【SP Takegawa】Hyper LED Blinker Bulb Kit Review

It is recommended for those who want to keep the NORMAL blinker lens etc.

Tail lamp was originally LED, and the headlight is also LED. If it becomes like this, it's natural that I want to make the blinker LED too. (？) thing....I wanted to do something with the STD Shape, but after touring the other day, I told my wife It's hard for Blinker to see when Brake is on. That being said, I was inspired to buy one. I still wonder if the Valve lights usually lose out to the LED lights.
Because there is not much space inside of Blinker lamp when I confirmed beforehand, I bought this one, but the height of LED Bulb is unexpectedly low, and I think that the product of 05-08-0098 was good when I felt that I put it on.
Because there was no reflector at all in the Blinker of DL1000 V-STROM and it was still Black color of resin, I put Aluminum Tape inside instead of the reflector and made it so that the light would not become useless. The sharpness of the flashing is good, and I am satisfied. The only thing that was worried about was that the indicator in Meter when operating was not good. "Blinking" Not the Blinker. "point" When the Perdition. The thing is that the light is reduced when the I looked it up in the Roadway Vehicle Act and found that Article 41, Section 2, Article 137, 4-12 of the "A device shall be provided to indicate to the driver the operational status of the device. It's just that it is, so I don't think it's a problem for car inspection.
By the way, the area of the lighting part of the blinker lamp is determined to be more than 7? or more, orange, the brightness of the bulb is more than 10W and less than 60W, and the number of blinks is less than 60-120 times per minute. Because this time it is NORMAL and Relay is also for LED, the function of the important blinker corresponds sufficiently.
View detail

LED is still high as usual

I am satisfied except price..
Valve exchange can be done without removing Cowl, and when attaching the attached relay
Seat down Remove Cowl of Right Side only. Work is enough for as long as one hour.
Prepare Nipper for RearLens cover + Driver, Tie Wrap's Cut.
Like everyone said Kit (Relay) Relay's "Chi - Chirping
Although it disappears, Ninja 250 does not bother because it was Small because it was originally Ka Chica tone,
Since the winker is displayed on Meter, I think that it is a particularly problem.
Thanks to LEDization, until that time Barrel from the blinking light bulbs, light Sharp
It turns into flashing and it is Large satisfied.
In addition, power consumption, out of ball etc etc etc. Also considering whether LEDization is very significant.
The cost of LED is surprisingly reasonably cheap, so if the price becomes cheaper at a moment ◎ View detail

Mukawa LED Blinker

PCX is replaced by Valve 1 / 10 consumption and reduce the burden on Battery
Crispy flashing Satisfactory level such as sufficient light intensity and bulb's stealth effect. Relay is Wide range and sound is silent. Even in other types of cars / It seems that it will be the power consumption of 5. View detail

All is in one.

I installed it in the 2013 PCX. This Set contains LED Bulb and Blinker relay corresponding to LED, so there are no other necessary items.
It is necessary to open the Front mask in order to exchange the Relay, but is it still to be completed within an hour until all the work is completed?
I am satisfied with the flicker with a peculiar LED View detail

It shines beautifully!

Takegawa LED blinker BulbKit is attached to PCX for power saving and apparent Makeover.
Illuminated in a beautiful color compared to NORMAL bulbs, I think that Orange bulb was visible through Lens until now Clear, I think that refreshing looked a bit.
It's a bit expensive, but after all Takegawa is good! View detail