Reviews
Even a custom novice could install it.
I installed this product on a CT125 JA65, and although I am new to customization, I was able to remove the existing frame and install this product without any trouble. Although the Instruction Manual mentioned that there is an upper and lower joint frame, it was difficult for a layman to understand the diagram for distinguishing between the upper and lower frames. It was difficult for a layman to understand the diagram for identifying the top and bottom. I thought that only a person who could read drawings could understand it. Apart from my impression of the product, I was also not impressed that I could finally buy the product more than three months after each Site listing began. View detail
Fits: KTM RC8, KTM RC8R, KTM DUKE, KTM Adventure
Good vibes
It was the right product for my needs. View detail
Convenient for length adjustment
When tightening the Screw
It would have to be a narrow Socket to fit.
I fixed it with Locktite243.
It has loosened under the weight of the car.
I fixed it with Locktite263 and it stopped working.
Maybe you can't take it off now. w
View detail
Yoshimura racing sider kit
After delay due to our of stock.finally it arrived.as usual.packing was excellent.no regrets..product is better looking as in picture..not heavy as predicted.highly recommend.. yoshimura product never disappoint. View detail
Fits: HONDA REBEL250, HONDA REBEL250S EDITION, HONDA CL250
I'm almost satisfied.
Exhaust system was changed from front pipe to MORIWAKI.
The vibration and other factors had already been improved because of the replacement of the
Frankly, it was hard to tell the effect.
Speed at which strong vibration occurs at high speeds is 3 to 5 km/h
I think it has grown.
I definitely felt that the rigidity of the Frame was slightly increased.
I have seen the video etc., and it has a very good reputation.
The more novice you are, the less likely you are to expect too much.
I am sure we will see the effect after long-distance, high-speed driving, etc.
I did the installation myself, but it is definitely better to have a store do it for normal people!
There is a high TorqueBolt attachment and removal of Engine Jack-up and Engine hanger bolt.
There is Torque management, and a reasonable selection of tools, including a hexagonal box wrench,
It would be difficult without knowledge.
As for the look, it is very good as it attaches to the lonely Engine surroundings.
It would be better if there was a Plating Specification or something like that.
View detail
good-looking
OEM is expensive, so we chose here.
I have not yet fallen over, so I do not know how effective it is.
I think it looks good.
View detail
Fits: HONDA NSF100, HONDA NSR Mini, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape Type D, HONDA Ape 100 Type D, HONDA NSF100, HONDA NSR Mini, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape Type D, HONDA Ape 100 Type D
Axle guard by SHIFT UP
Grom (JC92) I installed it in
Material:With DURACON, it came off from the base when it fell over and had to be replaced even though it was still usable and worn out, but Material:With aluminum, you don't have to worry about that, so you can use it for a long time.
I am very satisfied with the price and the color selection.
View detail
Fits: HONDA DAX125, HONDA SUPER CUBC125, HONDA MONKEY125, HONDA CROSSCUB110
While Compact, it seems to be dependable.
[How is it used?
CROSSCUB110 (JA60) I was looking for parts to protect the engine area of the "K" series cars because the engine area is bare and I was worried that the engine might be damaged by stones or grass when driving on a dirt or grassy road surface.
We considered SP Mukawa's Under Frame Kit, but chose this Engine guard kit, which seemed easier to install.
Was the one you received as per Image?
It was more Compact than I had imagined, but I felt this was a better overall Balance.
Also, the frame is black, so the balance fits well in terms of color.
Was the installation difficult?
Installation is easy as long as the necessary tools are available.
The time required was about 40 minutes even when working slowly.
How was your experience with it?
I have not tried it on Dirtetc. bad road surface yet, but I think it is promising.
[Included Parts:were they on?
There were no missing items and they were all in place.
The Handling Instruction Manual was also easy to understand.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
The Center Stand was set up for installation.
Leisure sheets are useful since we work lying down.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Essentials for Maintenance
Purchased to use the Racing Stand during maintenance.
Therefore, I purchased the least expensive MORIWAKI product, but there is no problem at all in using it.
On the other hand, I wonder if there is any added value in what is effective.
We use STAND made by JTrip, and the body is upright and stable, giving us a sense of security when servicing.
Highly recommended if you are not particular about the appearance.
