Reviews
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
Required for Flywheel removal
Used to loosen the center bolt when removing the flywheel.
Functionality is fine.
The restrains on the Adjustment Bolt were reluctant to move and could not be fixed properly without support.
View detail
Belt has no durability.
[How is it used?
I bought this for EngineO/H when Restore TZr50R.
I fixed the Flywheel with this product and removed the Crankshaft Nut and ClutchGEAR Nut.
Was the one you received as per Image?
The image was exactly as shown in the picture, and although there were several other manufacturers with similar pictures, Minimoto was the cheapest, so I selected Minimoto. I selected Minimoto because it was the cheapest price.
How was your experience with it?
The EngineO/H was successfully used and EngineO/H was successfully used.
However, Belt's durability was almost non-existent, and after a few uses, Belt's reddish coating was falling apart,
Although it can be used for a time, we worked with caution because shavings of the film could enter the Engine.
[Points to note]
When using it for engine O/H, the belt of the Flywheel side and the Holder must be degreased with parts cleaneretc. or it will not slide easily and cannot be fixed. Also, since the handle is short and it is difficult to apply the Torque, it is better to use a PVC pipe or similar to extend the length of the handle.
How did it compare to other products?
I have never used products from other manufacturers, but I have a feeling that the very cheap products sold on the Net are probably from the same supplier, so if you don't buy products from a proper manufacturer and price, you might as well buy Net products on the assumption that they will be crushed.
View detail
Not for groms.
Purchased for installation of High Camshaft on Grom, but it was too short to fix. View detail
Versatile Holding Tool for your Maintenance Needs
About quality and texture: I am happy with the quality of the pulley holder from Kitaco made from a steel construction with a PVC coating over the band to help improve it's hold.About the feeling of use: I have used this tool to hold the clutch and flywheel on my Honda Grom when removal of these parts were required for maintenance with great success. The adjustable band makes this tool very versatile for varies sized motorcycle parts.Products to buy together: Some more tooling like a center lock nut wrench would also be desirable to purchase along side the pulley holder so when it comes time to remove the clutch assembly and oil spinner on your Honda Grom you have all the special tooling required to complete the job.Difficulty of installation: The process to install takes a few minutes, place the pulley holder around the part that needs to be held and adjust the band if required. Tighten down the T handle so that the band holder does not allow the part to spin as you undo the fastener securing the part. Not difficult to do.Cost performance and comparison with other products: Good costing as this is a quality made band holder from Kitaco that has with stood numerous usage without failure as compared to the first band hold that I purchased from another site that failed soon after.About shipping and packaging: The faster shipping options are too expensive for myself so I just have to wait for my part to arrive via sea freight. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged.Any concerns, cautions, or advice when purchasing: These band holder are limited to the sized parts they can hold. No smaller the 6cm in diameter and no larger then 12cm in diameter. View detail
For Scooter.
I purchased this product to replace the drivetrain on my Scooter.
However, I used it first for bore up work on a friend's SUPER CUB.
It works without any problems.
View detail
Good tool if used as intended.
This tool does what you want if you use it for its intended purpose. I bought the Husqvarna flywheel to hold while tightening the nut. Some said it failed and didn't do its job. Don't use it to change the oil filters in your car or load your ex-girlfriend's tire and it should work just fine. The safest non-destructive way to hold the flywheel for removal of the highly torqued nut. Could use a stronger clamping shaft to hold things while re-torquing the nut during installation. Bends a little too easily. Also, the vinyl coating on the band is slippery on a smooth flywheel surface. Powdered resin solves the slip issue. I've used this on a few motorcycles, Honda and Husky and it still looks and works as it should. I recommend it. View detail
I feel like I've been cheated.
To be more precise, this tool can only be used to remove the Pulley side and to install the Clutch Side.
We don't use Rose's because it is Air, but we wanted to use it for Torque management when embedding...
I managed to fool them into thinking it was better than nothing.
View detail
Fits: HONDA ZOOMER(Ruckus)
KN Planning Exclusive Tool for Disassembling of Drive System
I bought it because I thought it would be universal to some extent, although it was designed to be used with ZOOMER.
