Reviews
Helps to reduce weight under Spring
This is one of the parts that must be replaced when you buy a motorcycle. Normally, it is no color, but this time, we decided to go with Blue. You may not be able to feel the difference, but it is half of a dress-up. View detail
monogamous
It feels very light to hold.
However, the pictures are very confusing.
Quantity:I thought it was 2pcs, so I had to order again, which doubled the shipping cost.
View detail
Before Products
There was one Hexagon Bolt mixed in with what should have been a Torx bolt. How is this possible? I doubt the management system. View detail
Self-satisfaction is very high.
Since the pad pin of the Front brake is Titanium, the Rear should be Titanium as well.
The OEM parts are the same as those for the Z750, so the Z750 parts can be used for the Z900RS.
(Note that the front part is the same as for NINJA1000, but the rear part is different from NINJA1000.)
Front still has some things that can be Appeal in appearance, such as tints and Beta pins, but Rear has none at all.
However, the OEMPin is more painful in Rear than in Rear, and I feel the difference in the role of the Pin in Slide-type Caliper.
The CaliperBody slide pin should also be thoroughly cleaned and greased up.
If you can see the caliper moving when you operate the brake pedal or shake the caliper, you will have a sharp rear brake with no drag.
As for cosmetics, unlike Front, the cosmetic appearance is almost Zero, but the self-satisfaction of converting to a very lightweight Titanium Pin for a little less than 2000 yen is higher than Front, so overall it is the same at 4 stars.
The pins of this brand's products are generally longer than those of the OEMs, which is true, but not to the extent that it bothers me.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Ninja1000
Highly self-satisfied
While I was rubbing out the Caliper piston in preparation for the car inspection, it occurred to me that I would like to make the pad pins slippery.
Stainless Steel was fine, but 64Material:I found a Titanium one and used this one.
I can't find any hits for Z900RS, but OEM parts use the same pin as NINJA1000 (Rear is different), so I will use the NINJA1000.
The dimensions of this product will be slightly extended to include a Beta pin, so in essence, it is a Tokico SportsCaliper type product.
I can't say that the effect is immediate for the price, but I tell myself that every little bit helps the fee ring.
The black BoltSocket part becomes titanium-colored, and the Beta pin inside the Caliper is a key point.
In terms of weight, it is incomparably lighter than the OEMPin.
For those seeking effectiveness, we recommend frequent cleaning or replacement of OEMPins for a few hundred yen.
For those who seek self-satisfaction, we recommend the Large variant.
View detail
Looks are everything.
The effect of weight reduction and stiffness improvement is naturally too small.
Yes, looks are everything. I am satisfied.
View detail
For installation of front brake disc
Bolt was also replaced along with Front Disc replacement.
I changed the whole set because it is also a place to apply Screw lock and it is troublesome to clean.
We would like to see how durable it is.
View detail
Brake Caliper/Brake hose Quick Release Connector
This is not the same as the picture, but Color on 64Titanium alloy Gold.:I have an anodized Gray type. Isn't this just an anodized aluminum product? I can't trust it, but I don't think it's the same at all.
I have spent almost half a million dollars to change most of the screw bolts and shaft etc. on my Ducati 900ss to 64Titanium Alloy Gold, but I don't trust them this time.
I would like you to let me prove the product if I can't tell by looking at it.
I'm glad I decided to pay later, I'm checking my email now to return it.
View detail
Fits: SUZUKI GSX-R750, SUZUKI GSX-R750 K3, SUZUKI GSX-R750 K1, SUZUKI GSX-R750 K1-K3, SUZUKI GSX-R750, SUZUKI GSX-R750 K3, SUZUKI GSX-R750 K1, SUZUKI GSX-R750 K1-K3
I think it is excellent workmanship. I am not sure about the durability.
I think the product is worth the price. View detail
The pure bolt of R1 was lightweight by the air type. It contributes to a weight saving not a little.
The pure bolt of R1 was lightweight by the air type.
It contributes to a weight saving not a little.
View detail
The premium was made according to the rotor. It contributes to a weight saving not a little.
The premium was made according to the rotor.
It contributes to a weight saving not a little.
View detail
Fits: KAWASAKI ZEPHYR1100 [Zephyr]., KAWASAKI ZEPHYR1100 [Zephyr].
Titanium Bolt
It is pricey, but you can tell how light it is just by holding it.
I made the change when I Renewal the suspension.
You may not be able to feel whether the weight has become lighter when you put it on, but there is a change in appearance and actual weight.
View detail
Material:Replace with TitaniumPad pin
I was concerned about rust and uneven wear with OEMPad pins, so I decided to use this material to make maintenance as easy as possible.:I purchased a TitaniumPad pin.
Although you have to look closely to see the change, it is lighter than the OEMPad pin.
I am satisfied with the high quality of the product.
If the durability is good, I would recommend it without any complaints, but this is something I cannot judge until I use it for a while, so if there are any problems, I would like to add and correct them in Impression.
*However, we have used the company's pad pin in other vehicles and have had no problems so far, so we consider Large sturdy.
View detail
I bought it for Fashion purposes.
I bought it completely for appearance.
I was a little bit uncomfortable with bremboOEM's Chromoly rusting.
I can't tell any difference between the Fee Rings. I am not sure if there is any difference in the fee rings, but I am doing maintenance of the piston and oil seal together when I replace them.
I tightened the Torque at 25N.m. I found the Titanium to be stiffer or tightly tightened compared to the Chromoly.