View detail
Perfect
Quality and Texture Information Lightweight with Aleuminum I think it'll be nice and serve as a guard for the feeling of use Product 498-1300100 to purchase together It's difficult to install The cost performance and comparison price range with other products are similar. You can choose your favorite brand Delivery and packaging to WeBike in a week The packaging is great 2 concerns when purchasing is 1 set You have to buy 2 sets View detail
LOOKS GORGEOUS and ATTRACTIVE
I PURCHASE THIS PRODUCT FROM WEBIKE TO REPLACE MY RUSTY LOOKING SIDE STAND OEM SPRING. FIRST I THOUGHT IT WAS EASY AND LOOKS MATCH FOR MY TDUB SIDE STAND .I have no idea but placed an order anyway.after I got the package I try to replace the stainless steel spring but it little bit way too long had to bend the spring little bit further to clean installation . spring came with the side stand bolt and nut .according to the descrption they all stainless steel .Installed the ss bolt and nut and they exact the same as OEM .THIS SET HAS WAY DURABILITY THAN OEM SPRING BECAUSE IT'S STINLESS STEEL. TIME WILL TELL .Well made by the producer.I WISH I TRY TO USE SHORT SIDE STAND LINK BUT COULDN'T PURCHASE ONE.If I have a short side stand link and won't able to bend the spring.It is not necessary to fold the spring a little more to reduce its length. Without any problem I was able to install it easily because the spring was bent to reduce the length.. GREAT PRICE FOR THE SET.WORTH IT. I can highly recommended this product .WEBIKE Shop is one of the best shop for buy finest quality and rare products for cheap prices.webike shop offers great service.so anyone can buy product with confident. webike packaging is awesome.they secure the items inside the box with the bubble (doesn't matter the product size,they do it anyway ) wrap for further protection.I highly recommended.WEBIKE.. awesome people and 5star shop. .Thank You !!! View detail
Fits: SUZUKI DR250R, SUZUKI DJEBEL250XC, SUZUKI DJEBEL250XC
Large Small Stone Removal.
Not a product for DR250R
As others have noted, it is probably correct for KDX250!
Product for KDX250, but with the screw hole position and part of the product cut off, so that it can be installed on DR250R.
I thought about returning it, but I can install it...
In addition, the product I received had no BALIetc. at all!
It is clean enough, and I think any further end processing with vacuum molding would be a polishing process.
Installation
By re-drilling the two holes behind the screw holes 15mmLeft (moving the rear of the plate to the Right Side of the car body), it was possible to install the screw holes in the normal position.
Normal position:Quantity against U-shaped SIDEGuard welded to Frame:Pair (for Left and Right) Ability to install on an even etc.
The bracket had a 9mm hole, so an M6 nutter (NutRivet) was installed on the bracket side, and a long M6 bolt and a large washer were used to make a surprisingly firm stop.
The angle of the Plate does not match the Frame at all, so we have to bend the Plate forcibly while screwing it in place.
Since the installation was done in winter, I tightened the screws while warming them up with a dryer at first because I didn't want them to crack.
Since it is made of PP, once it is deformed, it will not crack the next time it is installed.
However, it was possible to install it, but it would not be able to achieve its original performance.
The rear part is too short and part of the Frame to SuspensionLINK is not covered.
Therefore, I don't think Link guard can be installed by itself.
However, the main problem is that it is not Fit to Frame because it is diverted from another car. This is due to the fact that the plastic alone is subject to impact.
Frame curvature, which is most likely to be impacted, does not fit the Frame
Specifically, the connection between the down tube side from the Steering base and the Frame coming from under the Engine is bent with a constant R in KDX250, but in DR250R, the welded U-shaped SIDEGuard part is bent in two steps with a straight line!
The straight part does not fit the skid plate, so there is a gap of a little more than 2 cm in the large size.
This is the area where you will get the most hits. Even if your opponent is a log, you'd better stop him.
The thickness of the board is about 3-4mm, so if it is deformed by 2 cm, it will definitely crack.
Unfortunately, it is not a Skid plate, but an expensive Small Stone Removal. Think of it as.
View detail
Fits: SUZUKI GSX-8S, KAWASAKI Ninja ZX-10R, KAWASAKI Z900, SUZUKI GIXXER SF250, SUZUKI GIXXER SF250, SUZUKI GSR750, SUZUKI V-Strom1000 XT ABS, SUZUKI V-Strom1000 ABS, SUZUKI V-Strom1000, SUZUKI V-Strom250, SUZUKI KATANA, SUZUKI SV650X, SUZUKI SV650, SUZUKI GSX-S1000GT, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-S750, SUZUKI GSX-R125, SUZUKI GSX-R125 ABS, SUZUKI GSX-S125
Cool as always!
It's all about YOSHIMURACool! View detail
Cowl drilling required
I ride a CBR600RR (2009).
I purchased this product because I was told it was compatible, but I could not install it without drilling out the cowl.
Fortunately, I did not have to drill holes by diverting the Slider Bracket that I had originally used, but of course I had to choose and purchase the Bolt myself since I could not use Included Parts:.
If you purchase the product, you should be prepared to drill holes in the Cowl.
View detail
It's awesome!!!
Not only does the front-to-back position change, but the side stand is positioned a little further to the left, making the support much stronger. However, the downside is that the support is unstable with the original side stand, so you have to shorten the original side stand or install an adjustable side stand like I did. If you adjust it well, you can park stably on any road that slopes to the left or right. In fact, it would be enough to give it 5 stars, but since I am not satisfied with the combination with the original stand, I give it 4 points. -------------------------------------------------- -------- Instead of simply changing the front and rear positions, the side stand is placed a little more, and the support is very strong. However, the disadvantage is that the pure side stand is anxious. If you adjust it well, you can park it stably anywhere on the side of the road. In fact, it is enough to give five stars, but the combination with the genuine stand is not satisfactory. Powered by Google Translator View detail
Takegawa Sub Frame Kit installed
The Sub Frame Kit was selected because we wanted to keep the width of the CT125 to the sides of the vehicle, and the volume is slightly increased due to the larger pipe diameter. If you tighten the bolt first, the Under Guard will not be attached. View detail
I don't fall down, but I wear it as insurance!
