Reviews
Fits: KAWASAKI Ninja1000, KAWASAKI Z1000
Shinobu Sen Rear Torque rod
We stocked RearTorque rods from Shinobu Sen.
It is almost a visual obsession!
Dare I say, lightweight? (^^)
Is this Torque rod as accurate as the OEM Torque rod?
OEM was quite hard and used SmallHammer for removal.
The external Torque rod did not go in easily.
But since I had already removed it, I put it in by tapping hanghang with Hammer while checking the insertion angle.
Remove it with no care and install it with the latest care to put it in!
Finally, the specified Torque 3.5kgf-m is installed using the Torque wrench.
The rest is done by applying a split pin to prevent ha-gap!
Except for the difficulty of removing and inserting, I think it is an easy task even for beginners. (^^)
View detail
Fits: KAWASAKI ZrX1200DAEG , KAWASAKI ZRX1200 R
Processing Required
Is this incompatible with Active's Rear caliper support?
I had to use Grinderetc. to cut off the radius to install it.
View detail
Caliper and Rotor outlines are hit. It becomes impossible to run.
Rotor outline hits Caliper. Not this one! View detail
na metal craft torque rod
pure quality , perfect fit and sits nice next to the gold caliper , very high quality , and will never rust great , brembo calipers are next on the bucket list , then ohlin rears View detail
Fits: KAWASAKI ZrX1200DAEG , KAWASAKI ZRX1200 R
A bit lighter
I replaced the NORMAL steel Torque rod with this one to reduce weight and appearance. It is light because it is made of Duralumin compared with NORMAL which I removed. Because it interferes with the Wheel when pulling out the Bolt of the front side to the inside, it was troublesome because it was necessary to loosen the Excessen and move the Wheel to the front, but the texture is good and I am satisfied. View detail
Good installation
Buy for Φ 220 and make it to Mukawa river Big Floating Disc
I use it in combination.
Because Mukawa's Disk size is Φ 225
Manufacturer Recommended disc It is not a diameter, but it was able to be installed easily.
The radial gap is not consequently Limit
It seems to be good not to scrape Pad.
I replaced Pad with DAYTONAGolden Pad at WaveRotor
I hear a sound in the early stages of braking.
I do not test the Pad included with Caliper so it sounds
It is unknown whether it does not go out.
I was satisfied with COSPA because I did not manufacture one-off
Manufacturer conformity Rotor Because it is not diameter, please be aware of that point..
View detail
Fits: KAWASAKI ZRX1200 R, KAWASAKI ZrX1200DAEG
For appearance
It is a Parts whose performance does not quite understand to an amateur like me.
Making is well done and may look good as one point.
View detail
I decided by the price
Caliper support for 320 mm disc has some choices, but for the 300 mm Disc of D TRAX X, I could only find this and K & T, so I chose this cheap price.
Although its shape is cool, it has almost no presence as it does not fit in the field of view.
But in combination with OEMCaliper there is no dissatisfaction because only Support will float outstandingly.
Accuracy is also good, more than one year after purchase, but there is not particularly trouble.
Those who are considering disc diversion of D tiger X are recommended because it is somewhat cheaper to buy this and disc separately than those sold in Kit.
View detail
Clean cutting products.
Steel's Torque rod of OEM tried to replace because the paint was scratched and dirty due to rust. I am happy because it is lighter than the OEM because it has a beautiful cutting process and the finish of Anodized is glossy. By the way, in my case, when I installed it properly, the Rubber cover covering the previous Bolt interfered with the Exhaust System and it seemed to melt so I attached it to the reverse side.
I hope the price is a little cheaper but I guess there is no way to consider processing Cost.
View detail
Interference Large, Processing Large
To say that it corresponds to 220 mm disc, Caliper slightly interferes with Floating pin depending on disc.
(Us, SHIFT UPSHIFT UP made EURO MOTARD Wave Disk Rotor 220 mm is used).
Also, if it is replaced with Thailand OEMAluminum Wheel, it interferes with the Wheel spoke part unexpectedly.
Spec. Large machining is required for vehicles of the vehicle, please be careful when purchasing.
View detail
Though things are a dream, only that
It is a Caliper support for enabling Rotor for D - TRACKER - X of 300 Φ. It looks beautiful in Billet parts. I think that it can be used for a long time because it seems to be solid Anodized.
However, the length of the attached Bolt was different. I do not have the instruction manual in particular, I think that the quality of the product as a whole is bad. Even if Bolt's Length is different if the thickness of the mounting part is different, it is not so. The shorter Bolt seems to contain only less than half of the Screw hole of BrakeCaliper.
Package at the time of delivery was in a state where it is wrapped in PetitPetit and Label is not pasted. I think that it would have been good if this was K & T.
View detail