointed you?
I was expecting the sound quality to be clear and pleasant like the previous SC-PROJECT car.
With Baffle, it was like a very loud OEM that I didn't like.
The sales pitch was that the volume could be adjusted by using a combination of inner and exit baffles.
The volume of the Inner is not as low as expected, and the sound quality is poor.
Exhaust resistance is too Large and performance is down from NORMAL to Large.
Other items that would be helpful
Items to buy together:.
This is a Universal Product, so brackets, springs, bolts, etc. for fixing the silencer are required separately.
View detail
I bought it to install it, but I couldn't.
[How is it used?
I bought it for the Rear Mud Splash, but unfortunately it didn't work.
Was the one you received as per Image?
Image was great, but I made a mistake and I just couldn't get it installed.
How was your experience with it?
Installation could not be done
I made the mistake of buying it.
[Points to note]
It is a good product, but could not be installed on the HUNTER due to the shape of the Rear Fender.
Of course, I tried to see if I could install it on the Front, but it was still impossible.
How did it compare to other products?
No comparison.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
I think the person who purchases it can install it on other models.
(As a precaution.)
I was wondering if the CT110 HUNTER CUB needs to be Rear Fender processed on the day of the product itself.
View detail
Fits: KAWASAKI ER-6F, KAWASAKI ER-4N, KAWASAKI Z250, KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1100II, KAWASAKI Z750S (water-cooled), KAWASAKI Z750 (water-cooled), KAWASAKI Z750 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI Versys 650, KAWASAKI Ninja 650R, KAWASAKI Ninja 650, KAWASAKI Ninja 250R, KAWASAKI Ninja 250, KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI ER-6N, KAWASAKI ZX-6R, KAWASAKI ZX-7R
Misleading product photo
The photo shows the connecting kit for a universal handlebar type, although the motorcycle fitment list showed only certain variants of Kawasakis. This led me to believe the listed Kawasaki models used a mounting method that would be compatible with universal handlebars, or that different connecting kit options would be available in the package. None are, and there are no other places to order a connecting kit for these bar ends other than some small shop in Taiwan. As a result these bar ends are now an incredibly expensive paper weight for me. View detail
Large change in installation work
If you remove the handlebar cover of the scooter, a hole will be made there, and you just want to hide it.
I happened to have another job to replace the handlebar, so I worked on it in conjunction with that. In addition, there is nothing to hold the parts in place, so you have to use gold glue to fix the handles in place.
If you are not confident if you want to replace it, I suggest you ask Shop to do so.
View detail
![S17 [SYNTHESE 17] Shoes](https://img.webike-cdn.net/catalogue/images/87594/358d5f6fed03f1e80fa70f07fb2b0f35_TS.jpg)
Toe section too thick
Holdability of the ankle area is very good, but it is difficult to operate with a vengeance.
Thick from the toe to the instep, making it difficult to insert the Shift when moving up.
View detail