This is AGRAS's Engine slider.
What is a racing slider? ‥
The "Racer" was adopted for the endurance racer, and then it came to be installed as custom parts for motorcycles running on the street. Slider" 。
The role is to protect the Engine and front and rear Axle from Accident and to minimize Damage.
Difference from Engine Guard
The Engine Guard protects the engine from impact with its tough gold material, while the Engine Slider does exactly what it says on the tin. Sliding body." Protect Engine by 。 Therefore, it is installed outside of the Engine and is completely different from the Engine Guard.
Material‥
The material of SliderBody is a kind of resin called “DURACON”, which has moderate strength and hardness. It is not easily changed by heat, etc., and has a characteristic of little fading. When the car falls down during street, winding, or circuit driving, it reduces the risk of chassis damage by mitigating the impact and making the chassis slide.
Merit‥
Prevent damage to exterior parts
The exterior Full Cowl Material is made of resin, so it can be easily cracked by a slight fall.
Repair costs vary, and for foreign cars, it can be as expensive as several hundred thousand yen for One Side replacement....
The MotorcycleSlider prevents such damage!
Demerit‥
▲Increases the sliding distance in case of a fall.
When considering the area of contact with Asphalt during a fall, which would have the smallest resistance to Asphalt, if the entire surface of the cowl were to be scraped off or if a slider were attached and the place of contact with Asphalt was considered to be the point of contact of the slider?
You can see that it is when there is a Slider in contact.
With sliders, there is less contact with the Asphalt when tipping over, which leads to less friction with the road surface and longer run distances.
It is still good in a wide place like Circuit, but it is scary that the run distance is longer when falling down on a public road.......
Jumping out into oncoming traffic, heading for a cliff and not stopping... scary to think about (laughs).
The car was scrapped due to standing fire.
If the motorcycle is in a near-vertical position and falls, the impact of the entire weight of the motorcycle on the road surface will be taken at a point by the mounting point of the slider because the distance from the slider to the road surface is too great.
When an area of→100 receives an impact of 200, the force is distributed over an area of 100.
The point of Slider, the area of 1, will be subjected to a tremendous force when it receives 200 impacts.
So, why not Slider? You think so, don't you?
Engine Guard】 【Engine Guard】. →“accept”.
[Slider] → By intentionally sliding the Motorcycle during a fall, the force of the impact is “ dissipated ”.
It is also thought to prevent the Motorcycle from spinning in the event of a fall by allowing it to slide in contact with the road surface.
Motorcycle back and forth in the event of a fallQuantity:Pair (for Left and Right) This prevents them from spinning into a "T" and breaking the Tank, Seat, and even this and that on the other side of the tipping over.
good point
◎Easy to install; can be easily attached to Frame with Bolt fasteners.
◎If it falls over, the Cowl can be prevented from being damaged by Slider's first contact with Asphalt and sliding!
◎If it should fall down...it will be much easier on your wallet compared to replacing the exterior.
◎Parenthesis is also good in appearance.
A bad point
Dis-→ Suitable for circuits rather than public roads.
The Motorcycle will slide on the road surface when it falls over, and there is no denying the possibility of secondary damage from momentum causing the Motorcycle to collide with GuardRail, a house, or an oncoming car on the other side. Still, the chances of getting home after a fall are much better than the LargeCrash that is sometimes seen in Race and other races when a fall occurs.
I think it is not a bad thing to have it attached, and depending on one's point of view, it may have the advantage of reducing human damage.
I'm glad I put it on for insurance purposes (laughs).
We also believe that it is also possible to protect the Large odd part→Crankcase from falling if it is broken in the event of a fall.
And Crankcase damage = scrapped car.
I would suggest that Riders who are more likely to fall over at low speeds should add an engine slider. → I think that at low speeds, the vehicle will have less force on the body, less slippage, and will protect the exterior.
View detail
Glad I noticed it early!
This is a z900RS with YOSHIMURAHand Bent.
I wanted a Maintenance Stand, but I was a bit apprehensive.
In conclusion, we found that a common ordinary maintenance stand could not be used for YOSHIMURAHand Bent.
View detail
Fits: SUZUKI V-STROM250, SUZUKI V-STROM250, SUZUKI V-STROM250
Casually Guard
I didn't want to have a LargeGuard, so I purchased this product. View detail
Quite high quality
We have not taken into account what happens in the event of a fall from the beginning. (If it is just a standing fall, the Pannier and Frame Slider will be grounded, but not the Swing Arm.)
Therefore, although there was a cheaper Axle Slider that was a little smaller, I chose this product because I wanted a red undercarriage accent (since the wheel's rim tape is red, I wanted to unify the undercarriage accent in red).
I am satisfied, although it seems a little too large.
It would have been nice if Bolt was the same color, but I think I should have painted that much myself.
Incidentally, the compatible car models on Webike did not include the GSX-S1000GT, but the SPEEDRA webpage included the GT, and it could actually be installed without any modification.
View detail