Matte Black Caliper with Polished Titanium is a nice Parenthesis.
The self-fulfillment level is moderately high for this product.
The price of Bolt is very expensive, and for those who don't know, it may seem silly. It is a very expensive product for a Bolt, but I think it is satisfactory.
It is probably the most expensive Bolt I have ever bought in my lifetime.
There is also a Titaniumium Bolt for a slightly lower price, but I was excited because it is a security part.
View detail
Fits: YAMAHA OEM SumitomoMOS Monoblock caliper TitaniumBrake Pads Pin
Pad pin replacement for ease of maintenance
I had been lightly applying water-resistance paper to the OEM pins, but I began to worry that it might accelerate the wear of the pins, so I decided to use Material:I thought maintenance might be easier with Titanium, so I purchased this product.
I have purchased TitaniumParts for CYGNUSX in the past, and I usually prefer Titaniumium color without surface treatment, but this time, I decided to go with Champagne gold because it is an installation point where shavings from the pad may adhere and friction with the pad may be harsh. However, this time, I decided to use anodized Champagne gold because the pad is likely to be subjected to abrasion and friction with the pad and because the Brake Pads are gold, so it would be less noticeable.
Compared to OEMPin, it is very lightweight and seems to remove dirt easily, which I am satisfied with.
After running for a while, there seems to be no particular problem, so we plan to apply a Clip dropout prevention in the future.
View detail
A little long, but no problem.
Used on front brake caliper for Honda NSR250R MC21.
I got a used Brake Caliper that did not have a Pad pin.
It was frustrating to go out of my way to buy OEM, so I was torn between DAYTONA's Stainless Steel pad pin and Titanium64's Titaniumium pad pin, but I chose Titanium64's Titaniumium pad pin because the price difference was not so great and I wanted to reduce the weight as much as possible. I chose the Titaniumium pad pin because the price difference was not so much and I wanted to reduce the weight as much as possible.
The quality and texture are second to none.
Once installed, these parts are completely invisible, so they tend to be put off as custom parts, but they are highly recommended.
The brake area is easily contaminated with brake dust and prone to rust, so we think the titanium conversion is a good way to improve maintainability.
Stainless Steel is not rustproof either.
Incidentally, many of these parts are universal to some extent, and I think this product is the same as other NISSINCalipers, although the part numbers are different.
It is made a little longer than OEM Product and has a slightly higher penetrating volume.
It is completely safe to use
I would have liked to put a Beta pin on it, but I don't have the skills or equipment to drill a precise hole in thin titanium, so I gave up on that.
Note that for Front is Quantity:1 Set for 1 Vehicle (Quantity):(2 pcs) It was in.
Pad pin is the Quantity:Is there 4 2pc front double disk vehicles in the box? I think so.
In general, I have no complaints at all and recommend Custom parts.
Buying OEM Parts as for Repair is a good option, but it is also a good price option.
View detail
Fits: HONDA CBR250R (MC41), HONDA CBR250R (MC41)
The quality is good, but …
I was told that the CBR250R (MC41) fits, but the overall length seems to be a little shorter than the OEM.
Although the 250cc is not very powerful, we are concerned about the shortening of the Bolt's grip, even if it is only a few millimeters, because we believe that a certain amount of force will be applied to the Caliper, so we have decided not to use it this time.
It is a pity because the construction is good.
View detail
Fits: DUCATI MONSTER 900 [Monster]., DUCATI MONSTER 900 [Monster] S I.E, DUCATI MONSTER 900 [Monster] Dark, DUCATI MONSTER 900 [Monster]., DUCATI MONSTER 900 [Monster] S I.E, DUCATI MONSTER 900 [Monster] Dark
I don't want to think about costa...
I bought the Titaniumium Bolt for the first time because the OEM one was starting to show rust and corrosion. It is a bad Image because I can't feel the cost effect immediately, but I feel satisfied with it. View detail
Fits: SUZUKI GSR400, SUZUKI GSR400
Some parts are incompatible
GSR400 (Gk7EA) Purchased for a 2010
Replacement is possible without any difficulty. Just by changing rusty OEM Bolt to Titanium, it will look better. But! The BridgeBolt was fine, but the Pat pin was not able to fit.:The 2pc did not work. It is necessary to pay attention to whether the person who considers the purchase fits Caliper of your vehicle. It is a product of about 15000 yen. 5 pieces each of One Side, Quantity of 10 pieces in total.:Since it is a Set, Quantity:For about 3,000 yen for 2pc, I became useless. The feeling of use is …I think that there is a thing that the Pin part has not been exchanged, but I was not able to understand it to myself of the amateur to say "HADRILL". But well, I think it is good because the appearance has been improved. It is expensive.
View detail
Fits: SUZUKI BANDIT1250 [Bandit] BANDIT, SUZUKI BANDIT1250 [Bandit] BANDIT
Bolt size is wrong.
For bandit1250
OEMBolt size
Total length:approx. 24mm Bolt head:2.8mm Bolt body:7.3mm Screw part:13.6mm
regarding
Titaniumium BoltSize
Total length:approx. 36mm Bolt head:3.0mm Bolt body:10mm Screw part:22.5mm
As for the weight, it's at least 1g lighter per bottle.
The moment you see this much difference, it seems impossible, but still...
Because of the long torso, even if you tighten it with OEM tightening Torque
Rotor moves with a rattle.
Not available.
Manufacturer, what is the conformity guarantee of the webike you are selling?
Because it is easy to mistake it for a warranty that can be installed
Caution
View detail