Exclusive Tool for Disassembling of Drive System". This is a straightforward Naming product, but it is a proper product name.
The common trade name is Universal holder.
As the name suggests, it is used to prevent parts from turning when removing the clutch or pulley face of the scooter.
I used it to service my ADDRESS V100, but I feel like I need to think carefully about where the force is applied to use it on the Pulley face side.
I use it with electric Impact wrench as a supplement.
View detail
Good tool if used as intended.
This tool does what you're asked if you use it for its intended purpose. Bought it to hold the flywheel on my Honda crf250r while tightening the nut. Some mentioned that it failed and didn't do its job. Don't use it to change the oil filters in your car or put on your ex-girlfriend's tire and it should work just fine. I've used it on a few bikes, KTM and Honda it still looks and works as it should. I would buy it again as it's the right price for a tool you can use about 6 times in your life.shipping is very fast,well packaged, thanks webike. View detail
Thoughts on using it
[How is it used?
Used to remove Clutch and Pulley from Scooter
Was the one you received as per Image?
No problem as per Image.
How was your experience with it?
I have not had any inconvenience at all.
[Points to note]
The holes are positioned in the most comfortable manner (opening angle), and then tightened and secured in place.
How did it compare to other products?
The product is not different in usability compared to the well-known manufacturer's product used in the past, and this product can be recommended because it is less expensive.
View detail
Fits: HONDA ZOOMER(Ruckus)
Required for drivetrain maintenance.
This tool is indispensable for removing and installing pulleys and clutches. There are a variety of such tools sold by various companies, and we were not sure which one to purchase, but we chose KN Kikaku's tool this time because of its price and the fact that the company is a manufacturer that handles many ZOOMER parts. There are two types of ZOOMER parts:one is a hook type, like this one, and the other is a type that wraps around the circumference of the product, so you can choose the one you like best. I used the one shown in the photo by fixing it to the ground and had no problem using it. I think this is the most common way to use the Case when working alone. The torque for installation is large, so it is difficult to hold it down with the left hand and tighten it with the right hand. If you do not want to scratch the car body side, I think it will be a good idea to protect it with cloth to prevent wounds. View detail
Convenient for everything
I bought this for maintenance of my scooter's drivetrain.
Until I purchased the Impact wrench, I had to hold the clutch outer with this product and remove it with the Ratchet wrench.
The plug-in type universal holder was difficult to use with the Clutch outer tightening torque, so I needed two types.
The price is very Reasonable and it is very easy to use.
I've been using it for about two years and it hasn't broken yet.
Now that I have purchased an electric impact wrench, I have less opportunity to use it on the drive train, but instead I use it around the crank and when removing the generator.
I feel that there are many opportunities to use it not only for Motorcycle, but also for cars.
Since it is variable and can be used for a variety of sizes, I think having one for now will come in handy later.
It is flat when placed on the ground, so it can be placed in the crevices of shelves, and I keep it hanging on the wall so it does not take up much space.
Sometimes when the lid of a bottle is too hard to open, I use this product, and it opens in one shot. However, be careful not to tighten it too much or it will break.
View detail
It's cheap and fully functional.
I purchased this product to replace the Reinforced Clutch and Reinforced Oil Pump on my SUPER CUB 50FI.
I was able to hold it firmly without any slippage.
It's cheap and large, and I'm happy with it.
View detail
Pin is short and unusable.
The pin is short and the holder is at an angle, making it difficult to apply force and work.
When incorporating Mr. Takekawa's parts, the Manufacturer listed them as tools, but…
View detail
If the payment is by Silver bank transfer, you will be contacted separately, I don't know how to contact you.
I don't know how to do Cancellation, give me your contact info. View detail
I would like to cancel this product.
How do I make a cancellation? View detail
I want to do Cancellation!
I'd like to cancel my reservationHow do I cancel my reservation? View detail
Cancellation
I'm pissed off, I can't cancel anyway, I want my Gold back. View detail
Cancellation.
This product can only be used for Honda motorcycles. View detail