【ZETA】Bar end plug Review
Fits to Kawasaki Ninja 250R and Z400
[How is it used?
Both Ninja250R and Z400 are mainly used for touring.
The Ninja 250R is used on the end of a Penske Separate handle with an inner weight.
Z400 is used with ZETA CX Handlebar ends.
The Ninja 250R has been used for about 4 years and the Z400 for about 3 months.
Size is 29mm for both.
Was the one you received as per Image?
I am satisfied with the Large change in color and finish of Anodized as per Image.
The machining accuracy of the contact surface with the handlebar is good, and the contact is firm.
Was the installation difficult?
When installing the Ninja 250R, the bolt that came with the Ninja 250R was not long enough to accommodate the inner weight, so we were able to prepare a pot screw. (+head) Therefore, we worked carefully not to lick the screw head when tightening it.
On Z400, it can be easily installed with the included Bolt.
How was your experience with it?
This Bar End is characterized by its flat shape and I am a good looking person. (Wide flat surface and strong Impact) and falls, and prefer to use it because they think it is a functional Merit.
Anodized colors and hold up well and are visually satisfying.
As for the Merit in the event of a fall, the flat shape of the handlebar prevents it from being caught on the road surface, and since it slides down, it is considered to be less damaging to the handlebar. (If the shape is sharp, Moment may occur due to catching and the Handlebar may bend.)
Although it was not me, my wife and the owner of Ninja250R suffered a standing fall and a slipdown, respectively, but there was no damage to the handlebar and it served its purpose well.
Naturally, the Damage to the Body is firm, so if it is scraped by a fall, it is recommended that it be replaced before injury occurs.
[Included Parts:were they on?
Bolt、Anchor、Material:PlasticWasher
[Was there anything that disappointed you?
None
Point and hang of installation
The key hang in removing the OEMBar End is how to remove the Screw lock agent.
Although tools are required, the Screw lock agent will loosen when heated, so if the OEMBar End can be discarded, the fastest and surest way is to cure the Grip with wet Toweletc. and burn it with a Burner.
If you have a Solder iron, you can slowly heat the Screw part.
For +head Screw, a Shock driver would be perfect.
Responses
Other reviews
I really wasn't going to buy this, but ….
Open endGrip requiredType
I used to use a Type that drilled Screw holes in Throttle, but I wonder why it was discontinued.
Quantity:Pair (for Left and Right) Both Material inside the bar:The aluminum tube is inserted and the screw is tightened to open the tube, so it must be re-tightened often or it will suddenly fall out while driving.
For this reason, the Throttle side must also be changed to an open end one.
Completely Material:It is aluminum and weighs almost nothing, so it can be used with or without use with little or no change in sensation.
View detail
Installed during handlebar replacement
I installed it on my HUSQVARNA TE250 2017 which I always use for forest road Touring.
This Bar End can be used for both large and small inner diameters by changing the Adapter.
I didn't like the Bar End that popped out so much, so this thin Bar End was very Balanced and just right.
View detail
Buy.
Well, it's a classic.
Buy!
MFJ Race may fail vehicle inspection in Regulation.
Confirmation.
View detail
The size was perfect!
I used it on the Grip end side with the Grip heater on my CL500. The OEM handlebar end has female threads and can be installed perfectly with the included bolts. View detail
Accent and minimum defense Up
I use it on my car KLX250es, I replaced the handlebar with zeta cx bar mx412Blue, so I bought it to match the color.
It is not only good looking, but it is also effective in protecting the throttle cone in case of a fall.
View detail